ページ1に含まれる内容の要旨
17 ” TFT-LCD TV MONITOR
V171HT
USER ’ S MANUAL
Rev. 1.0
www.viewera.com
ページ2に含まれる内容の要旨
CONTENTS 1. Introduction Product Description Congratulations on your purchasing ViewEra LCD TV monitor. It 1. Introduction incorporates high quality display into a small light weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit Product Description .................................. Page 1 from this monitor in lots of ways; to name some of them: comfort safety, and Package Contents ..................................... Page 1 en
ページ3に含まれる内容の要旨
Product Features Additional High contrast ratio TFT LCD display supports resolution up to SXGA Read all of these instructions and save them for later use. 1280 × 1024. @75Hz. Follow all warnings and instructions on the product. Wall mountable with. Product Built-in speakers provide sound performance. ♦ Do not cover or block the venting holes in the case. Power management system conforms to VESA DPMS standard. ♦ Do not insert sharp objects or spill liquid into the LCD mo
ページ4に含まれる内容の要旨
2. Control Functions Power and extension cords a. 【PC,Audio,DVI 】 ♦ Do not allow anything to rest on the power cord. Control Button Front View ♦ Do not locate this product where persons will walk on the cord. ♦ Use the proper power cord with correct attachment plug type. If the power source is 120V AC, use a power cord that has UL and C-UL ﹝2 ﹞ ﹝5 ﹞ ﹝1 ﹞ ﹝3 ﹞ ﹝4 ﹞ approvals. If the power source is a 240V AC supply, use the tandem (T blade) type attachment plug with ground condu
ページ5に含まれる内容の要旨
OSD Controls Tools Menu : Monitor Function Selection Menu : VOLUME Adjust the speaker volume by using + and - AUTO ADJUST Select this function to obtain the best display quality buttons. and adjust the image position . MUTE Speakers are mute. BRIGHTNESS Adjust the brightness by using + and - buttons. CONTRAST Adjust the contrast by using + and - buttons. RESET Recall the factory settings CLOCK Adjust the clock by using + and - button
ページ6に含まれる内容の要旨
Color Temperature and RGB Adjusting Menu : COLOR Color temperature selection --6500K, 7500K and OSD Function Selection Menu : TEMP. 9300K. EXIT OSD Exit the OSD menu. RED Red pixel brightness adjustment. OSD H. Press + to move the OSD to right ; POSITION Press - to move the OSD menu to left. Green pixel brightness adjustment. GREEN OSD V. Press + to move the OSD menu upward ; POSITION Press - to move the OSD menu downward. BLUE Blu
ページ7に含まれる内容の要旨
b. 【AV,TV 】 Control Button Front View ﹝5 ﹞ ﹝4 ﹞ ﹝1 ﹞ ﹝2 ﹞ ﹝3 ﹞ 1. Power Switch Power switch and remote sensor Monitor Function Selection Menu : 2. Decrease ( -) Volume decrease, OSD menu selection downward and BRIGHTNESS Adjust the brightness by using + and - buttons. channel down ( -) in TV mode. 3. Increase ( +) Volume increase, OSD menu selection upward and CONTRAST Adjust the contrast by using + and - buttons.
ページ8に含まれる内容の要旨
** TV Mode only ** TV Function Selection Menu : CH SEARCHING TV channel auto searching Tools Menu : CH EDIT Add or delete channel. VOLUME Adjust the volume by using + and - buttons. CH FINE TUNE Tune up the signal for channel reception. MUTE Speakers are mute. AIR-CABLE Select TV signal ,air or cable, by using + RESET Reset function. and - buttons. CH SYSTEM TV system selection. INPUT Select input signal (PC →AV →S-Vid
ページ9に含まれる内容の要旨
3. Input Diagrams 4. Installation Inputs Electrical Connection Please follow the instruction below to properly connect the LCD monitor to external electrical source. 1. Connect the female-end of the power cable to the transformer. Connect the male-end of the power cable to the wall outlet or extension cable. 2. Connect the cable from the other end of the transformer to the LCD monitor DC IN located at the back of the LCD monitor. 【1 】 【2 】 【3 】 【4 】 【5 】 【6 】 【7 】 Signal Connec
ページ10に含まれる内容の要旨
Display Modes 5. Product Specifications Mode Resolution H Freq (KHz) V Freq (Hz) Model 1 640 × 350 31.469 70.070 V171HT Spec 2 640 × 480 31.469 59.940 LCD Display 17” Active matrix TFT LCD panel 3 640 × 480 37.861 72.809 Pixel Pitch 0.264(H) x 0.264(V) mm 4 640 × 480 37.500 75.000 Max. Resolution 1280(H) x 1024(V), SXGA 5 720 × 400 31.469 70.087 Contrast Ratio Typical: 500 : 1 (Min: 400:1) 6 800 × 600 35.156 56.250 Brightness Typical : 300 cd/m2 (Min : 250) 7 800 × 600 37.879 6
ページ11に含まれる内容の要旨
8. Windows setup 6. Dead Pixel Policy For the best display quality, please set the monitor type in Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra Windows. guarantees that the monitor will be replaced if the number of dead pixels on our monitor exceeds 5 pixels within the first year from the date of purchase. Control Panel > Display > Settings > Advanced > List All Modes 7. Warranty and Customer Service For optimal resolution, please select “ 1280 × 10
ページ12に含まれる内容の要旨
9. Remote Control Function 10. Trouble Shooting 1) Power on but no picture → Make sure the VGA cable is tightly connected from the video output connector on the video card to the video input connector on the monitor. 1 → Make sure you are using the standard power adapter coming with the 8 monitor. 7 10 → Check your video card if the driver is correctly installed. If there is no 9 video signal from the video card, “ NO INPUT SIGNAL” will show on the 5 screen. 4 6 3 2) Wrong
ページ13に含まれる内容の要旨
6) Residue image The “ Out of Range” may happen if you switch monitor A to monitor B for → If an image remains on the screen for an extended period of time, it may your PC. Whenever you change the monitor for your PC, your PC may be imprinted in the screen and leave a residue image. It is characteristic of liquid crystal and is not malfunction or deterioration of the liquid crystal. detect it as a new hardware and automatically install a proper driver for the The residue image will di