ページ1に含まれる内容の要旨
'6/3977"5/.KPG"2JQPG
YKVJ"5RGCMGTRJQPG
43-1755 OWNER’S MANUAL — Please read before using this equipment.
%106'065
Read This Before Installation ..... 2
The FCC Wants You to Know .... 2
FCC Statement .......................... 3
Lightning ................................. 3
Selecting a Location ................... 3
On a Desk ............................... 4
On a Wall-Plate ....................... 4
On a Wall ................................ 5
Connecting to Another Phone .... 6
Connecting the Ha
ページ2に含まれる内容の要旨
Auto-Line Selection — automatically selects a line so you "+/2146#06" # # do not need to press a line button. If an icon appears at the end of a paragraph, go to the box on that Auto-Ringer Selection — automatically selects the line page with the corresponding icon which is ringing, or LINE 1 when three lines are ringing for pertinent information. simultaneously. — Warning — Important # Rý Hearing Aid Compatible — lets you use this telephone . — Caution ± — Note with hearing aids that h
ページ3に含まれる内容の要旨
(%%"56#6'/'06 Your telephone complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number ±"016'"±" and the REN to your telephone company. Both numbers are You must not connect your phone on the bottom of the telephone. ± to: • coin-operated systems .+)*60+0) • party-line systems Your telephone has built-in protection circuits to reduce the • most electronic key telephone risk of damage from surges in telephone line and power line current. These protecti
ページ4に含まれる内容の要旨
10"#"&'5- 1. Insert the mounting bracket’s four tabs into the slots on the bottom of the base then slide up to snap the mounting bracket into place. 2. If you have a two-line phone jack and a one-line phone jack, plug one end of the supplied two-line long modular cord into LINE L1/ L2 on the bottom of the base, and plug one end of the supplied single-line long modular cord into L3. Then route both line cords through the left and middle slots on the mounting bracket. If you have three
ページ5に含まれる内容の要旨
If the wall plate has a single one-line phone jack, and there is a two-line phone jack nearby, plug one end of the supplied one-line short modular cord into L3, and plug the two-line long modular cord into LINE L1/L2. Then plug the one-line short modular cord’s other end into the wall plate jack, and plug the two-line long modular cord's other end into the two-line wall jack. 4. Align the wall plate studs with the phone’s keyhole slots and slide the phone downward to secure it. Then pl
ページ6に含まれる内容の要旨
%100'%6+0)"61"#016*'4" 2*10'" The phone is equipped with a DATA jack so you can connect another phone or an answering machine to LINE2. You can plug one end of a modular cord into either LINE L1/L2 or L3, or DATA at the right side of the phone, then plug the other end into the jack of another phone or an answering machine. You cannot use LINE 2 while another phone or answering machine is connected to DATA and in use. LINE 1 and LINE 3 still function normally. When you are finished using
ページ7に含まれる内容の要旨
5'66+0)"6*'"&+#.+0)"/1&' ±"016'"±" Set TONE/PULSE on the bottom of the phone for the type of • If your phone system requires service you have. If you are not sure which type you have, that you dial an access code (9, do this simple test. for example) before you dial an outside number, do not press 1. Set TONE/PULSE on the bottom of base to TONE. that number. • If the dial tone stops, you have 2. Lift the handset, or press SPEAKER/HEADSET to listen touch-tone service. Leave for a dial to
ページ8に含まれる内容の要旨
59+6%*+0)"$'69''0"6*'"*#0&5'6"#0&" ±"016'"±" 6*'"52'#-'42*10' • If background noise interferes To switch from the handset to the speakerphone at any time with the speakerphone’s during a call, press SPEAKER/HEADSET so the SPEAKER operation, press MUTE to turn indicator lights. ± off the base’s microphone while the other party is speaking (see To switch from the speakerphone to the handset, just lift the “Using MUTE” on Page 8). handset. The SPEAKER indicator turns off. • You cannot use t
ページ9に含まれる内容の要旨
75+0)"*1.& ±"016'"±" To put a call on hold, press HOLD. The line indicator flashes. • You can put a call on hold at You can then hang up the handset or use the other phone one extension and pick up the line (or answer another call, for example) without call at another extension. disconnecting the current call. • You can alternate between two lines by pressing HOLD to put To resume the call, press that line’s button (LINE 1, LINE 2 or your current line on hold, then LINE 3) if the handse
ページ10に含まれる内容の要旨
For an upper memory location, press a memory number button. For a lower memory location, press LOWER, then a memory number button. After completion, the LOWER indicator flashes. To store additional numbers, repeat steps 1–3. '06'4+0)"#"2#75'"+0"#"/'/14;"07/$'4 In some telephone systems, you must dial an access code (9, for example) and wait for a second dial tone before you can dial an outside number. You can store the access code with the phone number. However, you should also store a ±"0
ページ11に含まれる内容の要旨
2. Write the name or number next to the appropriate memory location on the provided card. The card has an upper and lower position for each memory location. 3. Insert the plastic cover’s tabs into the slots on the base, align the memory buttons with the cover and carefully press down on the cover to secure it. 75+0)"#0"126+10#."*'#&5'6 ±"016'"±" Your phone is equipped with a headset jack on the base, so • Connecting a headset you can connect an optional headset. ± disconnects the handset’s
ページ12に含まれる内容の要旨
If you still have problems, disconnect the phone. If other phones on the same line(s) work properly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to your local RadioShack store for assistance. %#4' Keep the phone dry; if it gets wet, wipe it dry immediately. Use and store the phone only in normal temperature environments. Handle the phone carefully; do not drop it. Keep the phone away from dust and dirt, and wipe it with a damp cloth occa
