Sanyo 42LM5RTCの取扱説明書

デバイスSanyo 42LM5RTCの取扱説明書

デバイス: Sanyo 42LM5RTC
カテゴリ: モニター
メーカー: Sanyo
サイズ: 0.49 MB
追加した日付: 9/30/2014
ページ数: 19
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスSanyo 42LM5RTCの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Sanyo 42LM5RTCに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Sanyo 42LM5RTCをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Sanyo 42LM5RTCのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Sanyo 42LM5RTCの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Sanyo 42LM5RTC 取扱説明書 - Online PDF
Advertisement
« Page 1 of 19 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Sanyo 42LM5RTCを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Sanyo 42LM5RTCの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨





Interactive Touchscreen
User Guide
For serial Interface







For use with models:
42LM4WPTC
42LM5WPTC
42LM4RTC
42LM5RTC


Version 1.3 September 2007
Interactive Touchscreen User Guide

ページ2に含まれる内容の要旨

2

ページ3に含まれる内容の要旨

TABLE OF CONTENTS ABOUT THIS MANUAL ........................................................................................................................ 4 CONTACT INFORMATION .................................................................................................................. 4 SHIPPING DAMAGE/UNPACKING ..................................................................................................... 4 CARE AND CLEANING OF THE TOUCHSCREEN .........................

ページ4に含まれる内容の要旨

ABOUT THIS MANUAL This manual is intended as a reference guide for the Interactive Touchscreen running under Windows XP™ or Windows Vista™. This User Manual provides the information needed to set up the touchscreen. In addition, this manual describes basic technical information about the touchscreen and troubleshooting. CONTACT INFORMATION If you have any questions or issues, please contact your original equipment supplier SHIPPING DAMAGE/UNPACKING Every precaution is ta

ページ5に含まれる内容の要旨

INTRODUCTION This manual will explain the workings and setup of the touchscreen fitted to your display. An explanation of the monitor and its workings is covered in the Monitor Manual that came with this product. The following pages will tell you how to install the software needed by the touchscreen to function and go through the adjustments that user’s can change to enable the screen to perform effectively in many different environments. The Ma7 Driver software has been written t

ページ6に含まれる内容の要旨

INSTALLATION LOADING THE TOUCH DRIVER SOFTWARE ONTO PC 1. Switch on monitor Do not plug the touchscreen interface cable into your computer. 2. Insert the ‘Information & Touch Software installation CD’ into the PC and follow the automatic installation instructions. If the installation does not start automatically; 1. Click START on the Windows™ Taskbar; then click RUN. 2. Type d:\Autorun.exe where d is the letter of your CD-ROM drive. Click OK 3. Select the ‘Touch softwa

ページ7に含まれる内容の要旨

STARTING THE DRIVER CONTROL PROGRAM Connect the touchscreen cable to a free serial port of the. 1. If the Touchscreen control panel is not already running, start the driver by clicking the icon on the desktop or select the Windows™ START button and RUN "Ma7_Control_En.exe" with the necessary path or double click Ma7_Control_En.exe from ‘Windows Explorer™’ or click the short cut placed on the desktop. When the program is started it displays the following window (Fig 1): Fig 1

ページ8に含まれる内容の要旨

Fig 2 EXPLANATION OF THE STATUS SECTION 1. The following explanation of the Status section assumes that the touchscreen is physically attached to a serial port of the PC: Open - will go red and remain red only when the driver is present, the correct port is chosen and the Baud rate is set correctly. If the Open box does not go red then the driver is not loaded or another driver has taken the port. If the Open box goes on and off repeatedly then the driver is loaded but ano

ページ9に含まれる内容の要旨

The mouse pointer will not respond to a touch until it has been enabled in the Output section of the Control Program. Details of this will follow later in this manual. The Reset button loads fresh data from the touchscreen. This is used as a reference for detecting any new touches. This may be necessary if the touchscreen environment has been changed; for example, the touchscreen has been moved. 9

ページ10に含まれる内容の要旨

ADJUSTING THE TOUCH SENSITIVITY LEVEL Automatic Setup When you receive your unit, the sensitivity settings will have been optimised when the unit was manufactured. These settings should only be altered if you are experiencing problems such as an electrically noisy environment. Contact your supplier if you need further explanation. 1. To select the sensitivity setup click on the Sense tab. Fig 3 2. First set the Course Sensitivity to approximately two thirds by dragging the bar

ページ11に含まれる内容の要旨

7. The moving indicator under Finger Pressure shows the strength of touchscreens signal. Nominally the Coarse Sensitivity slider is adjusted so the Finger Pressure indicator moves about a third of the way along in response to a light touch. 8. The Press Threshold slider is used to adjust the sensitivity of the touch to simulate a mouse button press. The driver recognises a touch when the Finger Pressure indicator exceeds the position of the Press Threshold slider. As default this is the

ページ12に含まれる内容の要旨

CALIBRATION 1. Select the Calib tab as shown below (Fig 5), click the 'Start Calibration' box. Fig 5 2. You will see the following screen (Fig 6); there are three targets to touch in total, like the one shown below: Fig 6 3. When each of these targets is displayed, touch and hold your finger on the centre of the circular target. You must touch all three targets in turn. 4. The red circle in the target slowly moves towards the centre of the target. 5. Remove your finger

ページ13に含まれる内容の要旨

SETTING THE TOUCH OUTPUT TO SUIT THE APPLICATION PROGRAM 1. Select the Output tab. Fig 7 2. Select the mouse control required for your application (Fig 7). To enable the touch function on the screen, tick the Enable check box. 3. No action selects no mouse pointer movement or button pressing when touching the touchscreen. 4. Move mouse only enables mouse pointer movement but no button movement when touching the screen. 5. Click on press enables mouse pointer moveme

ページ14に含まれる内容の要旨

You must now save the settings Fig 8 1. (Fig 8) Click on file. 2. Click on save to save the current settings. When the touchscreen driver has been set up and there is no requirement to change it. 14

ページ15に含まれる内容の要旨

DIAGNOSTICS AND FREQUENTLY ASKED QUESTIONS Testing the Hardware with ‘Graph’ 1. Select the Graph tab. Fig 9 2. Run a finger around the sensor, the effect of the finger on nearby wires can be seen by a visible movement on the indicators (Fig 9), each representing one wire. The algorithm in the driver interpolates the response curve to generate an accurate co-ordinate for the finger position. The following hardware checks can now be made: Wire Integrity Test 3. Run a fi

ページ16に含まれる内容の要旨

MONITOR MODE Fig 10 1. This section is used to check the output of the touchscreen over the whole display area represented by the white box in the centre. It is useful in checking for any dead areas on the touchscreen and the performance of the touchscreen being able to follow the finger accurately and responsibly (Fig 10). 2. When using this feature make sure that the touchscreen output is disabled by un-ticking the Enable Selection Control in the output section. When the finge

ページ17に含まれる内容の要旨

USING EDGE ENHANCEMENT 1. To allow easy access to the sliders and buttons at the edge of the display, the cursor can be positioned nearer the edge of the screen. The amount of enhancement can be adjusted via the screen shown. Fig 13 2. Each of the sliders represents one edge of the sensor; the default position is as illustrated above (Fig 13). 3. Edge Gain can also be used to counteract the effects of nearby metalwork that surrounds the display area. 4. The further the s

ページ18に含まれる内容の要旨

FAULT FINDING GUIDE The following are some possible reasons why the touch screen might not work. If they do not solve your problem or you have a situation not covered please contact your supplier. DRIVER DOES NOT SEE THE TOUCHSCREEN Touchscreen on a different comm port than the one selected. The Baud rate is incorrect. Another device, driver or program is using the port. TOUCHSCREEN PERFORMS BADLY NEAR THE EDGES OF THE DISPLAY Metal framework near to the touchscreen may inter

ページ19に含まれる内容の要旨

There are several ways to improve system performance. Optimise the Background performance against the Applications, to do this follow the simple instructions below: Select the Windows™ START Button; go into Settings and Control Panel. Open the System folder and select the Advance tab. Press the Performance Options button. Change the selection from Optimise Performance for Applications to Optimise Performance for Background Services. CHECK OR CHANGE THE VIRTUAL MEMORY SETT


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Sanyo CE32LM4WPR-E 取扱説明書 モニター 17
2 Sanyo 42LM4RTC 取扱説明書 モニター 11
3 Sanyo CE42SR1 取扱説明書 モニター 1
4 Sanyo CE42WPX1 取扱説明書 モニター 1
5 Sanyo VMC-8619PA 取扱説明書 モニター 0
6 Sanyo ECD-T1580DV 取扱説明書 モニター 5
7 Sanyo VMC-L1015 取扱説明書 モニター 1
8 Sanyo VMC-8620 取扱説明書 モニター 0
9 Sanyo PDP-32H1AN 取扱説明書 モニター 2
10 Sanyo 42LM5R 取扱説明書 モニター 4
11 Sanyo VMC-L1019 取扱説明書 モニター 0
12 Sanyo 42SR1 取扱説明書 モニター 5
13 Sanyo CE42LM5R 取扱説明書 モニター 1
14 Sanyo CE42LM5WPR 取扱説明書 モニター 0
15 Sanyo VM-6609 取扱説明書 モニター 0
16 Sony BVM-L170 取扱説明書 モニター 7
17 Sony DDM-2802CNU 取扱説明書 モニター 1
18 Sony BVM-D20F1U, BVM-D20F1E, BVM-D20F1A, BVM-D24E1WU, BVM-D24E1WE, BVM-D24E1WA, BVM-D32E1WU, BVM-D32E1WE, BVM-D32E1WA 取扱説明書 モニター 15
19 Sony 500A3WE 取扱説明書 モニター 8
20 Sony CPD-17SF2 取扱説明書 モニター 10