Metra Electronics 99-7400 user manual

Summary of the content on the page No. 1

INST 7400
KIT COMPONENTS
6
Shaft
Fig. A Masks
99-7400
Radio
Housing #1
INSTALLATION
INSTRUCTIONS
Radio
Fig. B
Housing #2
Faceplate #1
APPLICATIONS
CAR PAGE
Faceplate #2
IF AN EQUALIZER WILL BE INCLUDED: Slide the aftermarket equalizer into the back of the
NISSAN
kit. Using the hardware included with the equalizer, mount the unit to the kit. (see Fig. A)
200SX 1980-83.............................................................................1
Brac

Summary of the content on the page No. 2

NISSAN 200SX 1980-83 ALL VEHICLES 1 2 4 Fig. C Fig. A Fig. D Disconnect the negative battery terminal to prevent an accidental short circuit. Remove Fig. B (4) Phillips screws above the radio opening. Remove (1) Phillips screw below the left side of Using the scored lines as a guide, cut and the radio opening. Remove (1) Phillips screw remove the dashed portions of Faceplate #2. from each side of the dash trim bezel. Pull off MAXIMA 1987-91, PULSAR 1987-90, STANZA 1987-89, 240SX: Moun

Summary of the content on the page No. 3

NISSAN Stanza 1987-89 NISSAN 200SX 1984-88 1 2 1 2 Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Remove prevent an accidental short circuit. Remove the ashtray and (2) screws exposed at the (1) #10 Phillips screw from each side of the base of the dash trim bezel. Remove (2) Using the scored lines as a guide, cut and center console. Unsnap the coin tray and Locate Faceplate #2. (It is NOT necessary screws

Summary of the content on the page No. 4

NISSAN 240SX 1989-94 NISSAN Stanza 1982-86 1 2 1 2 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (3) screws from the top of the dash trim bezel. Remove (1) screw from each side of Disconnect the negative battery terminal to Using the scored lines as a guide, cut and Using the scored lines as a guide, cut and the ashtray housing. Remove (3) screws prevent an accidental short circuit. Unclip remove the dashed portions of Faceplate remove the da

Summary of the content on the page No. 5

NISSAN Sentra 1987-90 NISSAN Axxess 1989-90 1 2 1 2 Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Remove prevent an accidental short circuit. Remove (2) the ashtray. Remove (2) screws above the screws from the top of the dash trim bezel and climate controls. Remove (2) screws from Locate Faceplate #2. (It is NOT necessary remove the bezel. Remove (4) fasteners from Using the scored lines as a guide, cut th

Summary of the content on the page No. 6

NISSAN Hardbody Pickup / Pathfinder 1986 1/2-93 NISSAN Pulsar 1987-90 1 2 1 2 Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Remove prevent an accidental short circuit. Remove the ashtray and (1) screw exposed in the (3) screws above the climate controls. top-right corner. Remove (2) Phillips screws Using the scored lines as a guide, cut and Remove (2) screws from the bottom edge of Using the scored lines as a

Summary of the content on the page No. 7

NISSAN Pulsar 1983-86 / Sentra 1982-86 NISSAN Maxima 1982-84 1 2 1 2 Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) prevent an accidental short circuit. Remove Phillips screws from the top of the dash trim the knobs from the climate controls. Using a bezel. Remove the ashtray and (1) screw Using the scored lines as a guide, cut small screwdriver, pry out on the climate Using the scored lines as a g

Summary of the content on the page No. 8

NISSAN Maxima 1987-88 NISSAN Maxima 1989-91 1 2 1 2 Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Remove prevent an accidental short circuit. Remove (2) Phillips screws from the bottom of the (2) Phillips screws above the radio opening. dash trim bezel. Remove (2) Phillips screws Using the scored lines as a guide, cut and Remove the ashtray and (1) screw in the Using the scored lines as a guide, cut and abov