ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Index Warning.................................................................................................. 1 Contents ............................................................................................... 2 Quick Start ...........................................................................................3 Controls ................................................................................................ 5 Recommended Use ..................................................
ページ3に含まれる内容の要旨
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
ページ4に含まれる内容の要旨
Contents ® Your new NEC MultiSync FP2141SB monitor box* should contain the following: • MultiSync FP2141SB with tilt/swivel base • Power Cord • Signal Cable (D-Sub to D-Sub) • USB Cable • User’s Manual Signal Cable USB Cable User’s Manual Power Cord * Remember to save your original box and packing material to transport or ship the monitor. 2
ページ5に含まれる内容の要旨
Quick Start To attach the FP monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the graphics card into your system. For more information, refer to the graphics card installation manual. 3. For the PC: Connect the 15-pin mini D-SUB connector of the signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync Macintosh cable adapter (not included) to the monitor
ページ6に含まれる内容の要旨
Quick Start –continued Power Cord Figure C.1 Figure D.1 4
ページ7に含まれる内容の要旨
Controls ™ OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: Main Menu Sub-Menu EXIT Exits the OSM menu. Exits to the OSM controls main menu. Note : Deactivates the OSM menu and activates the OSM menu when the OSM is turned off. CONTROL Moves the highlighted Moves the highlighted area area left/right to select left/right to select one of the one of the sub-menu. controls. Note : When the OSM menu is off, it acts as a Hot key for Brightness. CONTROL Has no f
ページ8に含まれる内容の要旨
Controls –continued Size and Position Controls Auto Adjust: Automatically adjust the horizontal and vertical size and position settings for the applicable timing signal. NOTE: Auto Adjust is unavailable with no image signal or narrow size of image signal input. Left/Right: Moves the image horizontally (left or right). Down/Up: Moves the image vertically (up or down). Narrow/Wide: Decreases or increases the horizontal size of the image. Short/Tall: Decreases or increases the vertical size of th
ページ9に含まれる内容の要旨
Controls -continued Linearity: This selection allows you to adjust the spacing of the area on the screen. The purpose of this control is to ensure that a one-inch circle is a true one-inch circle wherever it is on the screen. The best way to determine the vertical linearity is as follows: • Draw equally spaced horizontal lines using a drawing application that has a ruler. • Use the Vertical Balance control to adjust the lines near the top and bottom of your screen. • Use the LINEARITY (VER.) con
ページ10に含まれる内容の要旨
Controls –continued ™ Factory Preset: Selecting Factory Preset allows you a reset most OSM control settings back to the factory settings. A warning statement will appear to confirm that you do want to reset ALL settings. Individual settings can be reset by high- lighting the control to be reset and pressing the RESET button. Information Display Mode: Indicates the current mode and frequency setting of the monitor. Monitor Info: Indicates the model and serial numbers of your monitor. Refresh No
ページ11に含まれる内容の要旨
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC FP2141SB COLOR MONITORS: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the
ページ12に含まれる内容の要旨
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 24 inches. • Rest your eyes periodi
ページ13に含まれる内容の要旨
Recommended Use –continued • Use the preset Color Setting and Sides Left/Right controls • Use non-interlaced signals with a vertical refresh rate between 75-160Hz • Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient contrast For more detailed information on setting up a healthy work environment, write the American National Standard for Human Factors Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard N
ページ14に含まれる内容の要旨
Specifications ® ™ Monitor MultiSync FP2141SB Notes Specifications Monitor Picture Tube Diagonal: 22 inch/55 cm 90° deflection, 0.24 mm grille pitch, Viewable Image Size: 20 inch/508 mm medium short persistence phosphor, Radius: 50000 mm aperture grille CRT, G-WARAS coating Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Negative) (TTL Level) Sync on Green video (Positive) 0.7Vp-p and
ページ15に含まれる内容の要旨
Features Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is what you get on your printed output. The striped phosphor alignment of the CRT delivers superior vertical definition with improved brightness for more uniform image contrast. ® OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Dual
ページ16に含まれる内容の要旨
Features –continued Constant Brightness: sustains the brightness and screen color levels consistently over the normal life of the monitor. SB (Super Brightness) Mode: Provides the screen brightness suitable for the screen images displayed. Super Bright Mode OFF: for text based images (normal use) Super Bright Mode-1 ON: for images Super bright Mode-2 ON: for moving image such as DVD movies USB Hub: Self-powered hub with 1 upstream port and 4 downstream ports. 14
ページ17に含まれる内容の要旨
Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments
ページ18に含まれる内容の要旨
Troubleshooting –continued Attention message displayed • Check the inputted signal. NOTE:The attention message may display when power on the MultiSync monitor. In case that the attention message disappear after in a little while, there is no problem at the inputted signal. Self check function • Press any control button on the front of monitor when you see a problem on the screen. - In case that all R, G and B colors are seen in the diagnosis message, the MultiSync monitor has no problem. In ca
ページ19に含まれる内容の要旨
References NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support: (800) 632-4662 Fax: (800) 695-3044 Parts and Accessories/Macintosh Cable Adapter: (888) NEC-MITS [888-632-6487] Customer Service Policies & Processes: http://www.necmitsubishi.com/ css/ServicePolicies/ServicePolicies.htm Online Technical Support Knowledge Base: http://www.necmitsubishi.com/ css/knowledgebase.cfm Customer Service & Technical Support Email: http://www.necmitsubishi.com/
ページ20に含まれる内容の要旨
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and wil
