Summary of the content on the page No. 1
26976
900MHz SPACEMAKER® Under the
Counter Call Waiting Caller ID Cordless
Speakerphone/Answering System with
Digital AM/FM Radio and Timer
User’s Guide
We bring good things to life.
Summary of the content on the page No. 2
EQUIPMENT APPROVAL INFORMATION Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA. 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provi
Summary of the content on the page No. 3
INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection again
Summary of the content on the page No. 4
TABLE OF CONTENTS LANGUAGE ..................................... 16 EQUIPMENT APPROVAL INFORMATION ......... 2 LOCAL AREA CODE .......................... 17 INTERFERENCE INFORMATION .................... 3 TONE/PULSE DIALING ...................... 17 HEARING AID COMPATIBILITY.................... 3 DISPLAY CONTRAST ......................... 18 INTRODUCTION ...................................... 6 ANSWERING SYSTEM ON/OFF ......... 18 DIGITAL SECURITY SYSTEM ................. 7 SETTING THE RINGS TO
Summary of the content on the page No. 5
CALL TIMER .................................... 25 RADIO OPERATION ............................... 34 SPEAKERPHONE OPERATION ................... 26 AM ANTENNA ................................ 34 SPEAKERPHONE LOCATION................. 26 FM ANTENNA ................................ 35 SPEAKERPHONE GUIDELINES .............. 26 TURNING ON THE RADIO ................... 35 REGISTRATION ................................. 26 BAND ............................................ 35 RECEIVING A CALL ..........
Summary of the content on the page No. 6
INTRODUCTION CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. Your Caller ID phone stores and displays specific information, provided by your local telephone company, to subscribers of Caller ID or similar caller identification services. Your Caller ID phone enables you to: • Identify callers before you answer the phone. •View the t
Summary of the content on the page No. 7
Summary of the content on the page No. 8
INSTALLATION GUIDELINES • Install the wall base unit near both a telephone (modular) jack and an electrical power outlet. • The Spacemaker® unit is a cordless speakerphone with radio and answering machine. Before mounting it under a cabinet, check if the cordless speakerphone and the radio work well at the selected location first, also check the orientation of the power converter cord for the best FM radio reception. •Avoid sources of noise, such as a window by a busy street, and electrical nois
Summary of the content on the page No. 9
page CONNECTING THE TELEPHONE LINE 1. Connect one end of the telephone line cord to the LINE jack on the bottom of the wall base unit. 2. Connect the other end of the telephone line cord to a telephone jack on the wall. 3. Raise the antenna on the base. Insert another phone CONNECTING THE AC (ELECTRICAL) POWER 1. Plug the wall base unit into an electrical outlet. 2. Make sure that its pins are inserted fully into the outlet and it is firmly installed. If not, choose another electrical outlet to
Summary of the content on the page No. 10
a n n C m c h A a r c g o L e K L L i SPACEMAKER® UNIT TIP: Before mounting the Spacemaker® unit under the counter, it is highly recommended to check if the speakerphone and radio work well at the mounting location first. CONNECTING THE AC (ELECTRICAL) POWER Plug the AC power converter into an electrical outlet and the DC connector into the back of the Spacemaker ® Unit. CAUTION: Use only the ATLINKS USA, Inc. 5-2631 power converter that came with this unit. Using other power converters may dama
Summary of the content on the page No. 11
MOUNTING HARDWARE PACKED WITH YOUR UNIT 4 –1/4” Spacers 4 – Washers 4 –1/2” Spacers 4 – Cord hooks 4 – 1” Spacers 4 – 2” Phillips head screws CUTOUTONSOLIDBLACKLINE. CORTESOBRELALÕNEAS”LIDANEGRA. SEE INSTRUCTION BOOK: Be sure to select the correct height provided spacers to position this unit at the proper distance provide access to the handset. Handset will be below the front edge of your cabinet. This will slightly below the bottom of your cabinet when properly installed. Sinohayunapartesobres
Summary of the content on the page No. 12
Summary of the content on the page No. 13
NOTE: If your cabinet has glue blocks or other obstructions, cut out corresponding areas on the template to clear them. Do not cut out or cut through the screw holes in the template. CAUTION: We recommend safety glasses be worn while drilling screw holes to prevent the possibility of eye injury. 2. Drill three 1/4" diameter holes through the underside of the cabinet. TIP: On wooden cabinets you may want to mark and start the drill holes with awl or an awl. Be sure to hold the drill very firmly a
Summary of the content on the page No. 14
Summary of the content on the page No. 15
Summary of the content on the page No. 16
SPACEMAKER® UNIT SETUP DAY/TIME SETUP The day/time display has a 7-day a week and 12-hour format with an AM/ PM indicator. All messages recorded by the answering system will be stamped according to this clock. 1. Press and hold the DAY/TIME CHECK button to set the day of the week. 2. Press and hold the HOUR button to set the hour. 3. Press and hold the MIN button to set the minute. When you press and hold the MIN button, the time advances in 5-minute intervals. 4. Press and release the day/check
Summary of the content on the page No. 17
2. Use the CID VOL(+) / CID VOL(-) arrow keys to select ENG (English), FRA (French) or ESP (Spanish). English is the default. 3. Press the flash/program button to store (if a change is made, you will hear a confirmation tone). LOCAL AREA CODE 1. When speakerphone is OFF (not in TALK mode), press flash/program button and CID VOL(+) / CID VOL(-) arrow keys to move the pointer > to point at SET AREA CODE, press flash/program button to show SET AREA CODE - - - with the first digit blinking. SET
Summary of the content on the page No. 18
DISPLAY CONTRAST 1. When speakerphone is OFF (not in TALK mode), press flash/program button and CID VOL(+) / CID VOL(-) arrow keys to move the pointer > to point at SET CONTRAST, press flash/program button to show SET CONTRAST 1 2 3. SET CONTRAST >1 2 3 2. Use the CID VOL(+) / CID VOL(-) arrow keys to select 1, 2 or 3, the display contrast of text and background. Contrast level 1 is the default. NOTE: As you scroll through the contrast settings, the display contrast changes according
Summary of the content on the page No. 19
1. When speakerphone is OFF (not in TALK mode), press flash/program button and CID VOL(+) / CID VOL(-) arrow keys to move the pointer > to point at RING TO ANSWER, press flash/program button to show RING TO ANSWER 3 4 5 6. RING TO ANSWER 3 4 >5 6 2. Use the CID VOL(+) / CID VOL(-) arrow keys to select the desire rings to answer. Default is 5. 3. Press the flash/program button to store (if a change is made, you will hear a confirmation tone). SETTING THE SECURITY CODE FOR REMOTE
Summary of the content on the page No. 20
1. When speakerphone is OFF (not in TALK mode), press flash/program button and CID VOL(+) / CID VOL(-) arrow keys to move the pointer > to point at DEFAULT SETTING, press flash/program button to show DEFAULT SETTING. DEFAULT SETTING YES >NO 2. Use the CID VOL(+) / CID VOL(-) arrow keys to select YES or NO. NO is the default. 3. Press the flash/program button to confirm. 4. If you select YES, you will hear a confirmation tone, and the Spacemaker® Unit resets to the following default values:
