ページ1に含まれる内容の要旨
HP TFT7600 Rackmount Keyboard and Monitor
User Guide
November 2005 (First Edition)
Part Number 365378-001
ページ2に含まれる内容の要旨
© Copyright 2005 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. November 2005 (First Edition) Part Number 365378-001 Audience
ページ3に含まれる内容の要旨
Contents Introduction.................................................................................................................................. 5 Introduction .............................................................................................................................................. 5 TFT7600 RKM features............................................................................................................................... 5 Components .....................
ページ4に含まれる内容の要旨
Disposal of waste equipment by users in private households in the European Union......................................... 26 Power cord requirement ........................................................................................................................... 26 Power cord statement for Japan................................................................................................................. 26 Electrostatic discharge..................................................
ページ5に含まれる内容の要旨
Introduction In this section Introduction ............................................................................................................................................. 5 TFT7600 RKM features ............................................................................................................................. 5 Components ............................................................................................................................................ 6 Rear
ページ6に含まれる内容の要旨
Feature Description Monitor input Plugs into a standard VGA connector; does not require a special graphics adapter card Plug and Play Plug-and-Play capability if supported by your system OSD Available in seven languages: • English • French • German • Italian • Japanese • Simple Chinese • Spanish Keyboard with Three button touchpad with scroll bar touchpad Power supply 12v DC/30 Watt Scroll keys Four scroll keys (inverted T) Components Reference number Component Func
ページ7に含まれる内容の要旨
Reference number Component Function 4 OSD activation button • Launches OSD menus • Selects • Exits menus and OSD 5 Scroll lock LED 6 Cap lock LED 7 Number lock LED 8 Touchpad 9 Left pick button 10 Middle pick button 11 Right pick button 12 Scroll bar 13 USB pass thru Pass thru to the rear USB port (callout 1 in the following figure) Rear components Reference number Component Function 1 USB pass thru Connects to a KVM switch virtual media port 2 USB Keyboar
ページ8に含まれる内容の要旨
Installation In this section Installing the TFT7600 RKM....................................................................................................................... 8 Kit contents.............................................................................................................................................. 8 Installing the HP TFT7600 RKM.................................................................................................................. 8 Accessing the
ページ9に含まれる内容の要旨
NOTE: If the HP 1U Adjustable Toolless Rails do not snap into place, be sure that they align with the holes marked on the rack. The holes marked on the rack must be in the same location for the front and rear of the rack. 2. Extend the inner slides until they lock into place. 3. Align the unit with the extended inner slides, inserting the unit into the rack. Installation 9
ページ10に含まれる内容の要旨
4. Slide the brace rail assembly in between the HP 1U Adjustable Toolless Rails from the rear of the rack. 5. Align the screw holes on the brace rail with the screw holes on the HP 1U Adjustable Toolless Rails. 6. Secure the brace rail to the HP 1U Adjustable Toolless Rails with two 6-32 screws. Installation 10
ページ11に含まれる内容の要旨
7. Remove the two shipping screws from the rear of the HP TFT7600 and discard the screws. 8. Attach the cable management arm to the rear of the unit with two 6-32 screws, supplied in the kit. Installation 11
ページ12に含まれる内容の要旨
9. Connect and route the cables through the cable management arm and unit opening. Installation is complete. Accessing the TFT7600 RKM 1. Gently extend the TFT7600 RKM until the slides lock. 2. Push the display release latch then lift the display. Removing the HP TFT7600 RKM To remove the TFT7600 RKM, reverse the order of the steps listed in the Installing the HP TFT7600 RKM (on page 8) section. Installation 12
ページ13に含まれる内容の要旨
Removing the HP 1U Adjustable Toolless Rails 1. Locate the spring release. 2. Place your hand on the outside of the HP 1U Adjustable Toolless Rails so that you can move the spring release. 3. Gently move the spring release toward the inside of the rack (1) while moving the HP 1U Adjustable Toolless Rails out toward you and away from the rack (2). NOTE: If you cannot gain access to the spring release from the outside of the HP 1U Adjustable Toolless Rails, a tool might be required to
ページ14に含まれる内容の要旨
2. Slide it back to release the locking mechanism and gently pull to remove the cable. Installation 14
ページ15に含まれる内容の要旨
Operational overview In this section On-screen display .................................................................................................................................. 15 Launching OSD menu ............................................................................................................................. 15 Navigating OSD.................................................................................................................................... 16 OSD me
ページ16に含まれる内容の要旨
3. Press the OSD activation button again to select your choice. A second level will expand menu items. Navigating OSD To navigate through the OSD menus and functions: • Use the Up (+) or Down (-) button to scroll through the OSD menu or an OSD sub-menu. The Up (+) and Down (-) button are also used to adjust or change a function setting. • Use the OSD activation button to select a sub-menu or a function. Example: To exit the OSD menu: 1. Press the Down (-) button to scroll to the Exit
ページ17に含まれる内容の要旨
The center of the bar is obtained from the factory-preset value for Horizontal Position. At value=MIN, the selection of + positioning response might vary between XGA and SXGA panels. This is caused by physical limitations at MIN OSD placement. Vertical position The V position option displays a slider bar to enable the adjustment of the screen's vertical position. The center of the bar is obtained from the factory-preset value for Vertical Position. Clock The Clock option displays a
ページ18に含まれる内容の要旨
Auto Configuration The Auto Configuration option performs four functions automatically: • Auto Level—Automatically adjusts the black and white levels of the screen • Auto Position—Automatically adjusts the position of the screen • Auto Phase—Automatically adjusts the phase • Auto Clock—Automatically adjusts the output clock per line to match the input Factory settings The Factory settings option enables the user to set the HP TFT7600 back to its original factory settings. The followi
ページ19に含まれる内容の要旨
Maintenance In this section Maintenance and shipping guidelines ...................................................................................................... 19 Shipping the TFT7600 RKM..................................................................................................................... 20 Moving a rack with the TFT7600 RKM installed ......................................................................................... 20 Maintenance and shipping guidelines T
ページ20に含まれる内容の要旨
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substance to clean the monitor screen or cabinet. These chemicals might damage the monitor. Never use water to clean an LCD screen. Shipping the TFT7600 RKM Keep the original packing box in a storage area in case you must move or ship your RKM. Moving a rack with the TFT7600 RKM installed When moving the TFT7600 RKM installed in a rack, HP recommends that you install the lock plates, included in your kit, on each side
