ページ1に含まれる内容の要旨
ADV350B / ADV350S / ADV350P
DVD PLAYER WITH DROP-DOWN
VIDEO MONITOR
SOURCE
Installation Guide
ページ2に含まれる内容の要旨
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied. An LCD p
ページ3に含まれる内容の要旨
MATERIALS INCLUDED IN THIS PACKAGE: 1) ADV350 TV/Video Monitor with DVD (1pc) 2) 12 Pin Power / Signal harness (P/N 112-3483) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/ N 112B3143) (1 pc) 4) Hardware Package #4 x 3/8” Screws (9 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 5) Remote Control (1363855) (1pc) 6) PODTVT TV Tuner (P/N 136-3877) (1pc) (Optional) 7) SIRSWB Relay Box (P/N 112C3159) (1pc) (Optional)-See important note on previous page 8) Trim Ring (1pc) 9) Game C
ページ4に含まれる内容の要旨
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harness
ページ5に含まれる内容の要旨
VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is
ページ6に含まれる内容の要旨
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the video monitor is to be installed in a vehicle with the mini console, this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses. These screw bosses should contact the cross-member di- rectly (i.e.: no gap between
ページ7に含まれる内容の要旨
MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 12”x9”x3/4” Plywood Block (4) Self-Tapping Screws (not supplied) Mini-Console Video Unit (5) #8 Flat Washers (5) #8x3/4” Self-Tapping Screws -5-
ページ8に含まれる内容の要旨
ADV350 *ANTENNA FOR WIRELESS FM MOD See Antenna Note Below ** *OPTIONAL RELAY BOX SIRSWB UNIT (BACK VIEW) UNIT (BACK VIEW) CHOKE CHOKE Power Harness Power Harness Item #3 Item #3 TV TV To Secondary AV Monitor To Secondary AV Monitor ANTENNA ANTENNA RCA-Female RCA-Female INPUT INPUT 12 VDC Power and Ground 12 VDC Power and Ground VIDEO VIDEO TO TO TO TO OPTIONAL OPTIONAL OPTIONAL OPTIONAL LINE LINE Line Out-L (White) Line Out-L (White) ADDITIONAL ADDITIONAL ADDITIONAL ADDITIONAL Auxillary Auxil
ページ9に含まれる内容の要旨
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, b
ページ10に含まれる内容の要旨
Negative Switched Dome lighting Red / black - Lamp on To 12 pin Black / red - Lamp common connector Purple / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or -Verify that the correct so
ページ11に含まれる内容の要旨
128-7249A © 2005 ADVENT, 150 Marcus Blvd. Hauppauge, NY 11788
