ページ1に含まれる内容の要旨
15D1 Touchcomputer User Guide
15D1 15-inch LCD Multi-function Touchcomputer
[Model 15D1]
ページ2に含まれる内容の要旨
Elo TouchSystems 15D1 Touchcomputer User Guide 15-inch Multi-function Touchcomputer Revision A P/N E674343 Elo TouchSystems 1-800-ELOTOUCH (1-800-356-8682) www.elotouch.com
ページ3に含まれる内容の要旨
Copyright © 2009 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems ma
ページ4に含まれる内容の要旨
Table of Contents Chapter 1: Setup......................................................................................1 Unpacking Your Touchcomputer ....................................................................................................1 Adjusting the Display ......................................................................................................................2 Setting Up the Operating System.................................................................
ページ5に含まれる内容の要旨
Chapter 6: Technical Support...............................................................39 Technical Assistance......................................................................................................................39 Regulatory Information............................................................................41 Warranty ...................................................................................................44 Index.......................................
ページ6に含まれる内容の要旨
C H A P T E R 1 SETUP This chapter discusses how to set up and test your touchcomputer. For information on peripheral options, refer to Chapter 3, “Options and Upgrades.” Unpacking Your Touchcomputer Check that the following items are present and in good condition: Power cable US/Canada Power cable Europe Touchcomputer Recovery DVD and Advertising Optional Quick Install Guide brackets security screw 15D1 TOUCHCOMPUTER USER GUIDE 1
ページ7に含まれる内容の要旨
Adjusting the Display The display screen can be adjusted from 0 to 60 degrees, as shown below. CAUTION: To protect the LCD, be sure to hold the base when adjusting the display, and take care to not touch the screen. Setting Up the Operating System The initial setup of the operating system takes approximately 5-10 minutes. Additional time might be needed for different touchcomputer hardware configurations and connected devices. To set up the Windows OS for the touchcomputer, turn
ページ8に含まれる内容の要旨
3. Click Customize. The Regional and Language Options window appears. Select the Languages tab. 4. If required, check the boxes for “Install files for complex script and right-to-left languages” and “Install files for East Asian languages.” 5. Select the Regional Options tab. 6. Select your preferred language from the drop-down list in the Standards and formats pane. 15D1 TOUCHCOMPUTER USER GUIDE 3
ページ9に含まれる内容の要旨
7. Click Apply. 8. Select your location from the drop-down list in the Locations pane. 9. Click OK. 15D1 TOUCHCOMPUTER USER GUIDE 4
ページ10に含まれる内容の要旨
Selecting the Time Zone When the following window appears, you can change the time zone, date, and time of the touchcomputer. After making any changes, click Next to finish. Windows Setup completes the installation of the touchcomputer. Testing Peripherals The touchcomputer can be configured with several different optional peripherals, such as a MSR or cash drawer. To test an optional peripheral that is installed on the touchcomputer, refer to the instructions in Chapter 3, “Options
ページ11に含まれる内容の要旨
Click the Align button. This launches the calibration program. The window shown below opens. Follow the instructions to calibrate the touchscreen. 15D1 TOUCHCOMPUTER USER GUIDE 6
ページ12に含まれる内容の要旨
Securing the Base There are two mounting options for the 15D1 touchcomputer. In both cases, the base must be mounted on a horizontal surface. • Option 1: Secure from below. Use the four pretapped holes to secure the touchcomputer from below the mounting surface. The holes are designed to work with ISO metric m6 screws. These screws are not contained in the package, but should be readily available at any hardware store. • Option 2: Secure from top. Use the two through holes to secure th
ページ13に含まれる内容の要旨
To install these brackets, simply push them onto the sides of the back door of the 15D1 touchcomputer, as shown in the figure below. Then insert the advertising material as shown below. 15D1 TOUCHCOMPUTER USER GUIDE 8
ページ14に含まれる内容の要旨
C H A P T E R 2 OPERATION This chapter describes how to control the On-Screen Display (OSD), power buttons, and I/O panel. All adjustments made to the OSD and power controls are automatically saved. User settings remain unchanged after powering off/on or in the case of a power failure. 3 4 5 6 7 8 9 1 1. HDD status LED 2 2. Computer power LED 3. Head power LED 4. Touch power LED 5. Menu button 6. Left button 7. Right button 8. Select button 9. Power ON/OFF button
ページ15に含まれる内容の要旨
On-Screen Display (OSD) OSD Menu 1. To display the OSD Menu, press the Menu button. Press the RIGHT button or LEFT button to toggle and the SELECT button to select from the different OSD sub-menus and functions. 2. When the function you want to change is shown, press the SELECT button. 3. To adjust the value of the function: 4. Pressing the RIGHT button increases the value of the selected OSD control option. 5. Pressing the LEFT button decreases the value of the selected OSD control
ページ16に含まれる内容の要旨
Feature Description Language Changes language to English, French, Italian, German, Spanish, Japanese, Simplified Chinese, or Traditional Chinese. Recall Sets color recall and recall defaults. Restores original factory settings. Miscellaneous Adjusts sharpness, enables/disables DDCCI function. • Sharpness: Adjusts sharpness of video. Exit Exits the OSD. OSD and Power Button Control The OSD menu and power button are enabled by default. To enable or disable the OSD function: 1. Simult
ページ17に含まれる内容の要旨
Head Power Status LED The head power status is indicated by a different LED, which is located at the lower edge of the head (#3 in figure on page 9). LED Color to Observer State Off No input power to head — Off mode Red Input power present, power switch off — Off mode Amber Input power present — Sleep mode Green Input power present — On mode Touch Power Status LED The touch power status is indicated by a separate LED located at the lower edge of the head and to the right of the Head
ページ18に含まれる内容の要旨
Using the Input/Output Panel To access the input/output (I/O) ports, open the cable cover door on the left side of the unit, as shown below. Optional security screw Opening for cables The touchcomputer provides a number of input and output interfaces for connecting a wide variety of compliant devices as shown in the following figure. 15D1 TOUCHCOMPUTER USER GUIDE 13
ページ19に含まれる内容の要旨
1 8 9 2 10 3 11 12 4 13 5 14 6 7 15 15D1 TOUCHCOMPUTER USER GUIDE 14
ページ20に含まれる内容の要旨
Number Port Description 1 Audio Audio in (left), out (center), mic (right) • Audio In • Audio Out: One 3.5mm stereo audio output jack for connecting headphones or external powered speakers • Microphone Input: One 3.5mm microphone input jack for connecting an external microphone 2 Ethernet One RJ45 Ethernet port providing LAN capabilities 3, 8, 9 USB Seven USB 2.0 type A ports 4 VGA One D-SUB VGA output port for connecting the display head 5 Parallel Standard 25-pin connector port
