Summary of the content on the page No. 1
Otingpera i O nstructi ns
®
03 ™
S&G Z D-Drive Multi-User Electronic Safe Lock
2005 Series
©
03
™
The S&G X D-Drive lock combines ease of operation with • All codes end with #. This signals the
security and flexibility. Its advanced electronic circuit design lock that you have finished entering all
makes it easy to open and easy to change codes. Follow these digits of the code.
instructions carefully to get the best possible use from your lock.
• If you pause more than 10 seconds
I tcudortn I
Summary of the content on the page No. 2
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series 2. If the lock “chirps” when keys are pressed, but it will not t o o nep eht Lkco open, the batteries may be drained to the point that they Make sure the keypad is turned counterclockwise to stop. Press will not operate the lock’s solenoid. Follow the battery the code digits or letters in order, followed by #. Then, within six replacement procedure in this manual. seconds, turn the keypad clockwise abo
Summary of the content on the page No. 3
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series the time delay, for the opening code at the end of the time delay, o nep Ign teh Lkco or for both codes. The silent alarm signal will be sent each time a ➥WIth n o t Ime d e Lya duress code is entered. (Note: Lock codes 4 - 8 are not available if the duress feature is turned on. If time delay override is disabled or not used, lock A valid code is needed to open the lock. This is how to open the code 9
Summary of the content on the page No. 4
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series c gnah Ign , c taer Ign , d e Lte Ign c sedo ➥c gnah Ign y ruo o Wn c edo Any code holder can change his own code. The process is: ➥c tear Ign a m tnemegana r tese c edo ♪♪♪♪♪ ♪♪♪ ♪♪♪ 2 2 ✽ OLD CODE # NEW CODE # NEW CODE # A management reset code can only be created before the lock's master code is changed for the first time. It can later be used to For example, changing a user code of 2 2 2 2 2 2 to a new
Summary of the content on the page No. 5
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series ➥d e Lte Ign na e x Ist Ign c edo ➥c gnah Ign eht o nep Ign WIodn W d trau Ino The holder of the master code (position 0) can delete any other code. The length of the opening window period is set as follows. The period The master code cannot be deleted under any circumstances. can be anywhere from 1 to 10 minutes. ♪♪♪♪♪ ♪♪♪ The holder of the supervisor code (position 1) can delete user 7 4 ✽ master code # 0
Summary of the content on the page No. 6
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series After this programming procedure is completed, the lock will be ➥c tear Ign eht t Iem d e Lya o rrev Ied c edo disabled. If a valid code is entered, the lock will emit a double The TDO code is located in position 9. It is programmed as follows. beep, but will not open. ♪♪♪♪♪ ♪♪♪ 7 4 ✽ master code or supervisor code # 9 (position number) # ♪♪♪ ♪♪♪ ➥e ban LIgn eht Lkco In m tnemegana /e pm Leeyo a ssecc m e
Summary of the content on the page No. 7
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series ➥c ecna LLIgn u res d Ibas Le In m tnemegana /e pm Leeyo a ssecc m edo m gana Ign a du It t ar IL If you decide user code holders should no longer have the ability ➥c rupta Ign na a du It t ra IL to disable the lock, perform the following procedure. Your lock must have been ordered with this option. Using the audit ♪♪♪♪♪ ♪♪♪ ♪♪♪ 5 6 ✽ master code # 0 # 0 # trail feature also requires an optional keypad ext
Summary of the content on the page No. 8
Otingpera i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series Lo W b yretta c dno It Ino I tamrofn Ino t ba Lse © 03 ™ The S&G X D-Drive lock uses a 9-volt alkaline battery. We ➥d mrete In Ign y ruo Lkco ’s m edo fo o traep Ino ® recommend Duracell brand. If the battery in your lock needs to Enter 4 3 ✽ be replaced, twenty consecutive beeps will be heard after the The ensuing beep pattern will tell you if your lock is configured last number of the code and # have b
Summary of the content on the page No. 9
Btterya c hanging i nstructiOns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series Lo W b yretta c dno It Ino © 03 ™ The S&G X D-Drive lock uses one 9-volt alkaline battery, ® which is housed in the keypad. We recommend Duracell brand. If the battery needs to be replaced, the lock will emit five double-beeps whenever it is opened. If this signal is ignored and the battery becomes so weak that it will no longer operate the lock, you’ll hear twenty quick beeps when you enter a c
Summary of the content on the page No. 10
Btterya c hanging i O nstructi ns ® 03 ™ S&G Z D-Drive Multi-User Electronic Safe Lock 2005 Series Step 4—Carefully slide the battery behind the keypad, into the cavity that is designed to hold it (Figure 4). Be sure the battery has dropped all the way to the bottom of the cavity. Step 5—Gently place any excess wire into the cavity. Make sure it is not in a position to be caught between the keypad ring and the keypad base when the ring is pushed back against the base (Figure 5). Step 6—Once
Summary of the content on the page No. 11
Summary of the content on the page No. 12
WARRANTY Seller warrants that for one year from the date of shipment from Seller’s point of manufacture, the goods shall be free from defects in material and workmanship, provided the goods are normally and properly used according to the Seller’s written instructions. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. S&G DOES NOT WARRANT THAT THE GOODS ARE MERCHANTABLE OR FIT FOR ANY PARTICULAR PURPOSE EXCEPT AS EXPRESSLY PROVIDED HEREIN. Seller’s ent
