ページ1に含まれる内容の要旨
Touchcomputer User Guide
15A2 15" LCD Multifunction Touchcomputer
[Model ESY15A2]
ページ2に含まれる内容の要旨
Elo TouchSystems Touchcomputer User Guide 15" LCD Multifunction Touchcomputer 15A2 Revision A P/N E293646 Elo TouchSystems 1-800-557-1458 www.elotouch.com
ページ3に含まれる内容の要旨
Copyright c 2008 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no re
ページ4に含まれる内容の要旨
Table of Contents Chapter 1 Cash Drawer ......................................... 30 Setup 6 Ethernet ................................................ 30 Unpacking Your Touchcomputer ......................... 6 Serial .................................................... 30 Product Overview ................................................ 7 Microphone Input................................ 30 Front View ..................................................... 7 Audio Output.......................
ページ5に含まれる内容の要旨
Speaker Bar .............................................. 52 Wireless Card ........................................... 53 TV Tuner .................................................. 53 Modem Card ............................................ 54 Environmental Specifications.......................... 55 Temperature Ranges ................................ 55 Humidity .................................................. 55 Altitude .................................................... 55 Chapter 6 Tech
ページ6に含まれる内容の要旨
C H A P T E R 1 Setup This chapter discusses how to set up and test your touchcomputer and any included peripheral options. Unpacking Your Touchcomputer Check that the following items are present and in good condition: OR Touchcomputer Power cable US/Canadian European power cable PS2/Y cable CD and Quick Install Guide Power Adapter DB9 adapter cable Elo TouchSystems 15A2 User Guide 6
ページ7に含まれる内容の要旨
Product Overview Front View Rear View Note: Shown with optional peripherals Elo TouchSystems 15A2 User Guide 7
ページ8に含まれる内容の要旨
Side View Note: Shown with optional peripherals Base Bottom View Elo TouchSystems 15A2 User Guide 8
ページ9に含まれる内容の要旨
Display Orientation Elo TouchSystems 15A2 User Guide 9
ページ10に含まれる内容の要旨
Display Orientation with Peripherals Elo TouchSystems 15A2 User Guide 10
ページ11に含まれる内容の要旨
Initial Turn-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touchcomputer hardware configuration and connected devices. To setup the Windows OS for the touchcomputer, turn on the touchcomputer and follow the instructions on the screen. Language Selection When the following window appears, you have the option of changing the language used in menus and dialogs. Click Customize. The Regional and Language window shown below w
ページ12に含まれる内容の要旨
Select the Language tab. The window shown below will appear. Select the desired language in the drop-down list labeled Language used in menus and dialogs. Elo TouchSystems 15A2 User Guide 12
ページ13に含まれる内容の要旨
Time-zone selection When the following window appears, you may change the time-zone, date, and/or time of the touchcomputer. After making any changes, click Next to finish. Windows Setup will complete the initialization of the touchcomputer. Elo TouchSystems 15A2 User Guide 13
ページ14に含まれる内容の要旨
Test Devices The touchcomputer can be pre-installed with several different hardware options. To test an optional device that is installed on the touchcomputer, follow the instructions below. NOTE: Testing icons are located on the desktop. Testing of a particular device can only be done after the device is properly installed. Testing the Touchscreen The touchscreen is pre-calibrated for accurate touch response. Calibration* If for any reason the touchscreen needs to be re-calibrated, double-click
ページ15に含まれる内容の要旨
Testing the Magnetic Stripe Reader (MSR) (optional) Testing in USB MSR Keyboard (KB) Emulation Mode 1. Double-click the KB MSR Test icon to open the Notepad application 2. Slide the card through the MSR and verify that the data is displayed in the application window. Testing in USB MSR Human Interface Device (HID) Mode 1. Double-click the HID MSR Test icon to start the test application. 2. Click the Read Cards button. 3. Slide the card through the MSR and verify that the data is displayed in the
ページ16に含まれる内容の要旨
Converting MSR from Keyboard Emulation to HID and vice versa 1. Double-click the MSR Change Mode icon to start the switch application. 2. Click on HID Mode to switch to HID mode OR click on Keyboard Mode to switch to Keyboard mode. The dimmed box will indicate the current setting. 3. Click Quit to close the window. Elo TouchSystems 15A2 User Guide 16
ページ17に含まれる内容の要旨
Testing the Customer Display (optional) 1. Double-click the CustDisplay Test icon. 2. Verify that the device shows "EloTouch Systems Customer Display" on the display. Elo TouchSystems 15A2 User Guide 17
ページ18に含まれる内容の要旨
Testing the Finger Print Reader (optional) 1. Double-click the Fingerprint Reader Test icon to start the test application. 2. Place your finger on the fingerprint reader sensor and verify that the image of your fingerprint is displayed on the application window. Elo TouchSystems 15A2 User Guide 18
ページ19に含まれる内容の要旨
Testing the Barcode Scanner (optional) 1. Determine which port the barcode scanner is using: a. In Windows Control Panel, start the Computer Management application b. In Computer Management, select Device Manager. In the Right pane, look under the Ports section, and note the COM value of the USB -Serial Port object. 2. Double-click on the Barcode Scanner Test icon to start the following application: Elo TouchSystems 15A2 User Guide 19
ページ20に含まれる内容の要旨
1. Change the port value to match the value you retrieved from the Device Manager. 2. Click Connect. You should see the text Connected in the Messages field. 3. In the box labeled Param Number, enter the value 238. 4. In the box labeled “New Value” enter the value 1. 5. Check the box labeled Permanent Param Change. 6. Scan a barcode. The result should look similar to the following image: Elo TouchSystems 15A2 User Guide 20
