Fisher & Paykel DD24S user manual

Summary of the content on the page No. 1

(1,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM (1,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM
Installation instructions
DishDrawer®
US CA
DD24S models
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel d

Summary of the content on the page No. 2

Integrated DD24S Prefi nished Flat door DD24S Prefi nished L CD DD24S Integrated DD24S Prefi nished Flat door DD24S Prefi nished L CD DD24S (1,2) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM (1,2) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM 23 PRODUCT DIMENSIONS CABINETRY DIMENSIONS Installation diagrams for illustration purposes only Installation diagrams for illustration purposes only B B C K A D C H F I E G A C J F K H Cabinetry dimensions (inches (mm)) Produ

Summary of the content on the page No. 3

(2,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM (2,1) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM 4 PARTS SUPPLIED Edge Protector (1) Drain hose Drain hose Wire clip (1) Clamp (1) Top mounting Phillips Washer (1) Moisture protection support (1) joiner (1) brackets (2) 16 mm tape (1) (if service hole partition is metal) screws (7) (to prevent moisture damage) If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Exte

Summary of the content on the page No. 4

(2,2) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM (2,2) -1- 599625C DD24S installA2 USCA.indd 14/4/09 2:16:35 PM 6 OPTIONALLY HARD WIRING THE PRODUCT A B Remove the 2 2 access cover 1 3⁄16 ” (30 mm) 30 mm 4 5 1 1 6 3 8 7 Remove Power supply Ensure the drawer is removed and then rotated counter- Access cover clockwise to prevent kinked hoses. 8 7 CD Remove knock-out for cable 16 clamp. Fit suitable cable clamp for the conduit and terminate Ensure the drawer clips the wiring

Summary of the content on the page No. 5

(1,1) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM (1,1) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM 7 ROUTE THE HOSES AND MOVE INTO THE CAVITY A A B 3 3 1 OR 1 If top mounting brackets are being used, ensure they’re securely fitted before sliding optional product into cavity (x2) Ensure hoses and cord 2 are not kinked or twisted. 2 Tie together to avoid kinking. 1 8 REMOVE THE DRAWER AND SECURE THE PRODUCT A B 1 CC The product has three pairs of mounting bracket

Summary of the content on the page No. 6

(1,2) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM (1,2) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM 9 REFIT THE DRAWER A Ensure the drawer clips on 3 both sides are reset. 5 Before refitting the drawer, 4 ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. 4 Ensure the drawer is now rotated clockwise back. 1 2

Summary of the content on the page No. 7

29 ½ ” - 34 ¾ ” (750 - 882.5 mm) 29 ½ ” - 34 ¾ ” (750 - 882.5 mm) (2,1) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM (2,1) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM 10 PLUMBING AND DRAINAGE OPTIONS A DishDrawer® with Waste Disposal B DishDrawer® using Air Break C DishDrawer® and Standpipe 2 2 with Drain Hose Joiner 1 Ø 1 1/2” (38 mm) If space is limited for fixing, push If space is limited for fixing, push hose through drain hose support hose through drain ho

Summary of the content on the page No. 8

(2,2) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM (2,2) -2- 599625C DD24S installA2 USCA.indd 14/4/09 2:17:10 PM 11 FINAL CHECKLIST 12 TROUBLESHOOTING Check all parts are installed. Excessive water remaining above the filter plate, after the rinse cycle Ensure product is level, securely fastened to the cabinetry and opens and closes Check for kinked drain hoses or blocked waste connection, high loop not freely. The DishDrawer® must be free to fully close with no resistance fr