ページ1に含まれる内容の要旨
QUAD FULL HIGH DEFINITION MONITOR
MODEL
56P-QF60LCU
USER'S MANUAL
Be sure to follow the directions below.
This product requires special installation to prevent
falling or toppling.
Warning:
Please ask installation specialists for installation.
Don't attempt to install the product by yourself.
This user's manual is important to you. Please read it before using your product.
ページ2に含まれる内容の要旨
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning fl ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi cient magnitude to constitute a risk of electric shock. The exclamation point within an
ページ3に含まれる内容の要旨
Important safeguards Please read all these instructions regarding your monitor and 10. Power sources retain them for future reference. Follow all warnings and instruc- This product should be operated only from the type of power tions marked on the monitor. source indicated on the marking label. If you are not sure of the type of power, please consult your appliance dealer or 1. Read instructions local power company. All the safety and operating instructions should be read be- 11. Power-cord
ページ4に含まれる内容の要旨
WARNING: CAUTION: Unplug immediately if there is something wrong with Battery replacement of the optional remote control • Improper use may result in fi re, injury, or spread dirt due to your product. Do not operate if smoke, strange noise or odor comes out of leakage, heat generation, or explosion. your product. It might cause fi re or electric shock. In this case, • Replace all the batteries with new ones. Use two AAA unplug immediately and contact your dealer. batteries (R03). • Load the batt
ページ5に含まれる内容の要旨
COMPLIANCE NOTICE OF FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio comm
ページ6に含まれる内容の要旨
Parts Name and Functions Front panel EXIT MENU (7) (6) (5) (4) (3) (2) (1) (8) (1) POWER button ( ) (7) EXIT button Switches the power on/off. Acts as EXIT button to move to previous menu with menu. (2) MENU button (8) Remote control sensor and power lamp Activates the menu when the menu is turned-off. Receives the signal from the remote control (when using the optional wireless remote control). During start-up, it will blink (3) PLUS (+) button green. Glows red when the LCD is in stand-by mod
ページ7に含まれる内容の要旨
Rear panel DVI-D POWER INPUT1 INPUT2 INPUT3 INPUT4 RS-232C LAN (1) (2) (3) (4) (5) (1) Main Power Switch (4) RS-232C connector On/Off Switch to turn main power on/off. Connect the RS-232C cable with the RS-232C connector of the computer for control the monitor. (2) AC IN connector Connects with the power cord. (5) LAN connector Connect the LAN cable with the LAN connector of the com- (3) INPUT 1 - 4 (DVI-D x 4) puter for control the monitor. Connect the DVI-D cable with the DVI-D connector of t
ページ8に含まれる内容の要旨
Installation To avoid monitor from falling Take measures to prevent the monitor from falling over in case Warning: of an earthquake or other disaster to lessen the probability of injury and damage resulting from fall. Be sure to follow the directions below. As shown in the fi gure, secure the monitor to a solid wall or pil- lar using rope (commercially available) strong enough to bear This product requires special installation the weight of the monitor. (Approx. 51 kg) to prevent falling or t
ページ9に含まれる内容の要旨
Connections Before making connections: • First turn off the power of all the attached equipment and make connections. • Refer to the user manual included with each separate piece of equipment. DVI-D cable DVI-D Computer 56P-QF60LCU (Rear panel) DVI-D INPUT1 INPUT2 INPUT3 INPUT4 Recommended video signal timing for this product is as follows. Resolution Frequency Notes Horizontal Vertical 1920×1080 67.5 kHz 60 Hz Each of INPUT 1 to 4 connectors • To display images at a resolution of 3840x2160, i
ページ10に含まれる内容の要旨
Basic operation Power ON procedures 1. Turn the Main Power Switch on the rear of the product to ON to turn on the main ON power. OFF The power lamp blinks green and then illuminates red. (You cannot turn on the power Main Power Switch while the lamp is blinking green.) (Rear panel) 2. Press the power ( ) button to turn on the power. The power lamp illuminates green. 3. Turn on the power of the other equipment. CAUTION: This monitor has the sensors to detect errors in the power, fan, temper
ページ11に含まれる内容の要旨
Troubleshooting Consult the following table for troubleshooting a problem. Symptom Cause and remedy Reference page The monitor displays nothing. (The power lamp doesn't Check that the power cord is connected securely. P.9 illuminate.) Using other device, check that the wall outlet is receiving - power. Check that the main power switch isn't off. P.7 The monitor displays nothing. (The power lamp is blinking An error may have occurred. Contact your MITSUBISHI - red.) dealer. Blinking red 0.5 s
ページ12に含まれる内容の要旨
Specifi cations Model 56P-QF60LCU Surface treatment Glare Diagonal 56.2” (142.75 cm) Viewable size 1244.16 × 699.84 mm Resolution 3840 × 2160 Pixel pitch 0.108(H) × 0.324(V) Color 16,770,000 *1 View angle (Typ.) 88° (Up and Down), 88° (Left and Right) 2 Brightness (Typ.) 500 cd/m Contrast ratio (Typ.) 1200 : 1 *2 Response speed (Typ.) GTG 6.5 ms Input resolution 1920 × 1080 Horizontal frequency 67.5 kHz Vertical frequency 60 Hz PC input Video input Digital RGB Sync Separate HV sync :
ページ13に含まれる内容の要旨
Pin Assignment 1) INPUT 1 - 4 PIN No. Name PIN No. Name 1 TX 2- 13 NC DVI-D 24-pin 2 TX 2+ 14 +5V Power 3 Shield (TX2/TX4) 15 Ground 1 8 4 NC 16 Hot Plug Detect 5 NC 17 TX 0- 6 DDC-Serial Clock 18 TX 0+ 9 16 7 DDC-Serial Data 19 Shield (TX0/TX5) 8NC 20 NC 9 TX 1- 21 NC 10 TX 1+ 22 Shield (TXC) 17 24 11 Shield (TX1/TX3) 23 TXC + 12 NC 24 TXC - 2) RS-232C input/output Pin No Name D-SUB 9P 1NC 2 RXD 1 5 3 TXD 4NC 5 GND 6NC 7RTS 8 CTS 6 9 9NC 3) LAN terminal Pin No Name 18 1 TX+ 2 TX- 3 RX+ 4NC 5NC
ページ14に含まれる内容の要旨
MITSUBISHI ELECTRIC CORPORATION 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan 871D502A10 Printed in Japan
