ページ1に含まれる内容の要旨
USER’S GUIDE
COLOR MONITOR
Model No : 7cln
CTL
S/N:9978626503
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS FEDERAL COMMUNICATIONS COMMISSION 1. Read all of these instructions. 12. For added protection for this RADIO FREQUENCY INTERFERENCE STATEMENT monitor during a lightning storm, 2. Save these instructions for later use. or when it is left unattended and unused for long periods of time, 3. Unplug this monitor from the NOTE : This equipment has been tested and found to comply with the limits unplug it from the wall outlet. This wall outlet before cleaning. Do not for a Class
ページ3に含まれる内容の要旨
The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR Partner, Computer Technology Link, Inc. has determined that this product meets the Energy Star guidelines for energy efficiency.
ページ4に含まれる内容の要旨
CONTENTS INTRODUCTION Introduction ............................................................................. 1 This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s Product Features ................................................................. 2 guide carefully before installing your monitor, then keep it near your monitor for quick reference. Setup .................................................................
ページ5に含まれる内容の要旨
SETUP PRODUCT FEATURES INSTALLING THE TILT/SWIVEL STAND • The convenient and user-friendly on-screen display allows for easy and accurate adjustments of horizontal and vertical screen 1. Ensure that the power to the monitor is off. size and position, geometry and screen color. • The monitor supports a safe working environment in strict 2. Set the monitor face down with the underside facing you. compliance with the MPR II standard for low emissions. Pleas
ページ6に含まれる内容の要旨
CONNECTING THE SIGNAL CABLE AND POWER POWER MANAGEMENT SYSTEM CORD If you use the monitor with a computer that complies with the power-saving program, you can set the monitor to go blank when 1. Turn off the computer and monitor. the system has remained unused for a period of time. To specify the period or to disable this feature, set the system timeout field 2. Connect the 15 pin D-sub connector to the output port of the of the computer’s system setup program or use special software video card
ページ7に含まれる内容の要旨
OPERATION & ADJUSTMENT Key Process Control Panel ENGL SH DEUTSCH ESPAÑOL FRANCA S TAL ANO • Move cursor to the right window on the OSD window. • Increase the value of any selected function. • Move cursor to the left window on the OSD window. • Decrease the value of any selected function. • Launch OSD(On-Screen Display) MENU window. MENU • Move cursor to the high window on the OSD Start window. • Increase the value of V.size or V.center. • Move cursor to the low window on the OSD window. • D
ページ8に含まれる内容の要旨
OSD Functions ICON CONTROL FUNCTIONS ICON CONTROL FUNCTIONS Adjust the horizontal picture moire H. MOIRE cancellation. LANGUAGE Select language for OSD (5 languages). Adjust the vertical picture moire V. MOIRE cancellation. Adjust the position of the display H. CENTER & horizontally(left or right) and vertically V. CENTER (up or down). FOCUS Adjust the focus image. Choose different preset color COLOR TEMP temperatures or set your own customi
ページ9に含まれる内容の要旨
SPECIFICATIONS ICON CONTROL FUNCTIONS CDT Size 17-inch Display horizontal & vertical frequency Diagonal visible image area 16-inch STATUS and polarity. Dot Pitch 0.25 mm Synchronization Horizontal 30 - 95 KHz YES : VESA DPMS operation. POWER SAVER Vertical 50 - 160 Hz NO : NO DPMS operation. Plug and Play DDC1/2B/CI Display a RGB Color Bar to determine Power Saving EPA, VESA DPMS, Nutek Compliant TEST PATTERN whether the screen color is expressed Power Source 100-240 Va
ページ10に含まれる内容の要旨
DESCRIPTION FOR D-SUB CONNECTOR TROUBLESHOOTING Symptom Check Signal Pin No picture. Check if power switch and computer power switch Red 1 are in the on position. Green 2 Blue 3 Check if the signal cable is correctly connected to GND 4 the video card. GND 5 GND-Red 6 Check if the pins of D subconnector are not bent. GND-Green 7 GND-Blue 8 Check if the computer is in the power- saving mode. +5Vdc 9 GND-H.Sync 10 POWER LED is not Check if power switch is in the on position. GND-V.Sync 11 lit. Bi
