ページ1に含まれる内容の要旨
SIGNAL A/B SELECT
ADJUST
- +
OSD OFF
AUTO-SCANNING WITH DIGITAL CONTROL
LCD COLOR DISPLAY MONITOR
® ™
MultiSync LCD1800
USER’S GUIDE
For future reference, record the serial
number of your display monitor in the
space below:
Internet Home Page: http://www.necmitsubishi.com/
SERIAL No.
The serial number is located on the
Supplying Windows 95/98 INF File download service,new products
rear cover of the monitor.
information, etc.
ページ2に含まれる内容の要旨
As an ENERGY STAR Partner, NEC-MITSUBISHI RADIO INTERFERENCE REGULATIONS STATE- Electronics Display of America, Inc. has determined MENT FOR U.S.A. that this product meets the ENERGY STAR guide- lines for energy efficiency. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment g
ページ3に含まれる内容の要旨
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet, using the address: Congratulations! http://www.tco-info.com/ You have just purchased a TCO’99 approved and labelled product! Your choi
ページ4に含まれる内容の要旨
ENGLISH CONTENTS 1. INTRODUCTION .................................................. 1-2 1.1 Features ..................................................... 1-2 1.2 Internal Preset Memory Capability ............. 1-2 ™ 1.3 IPM (Intelligent Power Manager) System . 1-3 1.4 DDC ........................................................... 1-3 CAUTION 1.5 Display Mode Selection ............................. 1-3 1.6 Auto Adjustment Function .......................... 1-3 Do not remove the monitor cabinet
ページ5に含まれる内容の要旨
1 INTRODUCTION 1 ™ FullScan Capability Congratulations on your purchase of the MultiSync ™ Allows you to use the entire screen area in most LCD1800 high resolution color LCD monitor. resolutions, significantly expanding image size. This guide tells you how to connect, adjust and care for your MultiSync LCD1800 monitor. This guide also pro- VESA Standard Mounting Interface vides technical specifications and instructions for trouble- Allows users to connect their MultiSync monitor to any shootin
ページ6に含まれる内容の要旨
ENGLISH ™ 1.3 IPM (Intelligent Power Manager) System 1.6 Auto Adjustment Function ("AUTO ADJUST" P1-10) The monitor has a IPM(Intelligent Power Manager) Sys- tem which reduces the power consumption of the monitor This function is to adjust "CLOCK PHASE" automatically when not in use. and periodically (once per 30 min.) against changes of the signal condition or ambient temperature and to adjust When the horizontal sync signal and/or vertical sync signal "CLOCK PHASE", "HORIZONTAL POSITION"
ページ7に含まれる内容の要旨
- + ® 1.10 AccuColor Control Function 1.13 Unpacking The following color modes are available: After you unpack the box you should have all of the items 1. sRGB: sRGB mode dramatically improves the color indicated in Figure 1. Save the box and packing materials fidelity in the desktop environment by a single stan- in case you ship or transport the monitor. dard RGB color space. With this color supported environment, the operator could easily and confi- dently communicates color without further
ページ8に含まれる内容の要旨
ENGLISH 1.15 Quick Operation Chart To summarize the steps in connecting your computer and ™ adapter with MultiSync LCD1800 color LCD monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the MultiSync LCD1800 color LCD monitor and the signal cable between the MultiSync LCD1800 and the computer. Turn on the monitor. Turn on the computer. Set the controls and switches. If a problem appears. OK OK See 6. TROUBLESHOOTING If the problem persists.
ページ9に含まれる内容の要旨
2 PART NAME 2 2.1 Control Names See Figures 3 and 4 for the location of the user controls, indicator and connectors. Each part is identified by number and described individually. REAR FRONT - + SIGNAL A/B SELECT ADJUST + - Figure 4 OSD OFF Figure 3 2.2 Function CABLE COVER (UPPER) POWER SWITCH: A push-on / push-off switch for power input. CABLE COVER (LOWER) POWER-ON INDICATOR: This indicator illumi- DC POWER CONNECTOR nates when power is on. SIGNAL A/B and OSD OFF BUTTON: This button SIGNAL I
ページ10に含まれる内容の要旨
ENGLISH 3 INSTALLATION AND 3 CONNECTION 3.2 Signal Cable Connection On the back of the monitor are three plug-in connec- tions: one for the DC power connection and others for The attached video signal cable provides a D-SUB-15P the video signal connection. connector for the VGA compatible analog RGB outputs on your computer. Apple Macintosh Computers can also be 3.1 AC Power Connection interfaced using the optional Macintosh adapter. Remove the cable covers. The DC jack from the AC • The Sync
ページ11に含まれる内容の要旨
3.2.2 Connecting to An Apple Macintosh Computer Figure 6 shows the signal cable and Macintosh Adapter to the video port in an Apple Macintosh. 1. Power off, both the monitor and the computer. 2. Connect the 15-pin (D-SUB-15P) end of the Macintosh Adapter to the straight 15-pin connector on the Macintosh video port on the computer or on the video board. 3. Connect the sub-miniature 15-pin (D-SUB-15P) end of the Macintosh Adapter to the signal cable. 4. Power on the monitor, then the Macintosh. 5.
ページ12に含まれる内容の要旨
ENGLISH 4 AUTO SETUP 4 5 OSM(On Screen Man- 5 FUNCTION ager) FUNCTIONS ™ Two methods, "AUTO SETUP" and "OSM Adjustment" How to Adjust the Screen are available for adjusting the screen. (For the "OSM Adjustment", see 5. OSM (On Screen Manager) FUNC- The monitor has an OSM (On Screen Manager) function. TIONS.) Conduct the "AUTO SETUP" first. And then, do The following procedure shows how to adjust the screen the "OSM Adjustment" if necessary. with using the OSM function. The “AUTO SETUP” is to
ページ13に含まれる内容の要旨
5.1 Adjustment Items Press "ALL RESET" to restore to the factory preset level. Press and buttons together, to restore to the factory preset level. Set data by each timing. Set data does not change by the changing of the signal timing. Press the Minus Button: Press the Plus Button: Group Item Item Icon Icon To decrease the To increase the BRIGHTNESS brightness. brightness. To decrease the con- To increase the con- CONTRAST trast. trast. To be deep of black To be light of black B
ページ14に含まれる内容の要旨
ENGLISH Press "ALL RESET" to restore to the factory preset level. Press and buttons together, to restore to the factory preset level. Set data by each timing. Set data does not change by the changing of the signal timing. Group Item Press the Minus Button: Press the Plus Button: Item Icon Icon To restore to the fac- ALL RESET tory preset mode. To move the OSD position for 5 places. OSD POSITION To select the constant To select the power POWER SAVE power mode. save mode. To off
ページ15に含まれる内容の要旨
Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the 6 TROUBLESHOOTING 6 pin assignments and the signal timing of your computer with the specification outlined in 7. SPECIFICATIONS. ITEMS TO CHECK LOCATION PROBLEM • Contrast and brightness controls. • Front LED On (Green) • Power switch. • Front LED Off • Power cord disconnected. No • Rear picture • Signal cable disconnected. • Re
ページ16に含まれる内容の要旨
ENGLISH 7 SPECIFICATIONS 7 LCD Panel 46cm/18.1" Color TFT Panel Type Active Matrix Resolution 1280 dots x 1024 lines Pixel Pitch 0.28mm LCD MODULE Color Filter R, G, B vertical stripe type Face Finishing Anti-glare, Hard Coated Viewing Angle ±80°(Horizontal/Vertical) CR 5 Video 0.7Vp-p analog RGB Sync Sync.on Green or Separated H,V or Composite sync. INPUT SIGNAL Input Impedance Video 75 W Sync 2.2k W SCANNING Horizontal 24.0 - 80.0kHz FREQUENCY Vertical 50.0 - 86.0Hz DISPLAY SIZE H x V 3
ページ17に含まれる内容の要旨
LIMITED WARRANTY NEC-Mitsubishi (hereinafter “NEC-MITSUBISHI”), warrants This Product is warranted in accordance with the terms of this Product to be free from defects in material and work- this limited warranty. Consumers are cautioned that Prod- manship and, subject to the conditions set forth below, uct performance is affected by system configuration, soft- agrees to repair or replace (at NEC-MITSUBISHI’s sole ware, the application, customer data, and operator control option) any part of the
