Summary of the content on the page No. 1
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 12
VEC1089ABD
FIVE YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Manufacturing, regarding this product. There is no other warranty, other than those
described herein.
This Vector Manufacturing product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for five years from the date of purchase
Summary of the content on the page No. 2
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page ii Figure IMPORTANT SAFETY INSTRUCTIONS Figure ADAPTER (B) 1A 1B WARNINGS 1. RISK OF EXPLOSIVE GAS MIXTURES — WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE GROUNDING THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND GROUNDING MEANS FOLLOW THE INSTRUCTIONS EXACTLY. PIN (A) 2. To reduce risk of battery explosion,
Summary of the content on the page No. 3
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page iv 5. For negative-grounded vehicle, connect POSITIVE (RED) clamp from battery charger to POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK) clamp to vehicle chassis or TABLE OF CONTENTS engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to heavy gauge metal part of the frame or engine block. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 2 internal chemical energy transfer. At the end of Stage 2, the charger will automatically Battery Voltage — enables a check that measures the battery voltage and displays move into Stage 3 charge mode. it for 3 seconds. Stage Three — Top-Off Charge — voltage is automatically maintained and Battery Recond — improves performance of sulfated and aged batteries. reduced to a predetermined level while current is adjusted for a safe, effective battery A
Summary of the content on the page No. 5
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 4 OPERATING INSTRUCTIONS 4. Pressing the 2/10/15 AMP button repeatedly advances to standby mode; the unit sounds a beep, displays “000” and stops charging. The battery charger Ensure that all installation and operating instructions and safety displays the charge current. To view the battery voltage, press BATTERY VOLTAGE precautions are understood and carefully followed by anyone button. The charger will sound a beep and display the battery voltag
Summary of the content on the page No. 6
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 6 Alternator Check 6. Fill the battery with distilled water according to the manufacturer’s instructions. Since batteries may rapidly bubble while being charged, remember to refill (only Part 1 with distilled water) after the equalization process is complete and the voltage is No Load (Turn OFF all vehicle’s accessories): The battery must be fully charged back to normal. before testing the alternator. Run the engine long enough to achieve 7. Follow
Summary of the content on the page No. 7
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 8 The times shown in the table on page 7 are approximate and refer to a 50 Ah TROUBLESHOOTING automotive battery. For example, a 50 Ah (12 volt) battery is discharged (50%). How long should it be charged at the 15 amp rate? See the chart above under “50%” and Display Indications/Common Problems/Possible Solutions “at 15 amp rate.” In most cases, battery charging times will vary depending on the size, age and No Functions condition of the battery.
Summary of the content on the page No. 8
VEC1089ABD_Manual_042805 5/9/05 2:40 PM Page 10 10 11
