Our goal is to provide you with a quick access to the content of the user manual for Panasonic WV-CL920. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Panasonic WV-CL920.
If looking through the Panasonic WV-CL920 user manual directly on this website is not convenient for you, there are two possible solutions:
Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Panasonic WV-CL920 but the selected pages only. paper.
Below you will find previews of the content of the user manuals presented on the following pages to Panasonic WV-CL920. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.
WV-C CL924 L924
Color CCTV Cameras
Model No. WV-CL920
(Lens : option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
For U.S.A NOTE: This equipment has been tested and found to com- ply with the limits for a Class A digital device, pursuant to CAUTION Part 15 of the FCC Rules. These limits are designed to pro- RISK OF ELECTRIC SHOCK DO NOT OPEN vide reasonable protection against harmful interference when the equipment is operated in a commercial environ- ment. This equipment generates, uses, and can radiate CAUTION: radio frequency energy and, if not installed and used in TO REDUCE THE RISK OF ELECTRIC SHOCK,
CONTENTS PREFACE ...................................................................................................................................................................... 4 FEATURES .................................................................................................................................................................... 4 PRECAUTIONS ..............................................................................................................................
PREFACE Panasonic's WV-CL920 (WV-CL924) series digital color zontal pixels (picture elements), and digital signal pro- camera introduces a new level of high picture quality cessing LSI's. This model offers cutting-edge technolo- and high resolution through the use of a 1/2-inch frame gy for advanced video surveillance. interline transfer CCD image sensor having 768 hori- FEATURES 1. The following functions are built in. 6. High quality picture: (1) Auto Light Control (ALC)/Electronic Light (a) 2
PRECAUTIONS 1. Do not attempt to disassemble the camera. 5. Clean the CCD faceplate with care. Do not clean the CCD with strong or abrasive To prevent electric shock, do not remove screws or detergents. Use lens tissue or a cotton tipped covers. applicator and ethanol. There are no user serviceable parts inside. Ask a qualified service person for servicing. 6. Never face the camera towards the sun. Do not aim the camera at bright objects. Whether 2. Handle the camera with care. the camera is in
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector u Left Button ( ) This connector is used to connect the auto iris lens This button is used to move the cursor to the left. It with a 4-pin male connector supplied as a standard is also used to select the mode and can be used to accessory (Part No. YFE4191J100). adjust some levels. w Flange-back Adjusting Ring (FB) i Up Button ( ) This ring is used to adjust the back focal length or This button is used to move the cursor upward. It is picture focus. Rotate this ring upw
!3 Power Cord Socket Cautions: This socket is used to connect the power cord 1. Connect to 12 V DC (10.5 V-16 V) or 24 V AC (supplied as a standard accessory). (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND !4 AC/DC Compatible Input Terminal terminal when the power is supplied from a 24 V (DC 12V IN/AC 24V IN) AC power source. This terminal is for connecting the 12 V DC or 24 V 2. To prevent fire or electric shock hazard, use a AC power supply cord. U
CONNECTIONS Resistance of copper wire [at 20°C (68°F)] A. WV-CL920 (120 V AC 60Hz) 1. Plug the AC power cord (supplied as standard Copper wire #24 #22 #20 #18 2 2 2 2 size (AWG) (0.22 mm ) (0.33 mm ) (0.52 mm ) (0.83 mm ) accessory) into the AC Inlet Socket. 2. Connect the AC power cord to a 120 V AC 60 Hz Resistance 0.078 0.050 0.030 0.018 Ω /m outlet. Resistance 0.026 0.017 0.010 0.006 Notes: Ω /ft • Connect the power cord firmly. • The power cord should be long enough for pan- • Calculation o
2. 24 V AC Power Supply Video Cable Connect the power cable to the AC/DC compatible 1. It is recommended to use a monitor whose resolu- input terminal on the rear panel of the camera. tion is at least equal to that of the camera. 2. The maximum extensible coaxial cable length DC 12V AC 24V IN IN between the camera and the monitor is shown 1 below. 2 GND 24 V AC, 60 Hz Type of RG-59/U RG-6/U RG-11/U RG-15/U coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V) (19.5 V - 28 V) Recommended (m) 250 500 6
(2) Solder the lens cable to the pins of the supplied Installation of Auto Iris Lens Connector connector. Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below. The pin assignment of the lens connector is as fol- lows: Pin
Mounting the Lens Caution for Mounting the Lens Caution: The lens mount should be a CS-mount (1”-32UN). In Before you mount the lens, loosen the fixing screw case of a C-mount, it should be a C-mount adapter and on the side of the camera, and rotate this ring the lens weight should be less than 450 g (0.99 lbs). If upward until it stops. If the ring is not at the end, the lens is heavier, both the lens and camera should be the inner glass or CCD image sensor may be dam- secured by using the supp
FOCUS OR FLANGE-BACK ADJUSTMENT The following adjustment should be made by qualified 3. Tighten the screws on the side of the camera. service personnel or system installers. Caution: Tightening the screw by force will cause damage to the screw or deviation of focus. 1. Loosen the screw on the side of the camera. Flange-back Adjusting Ring Screw 2. Turn the flange-back adjusting ring to the desired position. Note: Adjusting a focus in the visible rays may be soft-focused with the near-infrared li
INSTALLATION OF CAMERA • Mounting from the top Fixing Screws Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the dia- gram, then mount the camera on the mounting Mount Adapter bracket. Make sure that the two original fixing screws are used when mounting the mount adapter as longer length screws may damage inner components. -14-
SETUP 1. CAMERA SETUP MENU This camera utilizes a user setup menu that is displayed on-screen. The setup menu contains various items that form a tree type structure. CAM SETUP Camera Light Electronic AGC Shutter SYNC Sensitivity ID Control ON(DNR-H)/ Enhancement Speed INT/LL ON/OFF ON(DNR-L)/OFF ALC ELC OFF/AUTO/FIX Camera PRESET PRESET ON PRESET PRESET ON VBS VS LL ID OFF (Back Light OFF (Back Light Automatic Automatic Manual Editing Compensation) Compensation) Selection Selection Selection
Lens Drive White Signal Motion Special Balance Selection Detector Menu ATW1 ATW2 AWC DC VIDEO BURST Manual Detection BW UP SIDE CHROMA AP PEDESTAL HUE Camera Mask Area Level (BW) DOWN GAIN GAIN Resetting Selection Adjustment AUTO1 AUTO2 ON OFF ON OFF Manual Display Mask Area Mode Selection -17-
Note: If no button is pressed for 6 minutes while the • Opening the Setup Menu CAM SET UP menu or any other menu is opened, Press and hold down for 2 seconds or more. the menu is automatically closed and the mode returns to the normal camera picture. Blinking ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC END SET UP DISABLE The CAM SET UP menu ap
Left Button (): Moves the cursor to the left. Use 2. SETUP OPERATION this button to select or adjust the This camera utilizes a user setup menu (CAM SET UP) parameters of the selected item. that is displayed on the monitor. The parameter changes each time To set items on the CAM SET UP menu, use the follow- this button is pressed. ing buttons on the side panel. Set Button (): Executes selection and displays a submenu for an item with mark. END: Close Setup menu. Up Button RET: Return to the prev
Important Notice: • Editing the CAM SET UP Menu When the cursor is moved to END and the CAM Important Notice: SET UP menu closed after changing the parame- When SET UP DISABLE appears in the bottom line ters, the new values are saved in the EEPROM of the CAM SET UP menu, you cannot change the (Electric Erasable and Programmable Read Only currently active settings. This is to prevent acciden- Memory). These values remain valid until new val- tal changing of the settings. ues are saved, even if th
SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Character Cursor Setting 0123456789 You can use the camera identification (CAMERA ID) to ABCDEFGHIJKLM NOPQRSTUVWXYZ Character assign a name to the camera. The camera ID consists ().,'":;!?= Area +-*/%$ of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor SPACE Command POSI RET END RESET screen. ................ Editing Pointer Area ** CAM SET UP ** CAMERA ID OFF
|1||Panasonic AJ- P||Digital Camera||36|
|2||Panasonic AJ-D215P||Digital Camera||37|
|3||Panasonic AJ-D900WP||Digital Camera||26|
|4||Panasonic AJ-D900WAP||Digital Camera||32|
|5||Panasonic AJ-D610WA||Digital Camera||11|