Summary of the content on the page No. 1
15” LCD TV with DVD Player
Operating Instructions
Model No. FPE1506DV
For assistance, please call: 1-800-645-4994
Or visit us at WWW.AUDIOVOX.COM
Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference
128-7697
Summary of the content on the page No. 2
Table Of Contents Important Safety Instructions--------------------------------------------------1 Characteristic Features ---------------------------------------------------------3 Disc Information -------------------------------------------------------------------4 Front Panel---------------------------------------------------------------------------5 Rear Panel----------------------------------------------------------------------------7 Remote Control-------------------------------------
Summary of the content on the page No. 3
Important Safety Instructions The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servici
Summary of the content on the page No. 4
Important Safety Instructions Note: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as
Summary of the content on the page No. 5
Characteristic Features This product incorporates a DVD player, LCD display and TV receiver in one system. Multiple Mode USB and CARD PORTS DVD mode Designed with USB and SD/MS/MMC card Component mode port, can be connected to USB device or VGA mode SD/MS/MMC Card. TV mode CVBS mode Auto TV Searching Function S-VIDEO mode Can be connected to the TV antenna, support Auto and manual TV programs searching High Quality Property function. High Resolution
Summary of the content on the page No. 6
Disc Information Discs Formats Supported By This Player DISC LOGO CONTENTS SIZE MAXIMUM TIME 133min(SS-SL) Audio+Video 242min(SS-DL) DVD 12cm (active picture) 266min(DS-SL) 484min(DS-DL) CD Audio 12cm 74min JPEG Still high resolution 12cm The operating method of some DVD discs is specified by the software maker. Please refer to the instruction manual of the disc. About Disc Terms Title Generally, pictures or music compressed on a D
Summary of the content on the page No. 7
Front Panel 1. 15" color TFT screen 15" color TFT screen clearly show the data. 2. SOURCE button Press to select the modes: DVD, Component, VGA, TV, CVBS or S-VIDEO. 3. MENU button Press to enter or exit setup menu. 4. CH ▲/ ▼ button In the TV mode, press to select channels. In setup menu, the same function as ▲/ ▼ direction buttons. 5. VOL ▲/ ▼ button In the TV mode, press to decrease or increase the volume. In setup menu, th
Summary of the content on the page No. 8
Front Panel 7. ■ STOP button Press to stop playback, then press the PLAY button to resume normal playback in DVD mode. Press the STOP button twice repeatedly to stop completely. 8. Eject button Press to eject the disc out. 9. Power button Press to enter or exit the standby mode. 10. SD/MS/MMC Card Port Insert the SD, MS or MMC card into the port. 11. Disc Tray Slot Used to load disc. 12. Earphone Jack When connected to earphone, the internal speakers will
Summary of the content on the page No. 9
Rear Panel 1. Y/Pb/Pr Input Jack 5. TV Signal Input Jack Connected to the Y/Pb/Pr input in Connected for the external NTSC TV Component mode. signal input. 2. L/R Audio Input Jack 6. DC 12V In Jack Connected to the L/R audio input in Connected to power adapter. Component mode. 7. VGA Input Jack 3. AV Output Jacks Connected to the VGA output jack on a Connected to the external AV input device. personal computer. 4. AV Input J
Summary of the content on the page No. 10
Remote Control Remote Control Drawing 1. POWER button Press to enter or exit the standby mode. 2. 0~9 Number buttons Press to select numbers. 3. LAST button In the TV mode, press to return to the channel last viewed. 4. MTS button Press to activate MTS function in TV mode. 5. VOL +/- button Press to increase or decrease the volume. 6. CC button In the TV or CVBS mode, press to display the closed captions or cancel display. 7. E
Summary of the content on the page No. 11
Remote Control Press to select numbers. For DVD Operation 6. Direction buttons ( ▲▼◄►) In the setup menu, press the ▲▼button to select the desired item and press the ◄► button to adjust or set. 7. ENTER button Press to confirm your selection. 8. TITLE button When a DVD disc is playing, press to go to title menu if the disc contains. 9. MENU button (in DVD mode) Press to enter the disc menu in DVD mode. 10. REPEAT button Press to repeat
Summary of the content on the page No. 12
Remote Control Preparation of Remote Control Using of Remote control Softly push the back cover to open the battery Point the remote control unit from no more than compartment. about 7m from the remote control sensor and within about 60 degrees of the front of the unit. Insert two batteries (1.5V, size AAA), please make sure the polarity matches the marks inside the compartment. Softly press the back cover to close it.
Summary of the content on the page No. 13
System Connections Do not connect the power cord until all other connections have been made. Ensure that you observe the color cord when connecting audio and video cables. Connecting to External AV Signal Source Use the audio and video cable to connect the AV input jacks on the rear panel of the unit to the external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the rear panel of the unit to the external AV signal source. After con
Summary of the content on the page No. 14
System Connections Connecting to External AV Signal Source YPbPr Use the audio and video cables to connect the Y/Pb/Pr input Jacks on the rear panel of the unit to the external AV signal source. After connection, turn on the power of the unit and external AV signal source and then press the SOURCE button to shift to Component mode. - 13 -
Summary of the content on the page No. 15
System Connections Connecting to External AV Device AV Out The unit supports AV signal output, it can be connected to the external audio and video devices. Use the audio and video cables to connect the AV output jacks on the rear panel of the unit to the external AV device. - 14 -
Summary of the content on the page No. 16
System Connections Connecting to PC The unit can be connected to PC (person computer) via the VGA cable. Follow the steps and the figure below to connect: 1. Connect one end of the VGA cable to the VGA input jack on the rear panel of the unit. 2. Connect the other end to the PC. 3. Connect one end of the audio cable to the PC audio input jack on the rear panel of the unit. 4. Connect the other end to the PC audio output jack. 5. Please set the PC’s resolution at 1024
Summary of the content on the page No. 17
System Connections Connecting to Earphones This unit can be connected to an earphone for listening to music privately. See the below figure for derails: After connecting to the earphone, the internal speakers output will turn off automatically. Connecting to Power Supply Plug the power supply cord to the AC100~240V wall outlet. - 16 -
Summary of the content on the page No. 18
System Connections Connecting to Car Adapter Power also can be supplied through the DC power adapter (Car Adapter), one end is connected to the DC 12V IN jack on the rear panel of the unit, the other end to the vehicle’s 12V accessory/Cigarette Lighter Socket, as shown on the below: Attention Do not operate the unit or view video software while driving a vehicle. Place the unit in a proper position for viewing. We advise you
Summary of the content on the page No. 19
System Connections Connecting to TV Antenna This unit can be connected to the TV signal input source via the TV jack on the rear panel. After connection, turn on the power to the unit, press the SOURCE button to shift to TV mode. After connecting to the antenna, turn on the unit, and go on with program searching, you can follow the below steps to select channels: 1. For 0~9 channel: Press the number buttons to select the channel
Summary of the content on the page No. 20
TV Function Preparations 1. After connection, press the POWER button to turn on the power. (If it is turned on, the power indicator is blue.) 2. Press the SOURCE button to shift to TV mode. You can go on with the following operations: Image Setting Note: This item is only available when there is signal input. Press the MENU button once to enter the setup menu, as shown on the right: In the setup menu, press the ▲▼ button to select Image and then
