ページ1に含まれる内容の要旨
Model 29578
Desktop Speakerphone
with Amplified Volume
and Tone Control
User’s Guide
ページ2に含まれる内容の要旨
Important Information NOTICE: This product meets the applicable Industry Canada technical specifications. Operation is subject to the following two conditions: (1) This device may not cause interference, and () This device must accept any interference, including interference that may cause undesired operation of the device. The equipment must be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degrad
ページ3に含まれる内容の要旨
Interference Information This equipment generates and uses radio frequency energy which may interfere with residential radio and television reception if not properly installed and used in accordance with instructions contained in this manual. Reasonable protection against such interference is ensured, although there is no guarantee this will not occur in a given installation. If interference is suspected and verified by switching this equipment on and off, the user is encouraged to try to
ページ4に含まれる内容の要旨
Notice must be given to the telephone company upon termination of your telephone from your line. REN Number On the bottom of this equipment is a label indicating, among other information, the Ringer Equivalence Number (REN) for the equipment. The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to
ページ5に含まれる内容の要旨
Table of Contents i MPor TanT .i nforMa Tion ......... 2 Answering A CAll ........16 i nTerference .i M nfor a Tion ..... 3 HAndset .........................16 TelePhone .n e TWork . s pe AH kerp one ................17 i M nfor a Tion .................... 3 Vumeol ................................17 ren.n M u ber ....................... 4 Amplified Audio .................17 h earing .a id .c MP o a TT ibili y . t one e qu Alizer ..................19 (cha )............................ 4 n eCoopkl
ページ6に含まれる内容の要旨
Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. This phone is designed for those individuals with mild to severe hearing loss. The unit is designed to control the volume of the phone as well as the frequencies that best fit your hearing. It has three pitch control buttons allowing you to customize the phone t
ページ7に含まれる内容の要旨
Before You Begin Parts Checklist Make sure your package includes the items shown here. Telephone Base Handset line cord Vibrating Handset Power Alert cord Supply Telephone Jack Requirements Wall plate To use this phone, you need an RJ11C type modular telephone jack, which might look Modular like the one pictured here, installed in your telephone home. If you don’t have a modular jack, line jack call your local phone company to find out how to get one installed.
ページ8に含まれる内容の要旨
Installation Important Installation Guidelines • Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave ovens, heating appliances and direct sunlight. • Avoid areas of excessive dust, moisture and low temperature. • Avoid other cordless telephones or personal computers. • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch non-insulated
ページ9に含まれる内容の要旨
Base Layout ALARM AMPLIFY HOSPITAL button button button M2/M4 M1/M3 FIRE (memory (memory button buttons) buttons) REDIAL button STORE button FLASH button TONE EQUALIZER VOLUME (p/q) buttons MUTE button # PAUSE SPEAKER * button button button
ページ10に含まれる内容の要旨
Back & Side Views LINE jack DATA jack AMPLIFY Override (BACK VIEW) Switch RINGER PITCH (HIGH/LOW) VIBRATING RINGER VOL ALERT switch (HIGH/LOW/OFF) switch NECKLOOP (SIDE VIEW) 10
ページ11に含まれる内容の要旨
Installing the Phone Installing Backup Batteries CAUTION: Disconnect the phone cord from the wall outlet before installing or replacing the batteries. In case of a power outage, the phone uses 4 AA alkaline batteries for backup power for incoming voice amplification and visual ringer functions. 1. Unplug the power adaptor and the telephone line before installing batteries. 2. Carefully turn over the phone, and release latch on battery compartment and remove cover. 3. Insert 4 AA-si
ページ12に含まれる内容の要旨
NOTE: Remove the batteries if storing the unit for over 30 days to prevent damage in the event of leaking batteries. Connecting the Telephone Line NOTE: The unit is shipped from the factory for placement on a level surface. 1. Choose an area near a telephone wall jack (RJ11C), and place your cordless telephone on a level surface, such as a desktop or tabletop, or you may mount it on the wall. 2. Plug one end of the telephone line cord into the Line jack at the back of the base and th
ページ13に含まれる内容の要旨
CAUTION: To reduce risk of personal injury, fire, or damage use only the 5-2784 power adaptor listed in the user’s guide. This power adaptor is intended to be correctly orientated in a vertical or floor mount position. 5. You can stretch out the kick-stands on the bottom of the base for a better viewing angle when placed on desktop. 6. Connect one end of the coiled handset cord to the jack on the handset. 7. Plug the other end of the coiled handset cord to the jack on the base. 8. Make s
ページ14に含まれる内容の要旨
Wall Mounting 1. Plug the AC power adaptor into the electrical outlet and the DC connector into the jack on the back of the base. 2. Plug one end of the straight telephone line cord into the jack on the bottom of the base. 3. Close the kick-stands on the bottom of the base unit if you’ve opened them before. 4. Feed the line cord through the groove and plug the end into the modular telephone jack. Excess telephone line can be stuffed into the recess area on the bottom of the Base U
ページ15に含まれる内容の要旨
Telephone Operation Speakerphone For hands-free operation and convenience, this unit is equipped with a speakerphone. For best speakerphone performance, avoid the following: • Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.) • Surfaces affected by vibration. • Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect. Note
ページ16に含まれる内容の要旨
Placing a Call Handset 1. Pick up the handset and listen for a dial tone. 2. Dial the number you want to call. 3. When finished, hang up the handset. Speakerphone 1. Press the speaker button on the base and listen for a dial tone. 2. Dial the number you want to call. 3. When finished, press the speaker button to hang up. Answering a Call NOTE: Make sure the ringer switch is set to HI or LO, or the phone will not ring. The visual ring indicator will flash at all settings. Handset 1. When t
ページ17に含まれる内容の要旨
Speakerphone 1. When the phone rings, press the speaker button to answer a call. 2. When finished, press the speaker button to hang up. You may switch between the speakerphone and the handset during the dialing process or anytime during a conversation. Speakerphone to Handset - Pick up the handset to disable the speakerphone. The speakerphone indicator turns off. Handset to Speakerphone - Press the speaker button, and then hang up the handset. The speakerphone indicator turns on and the
ページ18に含まれる内容の要旨
The “AMPLIFY” button controls the increased volume level and tone equalizer of the handset. 1. Press the volume (p or q) button to minimum, pick up the handset and press the amplify button to turn on the incoming voice amplifier . The indicator around the button illuminates. 2. Adjust the volume by pressing the volume (p or q) button. When the amplify button is pressed , an extra level of amplified volume is added providing up to 40dB of gain and level control. In standard use, the ampl
ページ19に含まれる内容の要旨
Tone Equalizer The phone’s 3-band tone equalizer boosts the sound of the three frequency ranges ( 600Hz, 1.2KHz, 2.4KHz ) to compensate for the ear’s limited sensitivity in these ranges. 1. To turn on the equalizer, press the “amplify” button after you pick up the handset, or any time during the a call. The indicator around the button illuminates. 2. To adjust the setting open the equalizer cover. Slide each switch toward “+” to increase or amplify sounds, or toward “-” to decrease the
ページ20に含まれる内容の要旨
Mute Use the mute button to interrupt a phone conversation to talk privately with someone else in the room . A conversation can be muted while using the speakerphone, handset or neckloop. 1. Press the mute button. The mute indicator illuminates. 2. Press mute again to turn it off. Note: Switching from speakerphone to handset cancels mute. Vibrating Alert The unit is equipped with a 2.5mm vibrating alert jack for an optional vibrating pad to alert you when the phone is ringing. Simply plu
