Summary of the content on the page No. 1
3-211-536-E2 (1)
Trinitron Color TV
GB
Operating Instructions
• Before operating the unit, please read this manual thoroughly and retain
it for future reference.
KV-SZ292
KV-SZ252
M91
© 2007 Sony Corporation
01GB01COV-SOEMMIX.p65 1 19/06/2007, 09:28 AM
Black
Sony KV-ZZ292M91 Group H7 (GB)_3-211-536-E2 (1)
Summary of the content on the page No. 2
A Specifications KV-SZ252M91 Note KV-SZ292M91 Power requirements 220-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 Stereo/Bilingual stereo NICAM Stereo/Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G Teletext language English, Russian Channel coverage B/G VHF : E2 to E12 /UHF : E21 to E69 / CATV : S01 to S03, S1 to S41 UHF : B21 to B68 /CATV : S01 to S03, S1 to S41 I VHF : C1 to C12, R1
Summary of the content on the page No. 3
B WARNING • Dangerously high voltages are present inside the TV. • TV operating voltage: 220 – 240 V AC. • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. • To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immedia
Summary of the content on the page No. 4
C Securing the TV To prevent the TV from falling, use the supplied screws and band to secure the TV. 20 mm 3.8 mm screws band Screw the band to the TV stand and to the provided hole at the rear of your TV. or (1) Screw one end of the band to the provided hole at the rear of your TV. (2) Securely fix the attached band to a wall or pillar using an attachment which can hold the TV. or (1) Attach each end of a cord or chain to the provided holders at the rear of your TV. (2) Securely fix the attache
Summary of the content on the page No. 5
b b D Getting Started 1 Step 1 Insert the batteries (supplied) into the remote. • Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. • Your TV can receive both TV and FM radio signals from the appropriate connections through the 8 (antenna input) terminal (see F). • You can also connect your TV to other optional components (see F). Step 3 Plug in the power cord, then press 1 on the TV to turn it on
Summary of the content on the page No. 6
E Setting up your TV (“Initial Setup”) When you turn on your TV for the first time, the “Initial Setup” menu will appear. You can adjust settings below using the buttons on the remote control or TV front panel. Press V , v , B or b to select or adjust items, then press . Select the desired menu language. 1 Initial Setup Select “Yes” to preset the channels automatically. First please connect 2 cable/ antenna To skip automatic channel presetting, select “No”. Start Auto Program now? Yes No Select
Summary of the content on the page No. 7
L R F Connecting optional components You can connect a wide range of optional components to your TV. Connecting cables are not supplied. Connecting to the TV (front) Audio/Video cable Camcorder L (MONO) R 2 L (MONO) R 2 Headphones Connecting to the TV (rear) TV, CATV, Satellite 1 Antenna Y cable CB (MONO) L (MONO) L or CR If cannot receive R R FM signal Antenna FM selector signal Audio Component cable Video cable TV signal Antenna Audio/ cable Video cable Audio/ Video cable Y RL L R CR CB L R V
Summary of the content on the page No. 8
G TV buttons and remote control 1 1 Turn off or turn on the TV. Wake Up indicator. 2 2 1 Standby indicator. 3 Remote control sensor. 4 PROG +/– Select program number. 5 2 +/– Adjust volume. 6 t Select TV or video input. WEGA GATE menu operations (see J) Select or adjust items. 4,5 , , , FM PROG Confirm selected items. 6 7 WEGA GATE Display or cancel WEGA GATE 8 765 4 3 2 1 menu. FM Listen to FM radio (see H). 8 0 1 ?/1 Turn off temporarily or turn on the TV. 2 a Display the TV prog
Summary of the content on the page No. 9
qd t Select TV or video input. qf 0-9 Input numbers. For program numbers 10 and above, enter the second digit within two seconds. ql Select sound mode options with a 5-Band Graphic Equalizer display: L “Dynamic”, “Standard”, “Custom”* (see ). Dynamic Standard Custom 100 300 1k 3k 8k 100 300 1k 3k 8k 100 300 1k 3k 8k * When the “Custom” mode is selected, you can receive the last adjusted sound settings from the “Sound Adjustment” option in the menu. w; Select picture mode options: “Vivid”,
Summary of the content on the page No. 10
H Listening to the FM Radio You are able to listen to the FM radio stations using your TV by connecting an antenna (see F). To access to FM Radio mode: Press WEGA GATE button and select “FM Radio” (see J). or Press FM button on the front panel (see G). To exit from FM Radio mode: Press WEGA GATE button, select the desired items: “TV” or “External Inputs”, then press . Select the desired TV channel or external inputs and press . or Press FM button on the front panel. Listening to preset s
Summary of the content on the page No. 11
I Troubleshooting If you find any problem while viewing your TV, you can either use the “Factory Settings” function (see N) or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. Snowy picture, noisy sound • Check the antenna setup and other connections. • Preset the channel manually again (see M). • Set the “Signal Booster” to “Auto” (see M) or try using an external booster. Distorted picture, noisy sound • Set the “Signal Booster” to “Off” (see M), or turn
Summary of the content on the page No. 12
Troubleshooting (continued) TV cannot receive stereo broadcast sound or stereo broadcast sound switches on and off or is distorted. • Check the antenna setup and other connections. TV cannot receive FM radio station. • Connect a separate FM antenna and the TV channel source through an antenna selector (switch) to your TV (see F). The 1 (standby) indicator on your TV flashes red several times after every three seconds. • Count the number of times the 1 (standby) indicator flashes. Press 1 on the
Summary of the content on the page No. 13
J WEGA GATE navigator WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs, FM Radio mode and “Settings” menu. WEGA GATE TV TV 01 External Inputs 02 “TV” FM Radio 03 watch the preset TV Settings 04 channels (see E) 05 Select Select Confirm Confirm End External Inputs 1 Video 1 2 Video 2 “External Inputs” select the inputs for the DVD connected equipment (see F) Select Confirm End FM Radio listen to the FM radio Preset 1: “FM Radio” ---.-- (see H) Please
Summary of the content on the page No. 14
K “Picture” setting Press WEGA GATE and select “Settings”. Picture Picture Mode: Vivid Make sure the “Picture” icon ( ) is selected, Picture Adjustment Color Temperature: Cool then press . VM: High Intelligent Picture: On Signal Level Indicator: On Select Confirm End “Picture Mode” Choose either “Vivid” (bright, contrast and sharp), “Standard” (normal) or “Custom”*. “Color Temperature” Adjust white color tint. Choose either “Cool” (blue tint), “Neutral” (neutral tint) or “Warm” (red tint). “VM”
Summary of the content on the page No. 15
“Picture” setting (continued) Adjusting the “Picture Adjustment” items under “Custom” mode Press V or v to select either “Picture” (contrast), “Brightness”, “Color”, 1 “Hue” (color tones) or “Sharpness”, then press . Selecting “Reset” will set your TV to the factory settings. Press V,v,B or b to adjust the setting of your selected item, then press . 2 Repeat the above steps to adjust other items. 3 The adjusted settings will be received when you select “Custom”. • “Hue” can be adjusted for the N
Summary of the content on the page No. 16
L “Sound” setting Press WEGA GATE and select “Settings”. Sound Sound Mode: Dynamic Press V or v to select the “Sound” icon ( ), Sound Adjustment Balance then press . Intelligent Volume: Off Surround: Off Select Confirm End “Sound Mode” Choose either “Dynamic” (low and high tones), “Standard” (voice and high tones) or “Custom”* “Balance” Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. “Intelligent Volume” Adjust the volume of all program numbers and video
Summary of the content on the page No. 17
M “Channel Setup” setting Channel Setup Press WEGA GATE and select “Settings”. Auto Program Press V or v to select the “Channel Setup” Manual Program Program Sorting/Edit icon ( ), then press . FM Radio Setup Select End Confirm “Auto Program” Preset channels automatically. “Manual Program” Manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually). “Program Sorting/Edit” Sort and edit the channels. (a) If you wish to keep the channels in
Summary of the content on the page No. 18
“Channel Setup” setting (continued) “FM Radio Setup”* Preset up to nine FM radio stations. You can manually preset each FM radio station that can be received in your area and then store the radio frequency of the desired FM radio stations. (1) Press V or v to select the desired FM radio station position, then press . (2) Press V or v to search the FM radio stations. Searching stops automatically when a station is tuned in. If the station has a noisy sound, you may be able to improve the sound qu
Summary of the content on the page No. 19
Presetting channels manually After selecting “Manual Program”, select the program 1 Manual Program number to which you want to preset a channel. Program: 01 TV System: D/K (1) Make sure “Program” is selected, then press . VHF Low Fine: Auto (2) Press V or v until the program number you want Signal Booster: Auto to preset appears on the menu, then press . Select Confirm End Select the desired channel. 2 (1) Make sure either “VHF Low”, “VHF High” or “UHF” is selected, then press . (2) Press V or
Summary of the content on the page No. 20
N “Setup” setting Setup Press WEGA GATE and select “Settings”. Language: English Picture Position Press V or v to select the “Setup” icon ( ), Video Label then press . Color System: Auto Factory Settings Select Confirm End “Language” Change the menu language. Press V or v to select either “English” or “Русский” (Russian), then press . “Picture Position” Adjust the picture position when it is not aligned with the TV screen. Press V or v to select “Picture Rotation” or “Picture V-Position”, then p
