Vantec UGT-ST310Rの取扱説明書

デバイスVantec UGT-ST310Rの取扱説明書

デバイス: Vantec UGT-ST310R
カテゴリ: コンピュータハードウェア
メーカー: Vantec
サイズ: 0.21 MB
追加した日付: 7/25/2014
ページ数: 20
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスVantec UGT-ST310Rの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Vantec UGT-ST310Rに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Vantec UGT-ST310Rをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Vantec UGT-ST310Rのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Vantec UGT-ST310Rの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Vantec UGT-ST310R 取扱説明書 - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Vantec UGT-ST310Rを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Vantec UGT-ST310Rの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨





6-Port SATA II 150 PCI Host
Card w/RAID


User Manual
Model: UGT-ST310R








All brand names and trademarks are properties of their respective owners.

w w w . v a n t e c u s a . c o m

ページ2に含まれる内容の要旨

Table of Contents 1. Bus Interface.......................................... 3 2. Connectors............................................. 3 3. Package Contents.................................. 3 4. System Requirements............................ 4 5. Hardware Description............................. 4 6. Hardware Installation ............................. 5 7. Device Connection................................. 5 8. RAID Arrays ........................................... 6 RAID 0 (Strip

ページ3に含まれる内容の要旨

Features • Silicon Image SiI3114 SATA controller chip • Compliant with PCI Specification, Rev. 2.3, 32-bit, 33/66Mhz • Compliant with Serial ATA 1.0 specification • Provides four independent channels to support up to four Serial ATA drives • Supports RAID0 (striping), RAID1 (mirroring), RAID5 (Parity RAID), RAID 0+1(mirroring + striping) and Concatenation (JBOD), Individual Mode • HDDs function normally when not in RAID sets • Supports SATA up to 150MB/Sec • Supports Windows® 2000, XP

ページ4に含まれる内容の要旨

System Requirements Pentium-class computer with one available PCI slot Windows® 2000, XP/2003 32/64bit, Vista 32/64bit Hardware Description G (Jumper Settings) JP Description Active Port J1-J4 1-2 close Enable SATA Connector F 2-3 close Enable SATA Connector C J5-J8 1-2 close Enable SATA Connector E 2-3 close Enable SATA Connector D UGT-ST310R Page 4

ページ5に含まれる内容の要旨

Note: There are six SATA ports in 6-Port SATA II 150 PCI Host Card w/RAID. We name these ports from A through F. Ports A to D are internal SATA ports. Ports E and F are external SATA ports. Changing the jumper settings allows you to select between external and internal ports to use. By default, Port A, B, C and D are working. Hardware Installation 1. Turn Off the power to your computer and any other connected peripheral devices. 2. Unplug the power cord form the back of the computer.

ページ6に含まれる内容の要旨

drive. 4. Attach the other end of the Serial ATA cable to the Serial ATA controller on the 6-Port SATA II 150 PCI Host Card w/RAID. 5. Follow the same instructions to connect up to four hard drives. Device connection is now complete. 6. Replace the computer cover and reconnect the power cord. RAID Arrays RAID Arrays are setup in the 6-Port SATA II 150 PCI Host Card w/RAID’s BIOS. RAID 0 (Striping) This RAID array to be used on New/Blank hard drives. Striping will destroy existing da

ページ7に含まれる内容の要旨

3. Select RAID0, then press Enter. 4. Select the number of drives then press Enter. 5. Select Auto configuration, then press Enter. 6. Input the RAID size, press Enter. 7. When asked Are You Sure (Y/N)?, press Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sure to exit (Y/N)?, press Y to exit and reboot. 10. Continue with FDISK and FORMAT steps as if you were installing a conventional hard drive. Manual configuration 1. As the BIOS boots press Ctrl+S or F4 when p

ページ8に含まれる内容の要旨

RAID 1 (Mirror) For New/Blank Hard Drives 1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS. 2. At the next screen select Create RAID Set, then press Enter. 3. At the next screen select RAID1 then press Enter. 4. Select Auto configuration, then press Enter. 5. Input the RAID size, press Enter. 6. When asked Are You Sure(Y/N)?, press Y to accept. 7. Press Ctrl+E to exit the BIOS. 8. When asked Are you sure to exit(Y/N)?, press Y to exit and reboot. 9. Conti

ページ9に含まれる内容の要旨

9. Input the RAID size, press Enter. 10. Press Ctrl+E to exit the BIOS. 11. When asked Are you sure to exit(Y/N)?, press Y to exit and reboot. Note: If during boot the RAID BIOS reports an RAID1 set is in Rebuild status, The rebuild will continue after boot sequence is complete, disregard the message, continue booting, and let the Mirror rebuild. Rebuilding a Failed Mirror Set When a failure to one member occurs, you will be notified either by the RAID BIOS during boot or by the SATA

ページ10に含まれる内容の要旨

use existing hard drive(s) with data. To create a RAID 0+1 set four hard drives are required. Auto configuration (recommended) The default chunk size is 64k when selecting Auto configuration. 1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS. 2. At the next screen select Create RAID Set, then press Enter. 3. Select RAID10, then press Enter. 4. Select Auto configuration, then press Enter. 5. Input the RAID size, press Enter. 6. When asked Are You Sure(Y/N)

ページ11に含まれる内容の要旨

6. Select chunk size from 8k, 16k, 32k, 64 or 128k, then press Enter. 7. Select the first drive, press Enter. 8. Select the second drive, press Enter. 9. Select the third drive, press Enter. 10. Select the fourth drive, press Enter. 11. Select Create without data copy then press Enter. 12. Input the RAID size, press Enter. 13. When asked Are You Sure(Y/N)?, press Y to accept. 14. Press Ctrl+E to exit the BIOS. 15. When asked Are you sure to exit(Y/N)?, press Y to exit and reboot. 16.

ページ12に含まれる内容の要旨

Enter. 3. Select RAID5, then press Enter. 4. Select the number of drives then press Enter. 5. Select Auto configuration, then press Enter. 6. Input the RAID size, press Enter. 7. When asked Are You Sure(Y/N)?, press Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sure to exit(Y/N)?, press Y to exit and reboot 10. Continue with FDISK and FORMAT steps as if you were installing a conventional hard drive. Manual configuration 1. As the BIOS boots press Ctrl+S or F4

ページ13に含まれる内容の要旨

and reboot. 15. Continue with FDISK and FORMAT steps as if you were installing a conventional hard drive. CONCATENATION (JBOD) This RAID array allows you to use one, two, three or four hard drives to a array. It does not provide any data protection or performance improvement but can be useful for utilizing leftover space on disks. 1. As the BIOS boots press Ctrl+F4 or F4 when prompted to enter the RAID BIOS. 2. At the next screen select Create RAID Set, then press Enter. 3. Select CO

ページ14に含まれる内容の要旨

2. Select Delete RAID Set, then press Enter. 3. Select the RAID set then press Enter. 4. When asked Are You Sure(Y/N)?, press Y to confirm. Resolving Conflicts When a RAID set is created, then metadata written to the disk includes drive connection information. If, after a disk failure, the replacement disk was previously part of a RAID set (or used in another system), it may have conflicting metadata. If so, this will prohibit the RAID set from being either created or rebuilt, in orde

ページ15に含まれる内容の要旨

BIOS Configuration The 6-Port SATA II 150 PCI Host Card w/RAID BIOS will appear every time your system starts up. If the BIOS doesn’t show, please try your controller in another PCI slot. During this (POST) process, the BIOS will show up and indicate the devices attached to it. Driver Installation For Windows® 2000 For A New Installation A new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the “UGT-ST310R\2000_XP_2003_Vi

ページ16に含まれる内容の要旨

to Windows. 2. At Found New Hardware Wizard, click Next. 3. Select Search for a suitable driver for my device (recommend) then click Next. 4. Insert the driver CD, check CD-ROM drives, uncheck the other boxes, click Next, then click Next again. 5. If the Digital Signature Not Found message appears, click Yes. Our driver has been thoroughly tested for stability and compatibility. 6. Click Finish. 7. Repeat steps 2-6. 8. Restart Windows to complete the driver installation. For Window

ページ17に含まれる内容の要旨

For An Existing Installation 1. Setup the RAID Array prior to driver installation and boot up to Windows. 2. At the Found New Hardware Wizard, select No, not this time, then click Next. 3. Insert the driver CD, select Install the software automatically (Recommended), and click Next. 4. Click Finish. 5. Restart Windows to complete the driver installation. For Windows® XP-x64/Server 2003-x64 For A New Installation A new installation requires a floppy disk for the driver installatio

ページ18に含まれる内容の要旨

1. Setup the RAID Array prior to driver installation and boot up to Windows. 2. At the Found New Hardware Wizard, select No, not this time, then click Next. 3. Insert the driver CD, select Install the software automatically (Recommended), and click Next. 4. Click Finish. 5. Restart Windows to complete the driver installation. For Windows® Vista For A New Installation A new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents o

ページ19に含まれる内容の要旨

3. Please insert driver CD, click Next. 4. Click Close to complete the installation. For Windows® Vista-x64 For A New Installation A new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the “UGT-ST310R\XP_2003_Vista\64bit” folder, found on the driver CD, onto a blank floppy disk then follow the directions below. 1. Setup the RAID Array prior to Windows installation. 2. Follow Microsoft’s Windows installation procedure. 3

ページ20に含まれる内容の要旨

2. Select Device Manager. 3. Double click SCSI and RAID Controller (Storage controllers), then double click Silicon Image SiI 3114 SoftRAID 5 Controller to display driver properties. A message this device is working properly is displayed in the dialog box, the driver has been correctly installed. SATA RAID 5 Management Software Installation For Windows® 2000/XP/Server 2003/Vista 1. Please insert the driver CD into your CD-ROM Drive. 2. At the Windows desktop click Start, then Run. 3


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Vantec 7.1 Channel PCIe Sound Card UGTS110 取扱説明書 コンピュータハードウェア 3
2 Vantec UGT-PC2S1P 取扱説明書 コンピュータハードウェア 1
3 Vantec FireWire 800 取扱説明書 コンピュータハードウェア 0
4 Vantec UGT-FW050 取扱説明書 コンピュータハードウェア 1
5 Vantec C128 取扱説明書 コンピュータハードウェア 0
6 Vantec MO3096Y6-1 取扱説明書 コンピュータハードウェア 0
7 Vantec FireWire 400 取扱説明書 コンピュータハードウェア 0
8 Vantec C133 取扱説明書 コンピュータハードウェア 0
9 Vantec UGT-PC210 取扱説明書 コンピュータハードウェア 0
10 Vantec UGT-IS100R 取扱説明書 コンピュータハードウェア 0
11 Vantec C123 取扱説明書 コンピュータハードウェア 0
12 Sony MSAKIT-PC4A 取扱説明書 コンピュータハードウェア 2
13 Sony MRW62E-S1 2694866142 取扱説明書 コンピュータハードウェア 5
14 Philips MATCH LINE 9596 取扱説明書 コンピュータハードウェア 17
15 Sony 64GB SDHC Class 10 Memory Card Readers SF32UY 取扱説明書 コンピュータハードウェア 1
16 Philips PSC702 取扱説明書 コンピュータハードウェア 1