Daewoo 14Q3 user manual

User manual for the device Daewoo 14Q3

Device: Daewoo 14Q3
Category: CRT Television
Manufacturer: Daewoo
Size: 1.67 MB
Added : 6/17/2014
Number of pages: 77
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Daewoo 14Q3. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Daewoo 14Q3.

For your convenience

If looking through the Daewoo 14Q3 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Daewoo 14Q3 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Daewoo 14Q3 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Daewoo 14Q3 User manual - Online PDF
Advertisement
« Page 1 of 77 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Daewoo 14Q3 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Daewoo 14Q3. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Service Manual
38 / 48 / 51 Cm Mono Colour Television
CHASSIS : CP-370
MODEL : 14Q1/20Q1/21Q1
14Q2/20Q2/21Q2
14Q3/20Q3/21Q4
14T1/20T1/21T1
14T2/20T2/21T2
14T3/20T3
@@
DAEWOO ELECTRONICS CO., LTD.

Summary of the content on the page No. 2

CONTENTS Specifications ................................................................................................................ 1 Safety Instruction ......................................................................................................... 2 Circuit block Diagram ................................................................................................. 3 Alignment Instructions ................................................................................

Summary of the content on the page No. 3

Specifications Q : 1SPEAKER MODEL, T : 2SPEAKER MODEL VM : WITHOUT TXT. MODEL, TM : WITH TXT. MODEL TV Standard PAL/SECAM-B/G, D/K, I, H, NTSC-3.58/4.43 Mains Voltage 100~250V AC, 50/60Hz Power Consumption 14”Q = 69W, 14”T = 74W 20”Q = 79W, 20”T = 84W 21”Q = 79W, 21”T = 84W Sound output . 1 Speaker : 3W( at 80% MOD. 10% THD) . 2 Speaker : 4W + 4W( at 80% MOD. 10% THD) Speaker . 1 Speaker : 3W, 16 ohm . 2 Speaker : 7.5W, 8 ohm(2EA) Antenna 75 ohm unbalanced Impedance

Summary of the content on the page No. 4

Safety Instruction WARNING: Before servicing this chassis, read the “X-RAY RADIATION precaution”, “safety precaution” and “product safety notice” below. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially voltage should be checked. It is recommended hazardous X-RAY RADIATION.To avoid such the reading of the high voltage recorded as a part hazards, the high voltage must not exceed the of the service records. it is important to use an specified limit. The nominal value of

Summary of the content on the page No. 5

Alignment Instructions 1. AFT 1.1 Standard B/G,D/K,I 1) Set a Signal Generator with - RF FREQUENCY = 38.9 MHz, - RF OUTPUT LEVEL = 80 5 dBuV - System = PAL / SECAM - B/G, D/K, I NTSC - 3.58/4.43 2) Connect the Signal Generator RF Output to P101 (Tuner IF Output). There must be no signal input to the tuner. 3) Press the “AFT” KEY and wait until the TV screen display “AFT OK”. 2. AGC 1) Set a Pattern Generator with RF LEVEL 63° 2 dBuV . 2) Connect a OSCILLOSCOPE PROBE to P102 (TUNER AGC INPU

Summary of the content on the page No. 6

6. GEOMETRY 6.1 VERTICAL CENTER 1) Set the TV to NOR I mode. 2) Pressing the V-SIZE UP/DOWN KEY, the lower half of the screen is blanked. 3) Adjust the border line of blanked picture coincident with the mechanical center marks of the CRT using the V-CENTER UP/DOWN KEY. 6.2 VERTICAL SIZE The VERTICAL CENTER adjustment has to be done in advance. 1) Apply a RETMA PATTERN signal. 2) Set the TV to NOR I mode. 3) Adjust the upper part of the picture with the V-SIZE UP/DOWN keys. 6.3 VERT

Summary of the content on the page No. 7

If EEPROM(1703) has been changed ; - Option data has to be changed and - all alignment function has to be readjusted. The initial state of adjustment are as follows; - V-Center, V-Slope V-Size, H-Center, R, G, B, AFT = Center (30/64 - 33/64) - S-Correction = 00/64 - AGC = 15~60/64 Service Remocon 6

Summary of the content on the page No. 8

IC Description DW370ASM* (Micro-controller for Non-Teletext Model) =TMS370C08A05 ( TI Type No.) (1) General Description The TMS370C08A05 devices are members of the cMCU370 family single-chip microcontrollers. The cMCU370 family provides cost effective real-time system control through use of the PRISM methodology. The PRISM methodology modular fabrication process integrates analog, digital, linear and power technologies on a single chip, thereby maximizing the total integration strategy. Th

Summary of the content on the page No. 9

• 09 CMOS Compatible I/O Pins - All Peripheral Function Pins Software Configurable for Digital I/O - 6 Bidirectionals, 3 Input Pins • Plastic 42 YSDP Pins Package (3) Block Diagram 8

Summary of the content on the page No. 10

DW5255M*(Micro-controller & West/East Teletext Decoder) DW5255RM*(Micro-controller & Cyrillic Teletext Decoder) =SDA5255-A*** (SIEMENS Type No.) (1) General Description The TDA5255 contains a slicer for VPS and TTX, an accelerating acquisition hardware module, a display generator for “LEVEL 1” TTX data and a 8 bit u-controller running at 333 nsec cycle time. The controller with dedicated hardware guarantees flexibility, does most of the internal processing of TTX acquisition , transfers data

Summary of the content on the page No. 11

• Controller: - 8 bit configuration - 18 MHz internal clock - 0.33 us instruction cycle - eight 16-bit data pointer registers (DPTR) - two 16-bit timers - watchdog timer - serial interface (UART) - 256 bytes on-chip RAM - 1 Kbyte on-chip extended RAM (access via MOVX) - 8 Kbyte on-chip ACQ-buffer-RAM (access via MOVX) - 6 channel 8-bit pulse width modulation unit - 2 channel 14-bit pulse width modulation unit - 4 multiplexed ADC inputs with 8-bit resolution - one 8-bit I/O port with open drain o

Summary of the content on the page No. 12

(4) Pin Description * A : DW5255M*/DW5255RM*, *B : DW370ASM* Pin Name Description Symbol A* B* A* B* A* B* 1 1 P3.1 T1IC1/CR SYS NTSC OUT for switching SAW filter K6259 - PAL/SECAM : L - NTSC : H 2 2 P0.7/Open Drain A0 BUSSTOP I2C BUS STOP IN for Computer controlled alignment in Factory ( Active Low ) 3 3 P0.6/Open Drain A1 SDA Serial data IN/OUT for I2C 4 4 P0.5/Open Drain A2 SCL Serial clock IN/OUT for I2C 5 5 P0.4/Open Drain A3 OPTION #5 #6 Teletext #6 6 6 P0.3/Open Drain A4 OPTION H

Summary of the content on the page No. 13

Pin Name Description Symbol A* B* A* B* A* B* 30CVBS CVBS CVBS IN 31 P2.3/8 bit ADC Not Used 32 22 P2.2/8 bit ADC B0/AN0/ADC AGC IF AGC INPUT for Auto Tuning System 33 23 P2.1/8 bit ADC B1/AN1/ADC KS Local KEY SCAN IN 34 24 P2.0/8 bit ADC B2/AN2/ADC S/SW Not Used 35 25 VSS VSS-OSD VSS Ground 36 26 P3.3/INT1 INT1 IR REMOTE IR IN 37 27 VDD VCC-OSD VDD Power Supply 38 28 LCIN OSCIN-OSD LCIN CLOCK IN for OSD 39 29 LCOUT OSCOUT-OSD LCOUT CLOCK OUT for OSD 40 30 P3.7/TXT I/O T2EVT/PWM2 BL BAND VHF

Summary of the content on the page No. 14

24LC08B (EEPROM) (1) Features • Single supply with operation down to 2.5V • Page-write buffer for up to 16 bytes • Low power CMOS technology • 2ms typical write cycle time for page-write - 1mA active current typical • Hardware write protect for entire memory - 10 A standby current typical at 5.5V • Can be operated as a serial ROM - 5 A standby current typical at 3.0V • Factory programming(QTP) available • Organized as two or four blocks of 256 bytes • ESD protection > 4,000V (2x256x8) and (4x256

Summary of the content on the page No. 15

TDA8374A (Single chip TV Processor for Negative modulation IF ) TDA8374 (Single chip TV Processor for Negative & positive modulation IF) (1) General Description The TDA8374(A) is I2C-bus controlled single chip TV processors which are intended to be applied in PAL/NTSC television receiver. The IC is mounted in a S-DIL 56 envelope. (2) Feature • IF - Vision IF amplifier with high sensitivity and good figures for differential phase and gain - PLL demodulator with high linearity offering the po

Summary of the content on the page No. 16

(3) Block Diagram 15

Summary of the content on the page No. 17

(4) Pin Description No Name Description 1 SOUND IF INPUT The sound equivalent input impedance is 8k5 ohm // 5pF which has to be taken into account for proper termination of the ceramic filters. The DC impedance is very high. The minimum input signal for catching is l mV rms. 2 EXT AUDIO INPUT An external sound signal (500mVrms) for example from SCART can be applied to this pin via a coupling capacitor. The input impedance is 25kohm. 3 VCO REF FILTER The IF VCO tuned circuit is applied to the

Summary of the content on the page No. 18

No Name Description A voltage detection circuit is connected to both pins. - pin12 if V12 <6.8V than a power on reset, POR, is generated. The Hout output is disabled immediate. - pin37 if V37 <5.8V than the horizontal output is disabled immediate. 13 INT CVBS INPUT It is recommended that the CVBS1 int and CVBS2 ext input amplitudes are 17 EXT CVBS INPUT 1 Vpp (inclusive sync amplitude). This, because the noise detector switches the 1 loop to slow mode (i.e. auto 1mode when FOA, FOB = 0,0)

Summary of the content on the page No. 19

No Name Description to the luminance input pin 27. The pin is internally AC coupled to the luminance clamp via a capacitor of 50pF; clamping action occurs during burstkey period. 28 LUMINANCE The luminance output signal is approximately l V black-white with typical OUTPUT output impedance of 25O ohm. 29 B-Y OUTPUT The maximum output impedance of pins 29 and 30 is 500 when PAL/NTSC 30 R-Y OUTPUT signals are identified. When SECAM is identified by the SECAM add-on and no PAL/NTSC is already ide

Summary of the content on the page No. 20

No Name Description A flash protection becomes active when this pin is forced >6V. The horizontal drive is switched-off immediately. Once the voltage is <6V the horizontal drive is switched-on again via the slow start procedure. 43 PHI-1 FILTER The loopfilter connected to pin 43 is suitable for various signal conditions as strong/weak and VCR signal. This is achieved by switching of the loopfilter time constant by changing the PHI-1 output current. Via I2C bus FOA/B, different time constant


Alternative user manuals
# User manual Category Download
1 Daewoo 14Q2 User manual CRT Television 30
2 Daewoo 20T1 User manual CRT Television 29
3 Daewoo 20Q2 User manual CRT Television 56
4 Daewoo 20T2 User manual CRT Television 37
5 Daewoo 14T2 User manual CRT Television 1
6 Daewoo 20Q3 User manual CRT Television 4
7 Daewoo 14T1 User manual CRT Television 0
8 Daewoo 20Q1 User manual CRT Television 8
9 Daewoo 21Q1 User manual CRT Television 1
10 Daewoo 21Q2 User manual CRT Television 10
11 Daewoo 21Q4 User manual CRT Television 0
12 Daewoo 21T1 User manual CRT Television 10
13 Daewoo 21T2 User manual CRT Television 12
14 Daewoo CP-885F User manual CRT Television 4
15 Daewoo CP005P-010G1 User manual CRT Television 2
16 Sony BRAVIA 32EX308 User manual CRT Television 10
17 Sony E42A10 User manual CRT Television 3
18 Sony FD Trinitron KV-21FX20K User manual CRT Television 58
19 Sony BRAVIA KDL-26T30 User manual CRT Television 7
20 Sony BRAVIA 46HX701 User manual CRT Television 4