Summary of the content on the page No. 1
PLASMA TV
OWNER`S MANUAL
MODEL: PH-4210D
Please read this manual carefully and completely before
operating the unit, and retain this manual for future
reference.
Summary of the content on the page No. 2
WARNING RISK ELECTRIC SHOOK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th pr
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1)Save these Instructions ---the safety and operating instructions should be retained for future reference. 2)All warning on the appliance and in the operating instructions should be followed. 3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid cleaners or aerosol clean
Summary of the content on the page No. 4
b.If liquid has been spilled, or objects have been fallen into the unit. c.If the unit has been exposed to rain or water. d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.
Summary of the content on the page No. 5
Warning..............................................................2 Prog. Switch.......................................................19 Safety Instructions............................................ 3-4 Picture Quality adjust Picture Quality Adjust .........................................20 Introduction Sound Adjustment Controls...........................................................6 Sound Adjust......................................................21 Connection
Summary of the content on the page No. 6
Front panel controls EXIT INPUT CH- CH+ VOL- VOL+ MENU Menu enter / exit Power On/Off Button Signal source selection Power Standby Indicator illuminates red in standby mode,illuminates blue when the display is turned on Down/Up. Select desired option on MENU or tune to the desired channel. Remote Control Sensor VOLUME Buttons MENU Button 6 Plasma TV
Summary of the content on the page No. 7
Real panel controls S-Video Input VGA Input/Audio input DVI Input/Audio input connect your cable/PC through the input Power On/Off Earphone port ON OFF VGA IN AV IN COMPONENT IN DVI IN AV OUT R L AC-INPUT AUDIO OUT VGA AUDIO VIDEO S-VIDEO L-AUDIO-R ANT IN Pr/Cr Pb/Cb Y L-AUDIO-R DVI AUDIO VIDEO L-AUDIO-R Audio/Video Input Connect audio/video DVD/DTV Input output from an external Connect a component video/audio devi
Summary of the content on the page No. 8
When using the remote control. Aim it towards the remote sensor on the TV. Function introduction FREEZE INPUT Freezes the currently-viewed picture. Select the source input mode. SLEEP MUTE Switches the sound on or off Press this key to set sleeptimer. PC POWER PC FREEZE INPUT POWER Select PC source Turns your TV or any other programmed equipment on or off, depending on mode. AUTO AUTO SLEEP MUTE DISPLAY Auto adjust for PC display Display of current channel signals, program and systems FAVORITE
Summary of the content on the page No. 9
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. PC VIDEO INPUT POWER AUTO DVI MUTE DISPLAY MENU DNR AVC EXIT ENTER P.STD VOL+ LOCK CALENDAR S.STD VOL- / SAVING CC ARC SURROUND SLEEP FREEZE RATING HDMI to DVI Audio/Video Audio Cord Adaptor Cord ST4X16 (2.5MX2) Screw(x16) Connection cord Speaker unit(X2) Connecting block X4 M4X12Screwsx8 M5X16Screwsx4 Brace pole x2 4 Stand
Summary of the content on the page No. 10
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV Do not leave a still picture from a VCR on the screen for an extended period. If the 4:3 format is used, the fixed images on the sides of the screen may remain visible on the screen if this format is used day after day. This is known as burn-in, and it is an uneven wear of the screen area. Reduce contrast when displaying fixed images on the screen for long periods. 1. Connect the audio and video cables fr
Summary of the content on the page No. 11
How to connect Connect the audio and video cables from the external equipment's output jacks to the TV`s AV IN input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Select the input source by using the INPUT button on the remote control. 2. Operate the corresponding external equipment. Refer to external equipment operating guide. How to connect 1. Connect the DVD video ou
Summary of the content on the page No. 12
- To watch digitally broadcast programs, purchase and connect a digital set-top box. Digital Set-top Box How to connect Use the TV`s COMPONENT (Y, Pb, Pr)IN jacks, VGA or DVI IN port for video connections, depending on your set-top box connections available. Then, make the corresponding audio connections. YPbPr/YCbCr VGA DVI Signal How to use 480i Yes Yes No 1. Turn on the digital set-top box. (Refer to the owner`s manual for the digital Yes 480p Yes Yes set-top box.) 720p Yes Yes Yes 2. Use INP
Summary of the content on the page No. 13
How to connect 1. To get the best picture quality, adjust the PC graphics card as required. 2. Use the TV`s VGA IN or DVI (Digital Visual Interface) IN port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog or digital RGB simultaneously, connect only one of either VGA IN or DVI IN to display the PC on the TV. If the graphic card on the PC does output analog or digital RGB simultaneously, set the display to either VGA or DVI; (the ot
Summary of the content on the page No. 14
Installing the Speakers Íâ¹ÒÑïÉùÆ÷ʹÓÃ˵Ã÷ 1 Face the Plasma screen upside down on a clean blanket and pay attention not to indent the casing. Lay the two speaker aside of the Plasma. 2. Fix 4 ST4X16 screws to the speaker. 3.Lean the speaker against the plasma screen, ensuring that the screw holes on the connecting block are in Line with the screw holes on the plasma screen then hold the speaker in place. 4. Fix the speaker to the plasma screen with ST4X16 screws. 5. Connect the spea
Summary of the content on the page No. 15
Installing the Stand Insert the supporting bracket with 8 M4x12 screws to the installation holes on the bottom of the soleplate. Fasten the Supporting bracket and the Soleplate as shown in figure. Installing the Stand to the Plasma Face the Plasma screen upside down on a clean blanket and pay attention not to indent the casing. Lay down the stand and put it to responding position of the Plasma screen ,and make sure the brace pole is towards the hole of the Plasma. Affix the 2 Plasma brace pol
Summary of the content on the page No. 16
In this manual, the OSD (On Screen Display) may be vary from what is dispayed on your set. What is shown in this manual is an example to help you with the operartion of your set. TV Turning on the TV just after installation. 1. Connect power cord correctly to the television. 2. Press the SWITCH button on back of the TV. The TV is powered up and set in to standby mode. Press the POWER button on the remote control or button on the TV and then the TV will turn on. Turning on the TV 1. If the TV wa
Summary of the content on the page No. 17
Basic Functions Operation Menu 1.Press MENU button to open the main menu. Press VOL+/- button to select the PIC., SOU., ADJ., SYS. , FUN. or TIME menu. 2.Press CH+/- button to select submenu, and press VOL+/- button to increase/decrease the value or select the setup. 3.Press MENU to return to the main menu. 4.The setup time in display will disappear automatically when the latest preset time expiries. MENU display time can be set to 5,10,15,20,25,30 and 40 seconds. 5.Press EXIT button to exit
Summary of the content on the page No. 18
System Menu This TV set has three methods to set channels: Automatic search, manual search, and fine tune. In this section, how to use the remote control to set channels is explained. You can also use the buttons on the TV set to set channel. Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). 1 Press MENU button and then use VOL+/- button to select th
Summary of the content on the page No. 19
System Menu Color Sys. AUTO Fine Tune Sound Sys. M/N If the picture and/or sound are poor, try using the fine tune feature. Fine Tune 49.75MHz Do not use this feature unless reception is poor. Skip Off Channel Type Cable 1 Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item. CATV Type STD Auto Scan 2 Press VOL+/- buttons repeatedly to carry out fine tune, until the best
Summary of the content on the page No. 20
Picture Quality Adjustment Picture Quality Adjustment The TV menu gives you an overview of MENU you can select to adjust picture quality. Note: Depending on the input signal, one or more menu items may not be selectable. 1 Press MENU and then use VOL+/- button to select the PIC. Menu. 2 Press CH+/-button to select the desired items. Mode Custom 3 Press VOL+/- button to adjust the setting. Contrast 50 Brightness 50 4 When you are satisfied with your ch
