Summary of the content on the page No. 1
DIGITAL RECORDING SYSTEM user manual
SPR-9816/9716
DIGITAL RECORDING SYSTEM
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive a more comprehensive service,
please register your product at
www.samsung.com/global/register
AB82-01978A Rev-00
SPR-9816-9716.indb 1 2008-07-03 오후 2:46:17
Summary of the content on the page No. 2
key features of your DVR The SHR-9816/9716 compresses up to 16 video input signals using an advanced MPEG4 codec and up to 16 audio input signals using ADPCM for real-time simultaneous storage and playback from the hard drive. This unit is also capable of streaming these signals across various networks for remote monitoring. 16-Channel BNC Video Input Connectors NTSC/PAL Video Source Compatible Recording speed: 480 ips (NTSC) / 400 ips (PAL) using CIF resolutions (352x240 NTSC / 352x28
Summary of the content on the page No. 3
safety regulations Please adhere to these safely regulations for the proper use of the product and to prevent risk/damage to you or the unit. Do not use more than one multi-plug. Using too many multi-plugs can cause abnormal heat generation or fire. Do not place sources of liquids near the DVR. ie: vases, cups, medicine, etc. Liquids can present a fire hazard. Do not bend the power cord forcibly nor put a heavy material on it. This action could lead to a fire. Do not operate or s
Summary of the content on the page No. 4
before start This user manual provides information that are necessary in the use of the DVR, ranging from a brief introduction of the product to names, functions, and connection instructions of the components, menu configurations, and other information pertinent to product use. Please read and adhere to the following notices. SEC retains the copyright on this manual. This manual cannot be copied without prior written approval from the SEC. Samsung Electronics will not be held responsib
Summary of the content on the page No. 5
contents 03 DVR: Front View INTRODUCING YOUR REAL TIME DVR 04 DVR: Rear view 03 05 Installation INSTALLATION 05 06 Basic connections CONNECTING WITH OTHER DEVICES 07 Sensor connection 08 Alarm connection 09 RS485 Connection 06 10 Network connection 11 External keypad connection 12 Pos device connection 13 Live watch screen WATCH 14 Login screen 14 Camera channel 15 Database drive allocation 13 16 Resource/ptz/playback/log 18 Full screen 19 Live screen switch 20 1-Channel video playback 20 Camer
Summary of the content on the page No. 6
58 Event search ADVANCED SEARCH 59 Sequential search 60 Thumbnail search 61 Object search 58 62 Pos search 63 Backup BACKUP 64 Backup management 63 65 System recovery APPENDIx 67 WebDVR 70 SPR Smart viewer 77 Remote desktop control 65 78 Specifications 79 Outline drawings 80 Troubleshotings(FAQ) 02_ contents SPR-9816-9716.indb 2 2008-07-03 오후 2:46:19
Summary of the content on the page No. 7
01 INTRODUCING YOUR REAL TIME DVR introducing your real time DVR DVR: Front View With the Panel Closed With the Panel Open 2 3 1 1 Power 2 USB 3 DVD-RW Front and rear configurations of the system may change to reflect changes in specifications or other quality improvement purposes. introducing your real time DVR_03 SPR-9816-9716.indb 3 2008-07-03 오후 2:46:19
Summary of the content on the page No. 8
DVR: Rear View 2 3 4 5 6 7 1 8 9 10 11 12 13 14 15 16 17 18 1 Power Supply (AC 100-240V, 60/50Hz, 4A/2A) 2 Sensor Input (Alarm-In) Ports (16 ports) 3 Spot Monitor Out Ports (2 ports) 4 Camera Video Input Ports (16 ports) 5 RS485 Port 6 Alarm-Out Ports (4 ports) 7 Audio Input Port 8 Mouse Input Port (PS/2) 9 10 Printer Port (LPT1) Keyboard Input Port (PS/2) 11 12 COM Port (COM1) Internal VGA Port 13 USB Port (Ver. 2.0) 14 Ethernet Port (100 Mbps) 15 16 Microphone Input Port (two-way audio input)
Summary of the content on the page No. 9
02 INSTALLATION installation CHECKING INSTALLATION CONDITIONS Adhere to the following precautions when installing the unit. • Indoor use only. • Prevent water and liquids from coming in contact with the unit’s terminals. • Protect the unit from excessive impact and force. • Do not forcibly pull on the power cable. • Do not open or disassemble the unit. • Use within the rated power input/ output range only. • Use an approved power cable only. • For products that require a ground source alway
Summary of the content on the page No. 10
connecting with other devices BASIC CONNECTION 1 2 3 4 5 6 Using a coaxial cable, connect a camera(s) to Attach the appropriate power cord to the 1 2 the BNC port(s). power supply unit. 3 4 Connect a keyboard to the PS/2 port. Connect a printer to the LPT1 port. 5 6 Connect a mouse to a USB port. Connect a VGA monitor to the VGA port. Ensure the correct rated voltage is provided before powering the unit. Improp er voltage may cause malfunction and/or permanent damage to the system. Warning
Summary of the content on the page No. 11
02 CONNECTING wITh OThER DEVICES SENSOR (ALARm-IN) CONNECTION No.1 Sensor GND No.9 Sensor GND (Alarm-In) (Alarm-In) Your DVR system is capable of transmitting electrical signals to external devices when an event occurs. Mechanical or electrical switches can be connected to the Alarm-In and Ground (GND) ports. The individual Alarm-In ports can be configured from the System Setup menu as either NC (Normal Close) or NO (Normal Open). Alarm-In Connection 1. Connect one of the external device’s sig
Summary of the content on the page No. 12
ALARm (ALARm-OUT) CONNECTION Your DVR system is capable of activating warning lights, sirens, and other types of external devices. External device s can be connected to the unit's Alarm-Out and COM ports. Alarm Connection 1. Connect one of the external device's signal lines to the desired alarm (Alarm-Out) port. 2. Connect the remaining line to the COM port. • The alarms (Alarm-Out) operate in conjunction with the sensors (Alarm-In). When an event signal is received through a sensor, an elect
Summary of the content on the page No. 13
02 CONNECTING wITh OThER DEVICES RS485 CONNECTION It's possible to control an external device by the DVR using the RS485 interface for communication. The RS485 port can be used to control PTZ cameras, speed domes, keyboard controllers and other types of external devices. Connect the Rx+/Tx+ & Rx-/Tx- of the external device to the + & - of the RS485 port respectively. Check the polarity (+/-) when making the connection. Faulty wiring can damage both devices. Electrical Hazard: Please
Summary of the content on the page No. 14
NETWORK CONNECTION Ethernet/UTP Cable (CAT5) LAN/WAN Internet Switch Hub (100Mbps) Router Your DVR system supports network-based remote monitoring, remote search, remote control, and remote software upgrade. SEC recommends the use of the TCP/IP protocol and a switching hub for LAN/WAN applications. Network Cable Connection 1. Connect a Ethernet/UTP cable to the network port located at the rear of the system. 2. Connect the opposite end of the Ethernet/UTP cable to the switch hub. • Before con
Summary of the content on the page No. 15
02 CONNECTING wITh OThER DEVICES ExTERNAL KEYPAD CONNECTION The SSC-2000 keypad can be used to control up to 255 DVR and PTZ units. Connect the DVR's RS485 (+/-) port to the SSC-2000 keypad's RS485 port. • Turn the power off both units while connecting the SSC-2000. • Pay attention to the polarity of the RS485 connections. • Refer to the SSC-2000 manual when attempting a RS232 connection. • When using a keypad device, please ensure that communication settings for both the DVR and the keypad
Summary of the content on the page No. 16
POS DEVICE CONNECTION Camera Video Input RS232C Cable POS System V SI-PRO(Text Input Device) Video Output RS232C Cable Video Input RS232C Cable Your DVR system is capable of operating in conjunction with POS systems, enabling you to store and search video transactions at the point of sale. AVE’s VSI-PRO is needed to connect the POS device to the DVR. For details on connecting VSI-PRO with your DVR, please refer to VSI-PRO’s user manual. • VSI-PRO by AVE (www.americanvideoequipment.com) is a
Summary of the content on the page No. 17
03 MONITORING watch LIVE WATCH SCREEN Live Watch supports full screen and various split-screen confi gurations. From Live Watch, you will be able to control PTZ, perform 1ch instant playback and make a backup. The buttons located within the watch screen also provide access to the other menus.(search, setup, etc). 5 1 6 7 2 8 4 9 sensors, alarms, and other devices Video Display window 1 connected to the DVR. Displays the live video feeds on screen. Simply drag PTZ: Displays PTZ controls.
Summary of the content on the page No. 18
LOGIN SCREEN CAmERA CHANNEL Entering authorized user ID and password gives access to Camera Channel Display Icons search features, system setup, and other system functions. Entering an incorrect user ID and password, however, will 2 3 result in limited DVR functionality and control access. [C01] CAMERA01 1 Logging In 1. Click on the button. 2. Enter the user ID and password. 4 REC : M 5 1 Camera Type 3. Click OK to login. Indicates whether the camera is a normal camera or a PTZ camera.
Summary of the content on the page No. 19
03 MONITORING DATABASE DRIVE ALLOCATION Disabling an Allocated Database Drive 1. R ight-click on the allocated drive you wish to disable. Allocating a New Database Drive The drive color will turn from blue to grey. 1. L ogin as an administrator then double click on the icon. 2. You will then be prompted with the Database Drive Allocation window. 2. Click OK to disable the allocated drive. The drive color will turn red. 3. Left-click on a non-allocated drive (Free Size) and you will be p
Summary of the content on the page No. 20
Reallocating a Disabled Drive PTZ Tab 1. L eft-click your mouse on a disabled database drive and you will be prompted with a “Do you want to 1 format?” warning window. 2 3 4 5 A uto move 1 Automated PTZ movement functions. Auto Pan: T his button is used to initiate Auto Pan. AutoPan is a function where, after designating the start point and end point, the camera completes pan/tilt trips within the defi ned interval. Start: Starting position for the Auto Pan. End: Ending position for the
