Summary of the content on the page No. 1
®
American DJ
User Instructions
24 Ch. DMX/Analog Programmable Touch Panel
TP-DMX24F ™
8
1 4 3 6 10 9 14 15 16
RECORD
CHASE
STEP
DIMMER
CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE FLASH BLIND
SECOND
1 2 3 4 5 6 7 8 9 10 11 12
MINUTE
0.1SEC
SIGNAL
MANUAL 10
PAGE 1
CHASE
STEP
1 SEC
STEP
3 SEC
^
8 5 SEC
^
PAGE 2 10 SEC
MIX
1 2 3 4 5 6 7 8 9 10 11 12 30 SEC
CHASE 6
1 MIN
2
3 MIN
4
5 MIN
AUDIO
REAL
PERCENT
2
TIME 10 MIN
TRAITS
CHASE
SHOW
0
TAP TIME
BLACK-
SYNC
13 14 15
Summary of the content on the page No. 2
CONTROLS AND FUNCTIONS Cont. 8 4 3 6 10 9 14 15 16 1 RECORD CHASE STEP DIMMER CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE FLASH BLIND SECOND 1 2 3 4 5 6 7 8 9 10 11 12 MINUTE 0.1SEC SIGNAL MANUAL 10 PAGE 1 CHASE STEP 1 SEC STEP 3 SEC ^ 8 5 SEC ^ PAGE 2 10 SEC MIX 1 2 3 4 5 6 7 8 9 10 11 12 6 30 SEC CHASE 1 MIN 2 3 MIN 4 5 MIN AUDIO REAL PERCENT 2 TIME 10 MIN TRAITS CHASE SHOW 0 TAP TIME BLACK- SYNC 13 14 15 16 17 18 19 20 21 22 23 24 OUT DIMMER CHASE AUDIO 12 13 11
Summary of the content on the page No. 3
CONTROLS AND FUNCTIONS Cont. 1 2 3 4 6 5 DMX OUTPUT DC INPUT AUDIO 1:GND 2:DATA- 3:DATA+ LINE INPUT +16V-+24V RANGE 2 1 500mA Min. 100MV-1VP-P - + 1:GND 2:DATA - 3 3:DATA + 1. DC INPUT 16-24V 220mA min 2. LINE INPUT (EXT AUDIO INPUT) JACK (lOOmV to 1 vp-p-p) 3. MIDI IN Receives MIDI data 4. MIDI OUT Transmit MIDI data output 5. MIDI THRU Repeats and sends MIDI input 6. DMX OUTPUT OPERATING INSTRUCTIONS There are 6 modes of operation plus BLACKOUT 1. MANUAL 2. PROGRAM 3. RECORD / CHASE 4. ASSI
Summary of the content on the page No. 4
OPERATING INSTRUCTIONS Cont.. 1. MAKE SURE THE TRANSFORMER IS CORRECT 16 TO 24 DC AND CORRECT POLARITY . 2.Plug in transformer and turn on unit. LED’s for HOLD / FLASH, TRAITS CHASE, PAGE 1 and DIMMER are on. you are now in MANUAL MODE 1. MANUAL MODE Touch any (FIG 2.) CHANNEL 1-24 BUTTON the LED will light and that channel is turned on, the maximum output is displayed on (FIG14.) LCD DIGITAL DISPLAY. You can touch (FIG 3.) CH 1-24 HOLD/FLASH for 0.5 sec until LED for HOLD is lit. This will ke
Summary of the content on the page No. 5
OPERATING INSTRUCTIONS Cont. 2.1 CHASE PROGRAM Cont. At this point you can set the duration between this and the next step in the chase if you want to do this. Use (FIG13.) CHASE FADER or touch (FIG 5.) REAL TIME /TAP SYNC, wait until the interval is what you want, then touch (FIG 5.) REAL TIME /TAP SYNC again. For most programs let the default setting of 0.3 be used. C. Touch (FIG 9.) RECORD CHASE for 0.5 sec. All LED’s will blink, then Channel LED’s will go out.This means the first step is mem
Summary of the content on the page No. 6
OPERATING INSTRUCTIONS Cont. 2.3 DIMMER SETTING IN MANUAL MODE To adjust DIMMING/VALUE of any channel in Manual mode. A. Enter CHASE PROGRAM mode, Touch any (FIG 2.) CHANNEL 1-24 when LED is on touch same channel again until LED starts to blink. You can now use (FIG12 ) DIMMER FADER to adjust output. Set as many CHANNELS as you want in this manner. B. Touch (FIG 9.) RECORD CHASE button for 0.5 sec until all LED’s blink. This means output has been memorized. 2.3.1 CODES The following are codes
Summary of the content on the page No. 7
OPERATING INSTRUCTIONS Cont. 3. RECORD / CHASE cont. There are 3 ways to control the chase program 1. CHASE, 2. AUDIO, 3. MANUAL 3.1. CHASE control A. Set (FIG13.) CHASE FADER to SHOW position > 10 min. The Chase will be controlled by what ever time was programmed in section 2.1 ( The default setting is 0.3 sec) B. Set (FIG13.) CHASE FADER to any position up to 10 min The Chase will be controlled by what ever time selected, all steps will be the same duration. C. Tap (FIG 5.) REAL TIME /TAP
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS Cont. MIDI SETTING AND RUNNING MIDI SETTING Touch and hold (FIG.1.) CHASE 9, CHASE 10, CHASE 11,CHASE 12, while power is being turned on. CHASE 1, CHASE 2, CHASE 3 LEDs blink rapidly and (FIG14.) LCD DIGITAL DISPLAY READS A AA AA A this means console is in MIDI mode. 1. CHASE 1 MIDI SEND / CHASE 2 MIDI RECEIVE Touch CHASE 1 or CHASE 2 the LEDs blinks and go out. MIDI channel is defined, as CHANNEL 1-16,CHANNEL 17-24 is not assigned. Touch any CHANNEL 1-16, LED lights the
