Summary of the content on the page No. 1
Installation Instructions
Model CCDF
Color Camera External Mount
CCDF FEATURES:
High Resolution, 1/3”CCD Color Camera
Compact Zinc Alloy Die Cast Body
Waterproof Housing
Waterproof Microphone
Adjustable Mounting Angle
Wide Angle Lens
Flush Mount or Surface Mount
128-6951
1 of 12
Summary of the content on the page No. 2
Color Camera View: Cable Connector End View: 1 128-6951 2 of 12
Summary of the content on the page No. 3
Specifications: 1. Signal System: NTSC 2. Voltage: DC12V 3. Current: 80mA 4. Image Sensor: 1/3” CCD Color Sensor NTSC: 510 X 492 picture elements 5. Horizontal Definition: 420 Lines 6. Viewing Angle: 120 degrees 7. Minimum Illumination: 0.8 LUX 8. Outer Dimensions: 1.18”(W) x 1.10”(H) x 1.65”(D) 9. Weight: 2.5 Oz 2 128-6951 3 of 12
Summary of the content on the page No. 4
Contents: 3 128-6951 4 of 12
Summary of the content on the page No. 5
Contents Description: 1. Camera: 1 8. Slant Washer 1: 1 2. Support Bracket: 1 9. Slant Washer 2: 1 3. Lock Nut: 1 10. Tapping Screw: 2 4. Protective Cover: 1 11. Combine Screw: 2 5. Top Cover: 1 12. Washer: 2 6. Flat Washer 1: 1 13. Docking Nut: 2 7. Flat Washer 2: 1 4 128-6951 5 of 12
Summary of the content on the page No. 6
Flush Mount Note: 1. Camera 3. Lock Nut 5. Top Cover 6. Flat Washer 1 14. Mounting Plate 5 128-6951 6 of 12
Summary of the content on the page No. 7
Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Use a 7/8” hole saw to drill the mount ing hole. 2. Screw the lock nut with the threaded side toward the camera body in the showed direction, then put the camera neck through the mounting hole with the lens exposed and wire cable facing down. 3. Place the flat washer 1 (# 6) and top cover (#
Summary of the content on the page No. 8
Angle Flush Mount Size of Mounting Holes (See the Attached Page) Note: 1. Camera 3. Lock Nut 5. Top Cover 7. Flat Washer 2 8. Slant Washer 1 9. Slant Washer 2 7 128-6951 8 of 12
Summary of the content on the page No. 9
Angle Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Drill four 1/8” positioning holes and one 7/8” mounting hole at the mounting location according to the drawing of Size of Mounting Holes. 2. Screw the lock nut (# 3) and the flat washer 2 (# 7) with the non-threaded side to the camera neck in the showed direction. 3. Mount the slant was
Summary of the content on the page No. 10
Surface Mount Note: 1. Camera 2. Support Bracket 3. Lock Nut 4. Protective Cover 5. Top Cover 6. Flat Washer 1 11. Combine Screw 12. Washer 13. Docking Nut 9 128-6951 10 of 12
Summary of the content on the page No. 11
Surface Mount Installation: 1. Locate suitable mounting location in the rear center of the vehicle and use the support bracket (# 2) as a template to mark and drill two 5/32” holes on the mounting location. 2. Put the support bracket (# 2) onto the camera neck, then screw the lock nut along the camera neck to secure the bracket (# 2) to the camera body (# 1) in the showed direction. 3. Screw the combine screws (or tapping screws) into the holes to attach the camera support bracket to the vehicle
Summary of the content on the page No. 12
© 2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6951 128-6951 12 of 12
