Metra Electronics 99-7335S user manual

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7335S
APPLICATIONS
HYUNDAI Veracruz
2007-2010
Automatic climate control only
99-7335S
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted to match factory dash-”S”=Silver
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
A
C
D E
B
WIRING AND ANTENNA CONNE

Summary of the content on the page No. 2

99-7335S TABLE OF CONTENTS Dash Disassembly - Hyundai Veracruz 2007-2010 (Automatic climate control only) . ... ... .... ... .... ... .. . .1 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 Note: Refer also to the instructions included with the afterm

Summary of the content on the page No. 3

95-7335S DASH DISASSEMBLY HYUNDAI VERACRUZ 2007-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the side trim panels. (Tip: start at the bottom of the panels) (Figure A) 3 Remove (6) Phillips head screws securing the radio trim panel and remove trim panel. (Figure B) 4 Remove (4) Phillips screws securing the climate control, (2) Phillips screws B securing the clock display and (4) Phillips screws securing the pocket from the radio

Summary of the content on the page No. 4

A/C PUSH TEMP FRONT DUAL REAR REAR MANUAL AUTO A OFF MODE PASSENGER TEMP M H R 99-7335S KIT ASSEMBLY KIT PREPARATION 1 Attach the climate control, pocket and the clock display into the 99-7335S radio housing using the factory hardware. (Figure A) Continue to kit assembly. A 2

Summary of the content on the page No. 5

99-7335S KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Snap the pocket into the bottom B opening of the rad

Summary of the content on the page No. 6

99-7335S KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Snap the pocket into the bottom B opening of the radio housing. (

Summary of the content on the page No. 7

99-7335S KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing. (Figure A) 3 Snap the Double DIN brackets to the B inside edge of the Double DIN trim

Summary of the content on the page No. 8

99-7335S INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 09/02/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST99-7335S