Summary of the content on the page No. 1
OWNER'S MANUAL
DieHard,
Battery Charger
12/2 Amp
Fully Automatic
Microprocessor Controlled
Engine Starter
75 Amp
Model No.
200.71223
CAUTION:
Read all Safety Rules and Operating instructions,
and follow them with each use of this product.
Sears_ Roebuck and Co, Hoffman Estates_ IL 60179 U.S.A.
0099000311-602
Summary of the content on the page No. 2
WARRANTY.............................................................................................................. 2 IMPORTANT SAFETY INSTRUCTIONS .................................................................. 3 PERSONAL SAFETY PRECAUTIONS .................................................................... 4 BEFORE USING YOUR BA'n'ERY CHARGER ....................................................... 5 Assembling your charger ................................................................
Summary of the content on the page No. 3
WARNING: To reduce the risk of HELP US HELP YOU-- explosion, explosive gases, or injury Remember: while using your battery charger, follow • Place charger as far away from the the precautions listed below: battery being charged as the charger • Read all instructions and cautions cables will permit. printed on the battery charger, • Do not expose charger to rain or battery, and vehicle or equipment snow. using battery. • Never charge a frozen battery. If • Use charger only on lead-acid type batte
Summary of the content on the page No. 4
For your own personal safety, please follow the following precautions: Remove all personal metal items • Wear complete eye and clothing from your body such as rings, protection when working with lead- acid batteries, bracelets, necklaces and watches, while working with a lead-acid battery. • Be sure that someone is within range A battery can produce a short circuit of your voice to come to your aid if current high enough to weld a ring (or needed while you work with or are the like) to metal, ca
Summary of the content on the page No. 5
It is important to understand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery for charging. ASSEMBLING YOUR CHARGER Included with your battery charger are two cord wrap cleats for storage of the clamp cables. To install, align the three tabs to corre- spond with the three receptacles and push until you hear a snap. Wrap clamp cord after unplugging the [_ ('-Cord Wrap Cleat power cord and store your charger in a dry
Summary of the content on the page No. 6
It is important that you read and follow these guidelines while you are preparing to charge your battery. vent caps while charging, and • Make sure that you have a 6 volt or recommended rates of charge. 12 volt lead-acid battery. • Wear safety glasses. See additional • Clean the battery terminals. Be "Personal Safety Precautions" on careful to keep corrosion from getting page 4. in or around your eyes. • Be sure that the area around the • For batteries with removable vent battery is well ventila
Summary of the content on the page No. 7
For best results from your battery charger, learn to use it properly. This section tells how to set the controls and how to charge a battery in and out of a vehicle. TOUCH PAD / L _ _ LEDs CONTROL _ BATTERY TYPE BUTTONS _ _ _ _ 12VOLT _-V_] r nVnlT'_ TYPE1 l TYPE2 J L ..... J BATTERY STATUS r-] I--I I--I I--I r--I I--]_ CHECK CHARGED 2 Amp charge rate: Intended for Indication of this special mode is the charging of small batteries such as flashing of the first amber LED in the those commonly use
Summary of the content on the page No. 8
The next four LED's are amber. First, NOTE: The charger defaults to Type 1 when first plugged in or when discon- only the leftmost amber LED will light. nected from a battery. The 6 VOLT Then two, then three, and eventually all button must then be pressed before four amber LED's will light. Refer to "Estimating Charge Time" on page 12 charging a 6 volt battery. for more information. With the exception of AGM and gel cell The sixth LED is green and lights to indi- batteries, all other battery typ
Summary of the content on the page No. 9
MODEL 71223 E] I--I r--I _l '_ iE_-mmr STATUS X indicates panel lights that continuously glow. EAMP 12M,IF _lZ'It 12¥DLT IZ¥0LI" 8VnL1r i I"-3 r--I D [Z] r-'1 r--I °"°"° i ;"°: B indicates panel lights that blink on and off. J 6 & 12V. 6 i 12V. I"VPE1 'rYlPE 2 i CHECK -- €ItAEGI_I) X X X Initial power up X user selected user selected Battery REVERSED or NOT connected user selected user selected X Normal battery detected, charge started user selected user selected B Sulfated battery detected, cha
Summary of the content on the page No. 10
is made. Then connect the black IMPORTANT: Follow all safety instruc- tions and precautions when charging (NEGATIVE) output clamp to a your battery. Wear complete eye heavy, unpainted metal part of the protection and clothing protection. chassis or engine block, away from Charge your battery in a well-ventilated the battery (see figure above). DO area. NOT connect clamp to negative battery post, carburetor, fuel line or Charging your battery in the vehicle: sheet metal part. 1. Avoid personal in
Summary of the content on the page No. 11
. To disconnect the charger, unplug Charging your battery removed from the vehicle: the charger power cord before attempting to disconnect the charger clamps. Then, standing away from POSITIVE NEGATIVE the battery, remove the output clamp from the NEGATIVE battery post. Finally, remove the output clamp from the POSITIVE battery post. . Clean and store the charger in a dry II 24", 6 GAUGE II \ location, U U\ GROUNOEO USING ENGINE START POWER OILrFLET Your battery charger can be used to jump start
Summary of the content on the page No. 12
This charger adjusts the charging time in order to charge the battery completely, efficiently, and safely. The microprocessor automatically makes all necessary calculations. However, this section includes guidelines that can be used to estimate charging time. The duration of the charging process de- charger allows. However, some pends on each of three factors. smaller batteries, such as motor- cycle and tractor batteries, have a 1. Battery state: A battery that has only maximum recommended charg
Summary of the content on the page No. 13
A minimal amount of care can keep your battery charger working properly for years. 3. Occasional cleaning of the case of 1. Clean the clamps each time you are the charger with a soft cloth will keep finished charging. Wipe off any battery the finish shiny and help prevent fluid that may have come in contact corrosion. with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger. This will help prevent accidental damage to the cords and charger. 13
Summary of the content on the page No. 14
Performanceproblemsoften resultfrom littlethings that you canfix yourself.Please read throughthis chartfor a possiblesolutionif a problemoccurs. PROBLEM POSSIBLE CAUSE SOLUTION Indicator lights are lit in The charger may be Return to place an erratic manner not defective, of purchase for a explained in the "Using replacement. Your Battery Charger" section. The red abort light always This will happen if the Reset the charger by flashes before the battery battery did not reach full unplugging it o
Summary of the content on the page No. 15
This section shows an illustration of your battery charger. Use it to become familiar with part locations and appearance. Item Description Part Number Item Description Part Number 1. Transformer 93026558 7. ACPowerCord 90026135 2. SCRControlModule 2299001160 8. Handle 3599000270 3. Screw 8-18 xY2"(4) 5199000274 9. Faceplate 0899001725 4. Touch Pad Control Board 2299001208 10. CordCleat 1199004390 5. Circuit Breaker 3999000105 Owner's Manual 0099000311 6. OutputCables 3899002000 15
Summary of the content on the page No. 16
For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm CT Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). 16
