ページ1に含まれる内容の要旨
Fujitsu TE988G user manual
Table of Contents
FCC Information 1
Energy Declaration 1
Important Safeguards 2
Installation 3
Monitor Connection 4
Pin Assignment 4
Operation and User Adjustment 5
On-Screen Display Guide 6
Specifications 13
Trouble-Shooting 14
ページ2に含まれる内容の要旨
Fujitsu TE988G Color Monitor FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful
ページ3に含まれる内容の要旨
Fujitsu TE988G Color Monitor Important Safeguards 1. Follow all warnings and instructions marked on the video monitor. 2. Do not use attachments which is not recommended by the video monitor manufacturer as they may cause hazards. 3. Do not expose the monitor to rain, water, moisture or direct sunlight. 4. Do not place near or over a radiator or other heat-generating equipment. 5. Do not place this video monitor on an unstable cart, stand or table. The video monitor may fall
ページ4に含まれる内容の要旨
Fujitsu TE988G Color Monitor change without notice. 3
ページ5に含まれる内容の要旨
Fujitsu TE988G Color Monitor Installation Tilt Swivel & Base 1. Turn the monitor upside down. 2. Turn the base upside down. Insert its four hooks into the four slots on the bottom of the monitor. (Point the hooks on the base toward the front of the monitor) Figure 1 3. Push the tilt swivel and base in the direction of arrow (!) as indicated in Figure 2 to lock the hooks. Figure 2 4
ページ6に含まれる内容の要旨
Fujitsu TE988G Color Monitor Monitor Connection To attach the monitor to your system, follow the steps as described below: 1. Turn off the monitor and computer. 2. Connect one end of the power cable to your monitor and the other end to the power outlet. 3. Connect the 15-pin D-Sub signal cable to the video adapter output on your personal computer. 4. Turn on the monitor and the computer. Wait about 30 seconds to adjust the picture with the adjustment contro
ページ7に含まれる内容の要旨
Fujitsu TE988G Color Monitor Operation and User Adjustment Control Panel Figure 4 shows the position of following operating units: 1. Power ON / OFF Switch 2. Power LED 3. Menu – Displays OSD menu & Scrolls through OSD menu 4. Function Control Key – Adjust level of selected items 6
ページ8に含まれる内容の要旨
Fujitsu TE988G Color Monitor On-Screen Display Guide 1. Contrast & Brightness (1).Press either 5 or 66 to activate and make the contrast adjustment shown by the OSD 66 parameter. The parameter moves rightward indicating contrast increase and leftward indicating contrast decrease. 63 Figure5 Contrast Adjustment Parameter (2). Press either3or4 to activate and make the brightness adjustment shown by the OSD
ページ9に含まれる内容の要旨
Fujitsu TE988G Color Monitor A B C 52 D H-Phase/V-Center E F Figure 7 Function Menu A. OSD contains 10 icons representing the following function adjustments: H-Phase/V-Center, H-Size/V-Size, Pincushion/Trapezoid, Pin Balance/Corner, Parallel/Tilt, RGB-Gain, OSD Position, Language, Tool and Exit. B. Hand-shaped pointer indicates the current function selected. C. There are four adjustments for each function s
ページ10に含まれる内容の要旨
Fujitsu TE988G Color Monitor ( 1 ). H-Phase & V-Center function window Press 3 or 4 key to reposition the picture leftward or rightward. Press 5 or 6 key to reposition the picture upward or downward. ( Please refer to the figure 7 ) ( 2 ). H-size & V-size function window H-Size/V-Size Press 3 key to reduce the H-size and press 4 key to enlarge the H-size. Press 5 to enlarge the V-size and press 6 key to reduce the V-size. ( 3 ). Pincushion & Trapezoi
ページ11に含まれる内容の要旨
Fujitsu TE988G Color Monitor ( 4 ). Pin - Balance & Corner function window PinBalance/Corner Press either 3or 4 to adjust pin balance. Press eitheru ort to adjust corner distortion. ( 5 ). Parallelogram & Tilt function window Parallel/Tilt Press either 3or4to adjust parallelogram. Press eitheru or t to adjust tilt. 10
ページ12に含まれる内容の要旨
Fujitsu TE988G Color Monitor ( 6 ). RGB Color Temperature function window. 63 30 12 /7500¢ K X 9300¢ K/Us X er R-Gain RGB Value Setting The current setting of the color temperature is presented in purple. Press 5or6key to scroll the black bar up or down to your desired item. There are three factory settings available for 0 0 0 selection: 6500 K , 7500 K, and 9300 K. For personal preference, you may directly adjust 0 0 0 the RGB values separately either in the User’s mode or in 6500
ページ13に含まれる内容の要旨
Fujitsu TE988G Color Monitor ( 8 ). Language function window Press uort to select your desired language, and then the OSD menu will be presented in the language selected. Note : No message will be displayed if you select “None”. ( 9 ). Tools function window. None Recall 1. Recall factory setting if monitor H-V frequency is in preset mode . including Phase, Size, and Pincushion/Key-stone. 2. Adjust OSD countdown timer whose duration range
ページ14に含まれる内容の要旨
Fujitsu TE988G Color Monitor Note 1. Degauss User need to perform manual degaussing , once display monitor is turned to other direction. It's recommended to wait 15 minutes before user to make next degaussing activity , no matter auto or manual degaussing was performed last time. 2. The icon, a cup of coffee, will appear to remind you to take a break. 3. The duration for displaying tea time is about 20 seconds. You may also set the duration For displaying tea time acc
ページ15に含まれる内容の要旨
Fujitsu TE988G Color Monitor Specifications 0 CRT SIZE 19" diagonal, 90 deflection Viewable area 18" Dot pitch 0.26mm Video: Analog (0.7Vp-p/1.0 Vp-p, 75 ohm positive) Input Signal Selected by OSD Control Sync : Separate sync, positive or negative TTL Input Connector 15-pin D-connector Scanning Horizontal:30KHz-95KHz frequency Vertical: 50Hz-150Hz Active Display Area Horizontal: 350 mm ( adjustable ) Vertical: 262 mm ( adjustable ) Resolut
ページ16に含まれる内容の要旨
Fujitsu TE988G Color Monitor Trouble Shooting If you are experiencing difficulties with your monitor, check following table for possible solutions. Problem Items to check No picture 1. The VGA card should be completely seated in the slot. ? 2. Power switch of the monitor and the PC should be in the ON position. 3. The signal cable should be completely connected to the video card / computer. 4. Check if the pins of the connector are twisted or shrunk. ? Image is scrolling or
