Summary of the content on the page No. 1
27” HD Ready LCD TV
DGL2700
User’s Manual
Summary of the content on the page No. 2
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THEIS APPLIANCE TO RAIN OR MOISTURE. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructio
Summary of the content on the page No. 3
10. POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 11. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will
Summary of the content on the page No. 4
Conformity and Compliance FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter
Summary of the content on the page No. 5
WARNING! Important Precautions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT POSSIBLE DANGER, ELECTRIC SHOCK, AND OTHER INJURIES WHEN HANDLING YOUR DISPLAY, PLEASE BE AWARE OF ALL WARNINGS AND SAFETY PRECAUTIONS AS CONTAINED BELOW. WARNING! Never Insert anything into the LCD Display!! Do not insert anything through the openings in the unit, where they can t
Summary of the content on the page No. 6
Important Safety Instructions Read these instructions carefully and save them for future reference. 1. Follow all warnings and instructions marked on the LCD Display. 2. Except as explained elsewhere in this manual, do not attempt to service the LCD Display yourself. Opening or removing covers might expose you to dangerous voltage points or other risks. Refer all servicing of marked components to qualified personnel. 3. Unplug the LCD Display from the wall outlet before cleaning. Do not
Summary of the content on the page No. 7
Table of Contents Introduction.............................................................................................................1 Features................................................................................................................................ 1 Getting Started........................................................................................................1 Unpacking the Package........................................................................
Summary of the content on the page No. 8
Introduction Thank you for purchasing the DIGIMATE DGL2700 display set. This LCD display can be used either as a television or as a computer monitor. With its multiple input options, you can connect almost any device (e.g. VCRs, DVD players and game consoles) to this display. You can also connect your display to a stereo system. Connect a powered subwoofer to experience the ultimate in home entertainment. This manual has been designed to help you install and operate your display properly
Summary of the content on the page No. 9
Location and Function Controls Front View Main Power Switch LED indicator Front Buttons Green: Display is turned on. Red: Standby mode or no signal. # Button Description Press to turn the display on/off after turning On the main 1 POWER power switch located on the lower back panel, next to the AC Cord terminal. 2 SOURCE Press to go through all the available input sources. 3 MENU Press to open the OSD menu of your Display. Press to select an item,
Summary of the content on the page No. 10
Rear View, Side View and Bottom View Use Y1Pb1Pr1 / Y2Pb2Pr2, AV, or S-video to connect the VCR, DVD or the Video Game. ANT Connect the coaxial Connect the cable or antenna power supply Audio cable connects to PC audio. VGA cable connects to VGA card. Side View # Jack Description Video Component1 Input terminal accepts video signal 1 Y1Pb1Pr1 from a Component Video Source (INTERLACED only) Y1Pb1Pr1 2 L&R Audio input corresponding with Video Component1 A
Summary of the content on the page No. 11
# Jack Description To connect the Audio corresponding to AV1 source 11 AV 1 audio in To connect the AV2 Video source. 12 AV 2 in To connect the Audio corresponding to AV2 source 13 AV 2 audio in To connect the Audio Corresponding to AV3 source 14 AV 3 audio in To connect the AV3 Video source. 15 AV 3 in Provides L&R Audio output to connect a set of 16 Headphone headphones. Bottom View # Jack Description Accepts the Audio signal from your PC or Laptop. 1 PC Audio Connect the
Summary of the content on the page No. 12
REMOTE CONTROL BATTERY INSTALLATION Slide the battery compartment cover. Install two “AAA” batteries (not supplied), paying close attention to the + / - polarity diagram in the battery compartment. Replace the compartment cover. BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1 Use only the size and type of batteries specified. 2 Be sure to follow the correct polarity when installing the batteries as indicated in the battery co
Summary of the content on the page No. 13
Using the Remote Control The remote control can be used to control every aspect of the display's operation and provides ease-of-use of the LCD Display: Button Description Power On / Off (standby) after turning on the main power switch. Displays the current information such as channel, etc. Go to the TV menu directly. Cycle through input sources: TV AV1 AV2 AV3 S-Video YPbPr1 YPbPr2 VGA . Also the source key for main source under PIP/PBP mode. Switch source directly to
Summary of the content on the page No. 14
Installation Installing your Display Step 1. Positioning the Display set Place your LCD Display set on a solid and stable surface. To avoid malfunctions, do not expose the LCD Display to water or a heat source and do not obstruct the ventilation grid at the back of the LCD Display. Step 2. Connecting the aerials Use for connecting the 75 Ohm antenna or coaxial cable to the TV Tuner terminal situated on back panel. Antenna or coaxial cable Step 3. Connecting the power cable Plug
Summary of the content on the page No. 15
ANTENNA CONNECTIONS If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV (CATV) see “CABLE TV CONNECTIONS”. Combination VHF/UHF Antenna (Single 75 Ohm cable or 300 Ohm twin-lead wire) Connect the 75 Ohm cable from the combination VHF/UHF antenna to the Antenna Jack. If your combination VHF/UHF antenna has a 300 Ohm twin-lead wire, the use of the 300-75 Ohm Matching Transformer may be necessary.
Summary of the content on the page No. 16
Connecting to different Sources/Devices Video System This display supports various input devices including component, composite and S-Video. To learn how to connect these devices to the display, consult your device's manual. Audio System Connect your display to a stereo system to enhance your viewing experience. To connect the display to an audio system, connect one end of the RCA cables to the input blocks of your stereo system then connect the other end to the audio output blocks of th
Summary of the content on the page No. 17
Channel Skip Programming Use Channel Skip to set which channels you may want to skip when tuning Up or Down using the channel buttons on the remote control. Press MENU then press 3 times to go the TV page of the menu. Press to highlight the third item Channel Skip then press . Use to select the channels you want to skip. Every time you get to a channel you want to skip, press ENTER. A check mark appears beside the channel number that has been marked skipped. Tips: To uns
Summary of the content on the page No. 18
Using the Display Basic Operation Turning the Power On/Off Press POWER to turn on the LCD Display. The power indicator changes from red to green. When the power is off, the power indicator changes from green to red. Selecting the Source Press SOURCE to select the input signal. Each time the SOURCE is pressed, the on-screen display will cycle through the different sources that are supported by the device. There are 8 sources are supported: TV, AV1, AV2, AV3, S-Video, YPbPr1, YPbPr2 and VG
Summary of the content on the page No. 19
Main Menu There are five main items in the OSD Menu. Video Audio Miscellaneous TV PC 1. Video menu (Available for TV and Video modes) 2. Audio menu (Available for TV, Video and PC modes) 3. Miscellaneous menu (Available for TV, Video and PC modes) 4. TV menu 5. PC menu (Available for VGA modes) In TV mode Press MENU on the remote control and the OSD menu will be displayed. Note: In TV mode, PC menu is disabled. In Video mode (AV, S-Video and YPbPr) Press MENU on the remote
Summary of the content on the page No. 20
Audio Menu Audio settings: Bass: Adjust the level of low frequency content in the sound. Treble: Adjust the level of high frequency content in the sound. Balance: Adjust the output of the R/L speakers to obtain the best stereo reproduction. Surround: Enable/disable the surround effect. Equalizer 1/2: Choose from a variety of preset audio equalizer settings. The available settings for equalizer 1 are: Church, Arena, Cave, Bathroom, Hall, Living Room, and Concert. The available
