ページ1に含まれる内容の要旨
INSTALLATION/OPERATION
PMC14H and PMC14H-GY
14-Inch Color Monitor
®
C2906M (7/03)
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this monitor near water. 6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Do not defeat the safety purpose of the polarized or grounding-type plug
ページ3に含まれる内容の要旨
DESCRIPTION The PMC14H is a high-resolution color monitor that can be used in desktop applications or rack mounted using the optional RMA14F rack mount kit. The monitor supports NTSC and PAL video, as well as 120 VAC and 230 VAC input power. An automatic switching system makes all the necessary changes for adapting to the required formats. Manual selection is not required. A separate power cord is supplied for each voltage input. The back panel of the PMC14H has two BNC video inputs with looping
ページ4に含まれる内容の要旨
INSTALLATION 1. Make all equipment connections as required for your Table A. Video Coaxial Cable Requirements installation. Refer to Figures 1 through 3 for samples of Cable Type* Maximum Distance installation methods. RG59/U 750 ft (229 m) Refer to Table A for coaxial cable requirements. RG6/U 1,000 ft (305 m) 2. Plug power cord into the AC INLET connection on the RG11/U 1,500 ft (457 m) rear panel of the monitor. Plug the other end into a power receptacle. *Minimum cable requirements: 75 ohms
ページ5に含まれる内容の要旨
VIDEO AUDIO V1 V2 V1 V2 S-VIDEO IN IN OUT CAMERA OUT S-VIDEO S-VHS OUT AUDIO OUT VCR Figure 2. S-VHS Video Input Connections Note: The S-Video connector is an input connector; there is no loop-through capability using S-Video. VIDEO AUDIO V1 V2 V1 V2 S-VIDEO IN IN CAMERA OUT OUT S-VIDEO VIDEO AUDIO V1 V2 V1 V2 S-VIDEO IN IN OUT OUT S-VIDEO VIDEO AUDIO V1 V2 V1 V2 S-VIDEO IN IN OUT OUT S-VIDEO VCR Figure 3. Looping Operation – Maximum of Three Monitors with External Video Equipment C2906M (7/0
ページ6に含まれる内容の要旨
OPERATION 1. Press the POWER button to turn the monitor on. The LED above the power button will illuminate when the monitor is on. 2. Select the camera by pressing the V1, V2, or S-VIDEO button (refer to Figure 4). 3. If required adjust the picture using the control knobs on the front panel. Refer to Figure 4 for front panel controls. FRONT PANEL ADJUSTMENTS TINT Color phase adjustment. Turn clockwise to increase the greenish tones in the picture. Turn counterclockwise to increase the reddish to
ページ7に含まれる内容の要旨
SPECIFICATIONS ELECTRICAL Input Voltage: 100-240 VAC, 50/60 Hz, automatic switching Power Consumption: 45 watts Horizontal Resolution: 450 TV lines, center of screen Visual Picture Size: 14-inch (35.56 cm) diagonal Sweep Linearity: 10% Speaker Output: 1.0 watt (-3 dBV) GENERAL Input/Output Video: 2 BNC inputs, 75 ohms or Hi-Z 2 looping outputs Audio: 3 RCA inputs, Hi-Z 3 looping outputs S-Video: 1 DIN input Construction: Steel cabinet Finish PMC14H: Black PMC14H-GY Gray Dimensions: 13.76 (W) x 1
ページ8に含まれる内容の要旨
WARRANTY AND RETURN INFORMATION WARRANTY If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to Pelco will repair or replace, without charge, any merchandise proved defective in material or obtain a Repair Authorization number (RA), and provide the following information: workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: 1. Model and serial number 2. Date of shipment, P.O. number, Sales
