Summary of the content on the page No. 1
User’s manual
AT3101
Expansion DECT 6.0
cordless handset
For use with the AT&T AT3111-2
telephone system with
caller ID/call waiting
Summary of the content on the page No. 2
Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read the Important safety instructions on pages 18-21 of this manual. Please thoroughly read the user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. For complete instructions, please refer to the manual provided with your AT3111-2 telephone Model #: AT3101 Type: Expansion DECT 6.0 digital cordless handset Serial #: Purch
Summary of the content on the page No. 3
You must install and See page 3 charge the battery before for easy instructions. STOP! using the telephone. CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read and follow these instructions carefully: • Use only the supplied rechargeable battery or replacement battery (model: BT8001) or equivalent. • Do not dispose of the battery in a fire. Like other batteries of this type, it could explode if burned. Check with local codes for special disposal instru
Summary of the content on the page No. 4
Getting started Parts checklist Your new AT&T AT3101 expansion handset includes: Cordless telephone Handset battery Belt clip Battery handset compartment cover User’s manual AT3101 Expansion DECT 6.0 cordless handset For use with the AT&T AT3111-2 telephone system with caller ID/call waiting Charger for cordless handset User's manual Power adapter for handset charger Table of contents Getting started Appendix Parts checklist .......................1 Troubleshooting ....................
Summary of the content on the page No. 5
Getting started Charger installation Install the charger as shown below. Make sure that the electrical outlet is not controlled by a wall switch. 1. Plug the small end 2. Plug the of the smaller power large end of adapter into the jack the smaller on the underside of the power adapter charger, then route the into an cord through the slot as electrical outlet. shown. NOTES: 1. Use only the power adapter supplied with this product or equivalent. 2. This power unit is intended to be co
Summary of the content on the page No. 6
HB9wwwwW ,wwwwwwww EBB
HC9
WWww w , w w w w , w w HB9wwwwW ,wwwwwwww EBB
HC9
WWww w , w w w w , w w HB9wwwwW ,wwwwwwww EBB
HC9
WWww w , w w w w , w w Getting started Battery installation & charging The battery may have enough charge for short calls. For optimal performance, we recommend that you charge the handset for 16 hours. You can keep the battery charged by returning the handset to the telephone base after each use. When the battery power is fully depleted, a full recharge takes about
Summary of the content on the page No. 7
Getting started Adding your new handset Handsets purchased separately need to be registered to the telephone base before use. When first purchased, all NOT REGISTERED optional accessory handsets will show NOT REGISTERED on the screen. The new handset may need to be charged for five minutes before registering to the main telephone base. To register a handset to your telephone base 1. Place the unregistered handset into the PRESS FIND HNDST telephone base. If PRESS HNDST LOC 4 4 SEC ON B
Summary of the content on the page No. 8
Getting started Replacing a handset When you are replacing rather than adding a handset, for your handsets to be numbered sequentially, you need to delete all the handset registrations on the telephone base. To de-register all handsets 1. Press and hold FIND HANDSET on the telephone base for about 10 seconds (until the IN USE light turns on and starts to flash), then release the FIND HANDSET button. 2. Immediately press and release FIND HANDSET again. You must press FIND HANDSET while the
Summary of the content on the page No. 9
Getting started Handset layout 1. Earpiece 2. MENU/SELECT SKIP 3. Headset jack (2.5mm) 4. CID (caller ID) HANDSET 1 PLAY 5. /FLASH 6. Dialing keys (0-9, *, #) 7. VOICEMAIL 8. REDIAL/PAUSE 9. Microphone 10. Handset display 11. VOL / (volume) 12. (directory) 17 ERASE 13. (speakerphone) 14. OFF/CLEAR 15. # 16. INT (intercom) 17. MUTE/REMOVE 6
Summary of the content on the page No. 10
IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx IC:xxxxX-xxxxxxxx FCC ID: XXxxx-xxxx-xx Getting started Belt clip & optional headset Install belt clip as shown below if desired: Removal Installation Pull and unlock Snap belt clip one flap from the into notches notch first before on both sides detaching the of handset. whole belt clip from handset. For hands-free telephone conversations, use any industry standard 2.
Summary of the content on the page No. 11
Appendix Troubleshooting If you have difficulty with your telephone, please try the suggestions below. My phone • Make sure the power cord is securely doesn’t work plugged in. at all • Make sure that the battery connector is securely plugged into the cordless handset. • Make sure the telephone line cord is securely and firmly plugged into the telephone base and the telephone wall jack. • Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance
Summary of the content on the page No. 12
Appendix Troubleshooting • If the previous suggestions don’t work, disconnect the telephone base from the telephone jack and connect to a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your local telephone company. • Your line cord might be malfunctioning. Try installing a new line cord. I cannot dial • First try all the suggestions above. out • Make sure you have a dial tone before dialing. The cordless hands
Summary of the content on the page No. 13
Appendix Troubleshooting My cordless • Make sure the power cord is securely handset isn’t plugged into the telephone base. Plug the performing unit into a different, working electrical outlet normally not controlled by a wall switch. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the unit’s electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and tele
Summary of the content on the page No. 14
Appendix Troubleshooting • Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from these types of electronic devices as possible: television sets, VCRs, or other cordless telephones. The batteries • If the cordless handset is in its telephone will not hold a base or charger and the charge light does charge not come on, refer to The charge light is off in this Troubleshooting guide. • Char ge the battery in the cordless han
Summary of the content on the page No. 15
Appendix Troubleshooting • You may be able to improve the performance of your cordless phone by installing your new telephone base as far as possible from any other existing cordless telephone system that may already be installed. • Other electronic products can cause interference to your cordless phone. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones. • Do not install this phone near a m
Summary of the content on the page No. 16
Appendix Troubleshooting • Disconnect the telephone base from the I hear other telephone jack, and plug in a different calls while using telephone. If you still hear other calls, the my phone problem is probably in your wiring or local service. Call your local telephone company. • Make sure that the ringer is not turned off. My cordless Refer to the section(s) on ringer selection in handset does this user’s manual. not ring when I receive a call • Mak e sure the telephone line cord
Summary of the content on the page No. 17
Appendix Troubleshooting • Test a working phone at the phone jack. If another phone has the same problem, the problem is the phone jack. Contact your local telephone company (charges may apply). • Other electronic products can cause interference with your cordless phone. Try installing your phone as far away as possible from electronic devices like television sets, VCRs, or other cordless telephones. • Re-install the battery, and place cordless handset in the telephone base. Wait for
Summary of the content on the page No. 18
Appendix Troubleshooting • Relocate your telephone base to a higher location. The phone will have better reception when not installed in a low area. • If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your local telephone company (charges may apply). The charge • Make sure the power and line cords are light is off plugged in correctly and securely. • Unplug the unit’s electrical power. Wait for 15 seconds, then plug it b
Summary of the content on the page No. 19
Appendix Troubleshooting System does • Make sure you subscribe to caller ID with call not receive waiting features services provided by your caller ID when local telephone company. Caller ID features on a call will work only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment. If the unit does not seem to be responding Common cure normally, try putting the cordless handset in for electronic its base. If it does n
Summary of the content on the page No. 20
Appendix Troubleshooting • If the system’s memory becomes full during a message, the system stops recording and disconnects the call. • If the caller's voice is very soft, the system may stop recording and disconnects the call. System does • Make sure you subscribe to caller ID with call not receive waiting features services provided by your caller ID when local telephone company. Caller ID features on a call will work only if both you and the caller are in areas offering caller ID servi
