Summary of the content on the page No. 1
PROFESSIONAL
SERIES
CA 5150
Owner’s Guide
Remote Start and Keyless
Entry System
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2010 Audiovox Electronics Corporation. All rights reserved. 1
Summary of the content on the page No. 2
Table of Contents Using Your Remote Control ............................................................... 3 Using the Keyless Entry ................................................................... 3 Two Stage Door Unlock (optional) ................................................... 3 Activating Trunk Release (optional) ................................................ 3 Using the Progressive Car Finder Feature ...................................... 3 Using the Personal Protection Alarm ....
Summary of the content on the page No. 3
Using Your Remote Control Using the Keyless Entry The button is used to lock the vehicle's doors, the button is used to unlock the vehicle's doors. To lock or unlock the doors simply press and release the desired function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked. NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the or button to activate an audible locking
Summary of the content on the page No. 4
Programmed Transmitter Notification As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance. Valet Mode Valet Mode is used to disable the system from remote starting. To enter or exit valet mode
Summary of the content on the page No. 5
Entering the Vehicle while it is Running via Remote Vehicle Start 1. Unlock the vehicle’s doors. 2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! 3. Insert the key into the ignition switch and turn to the ON or RUN position. 4. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally. Preheating or Precooling the Vehicle’s interior Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the syste
Summary of the content on the page No. 6
Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, selection between 2 or 3 hour is made in option programming. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine prod
Summary of the content on the page No. 7
Remote Start Safety Features For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur: 1. The vehicle hood is open. 2. The brake pedal is pressed prior to turning the ignition key to the ON position. 3. The engine is over-reved (tach checking only). 4. Valet mode is active. Transmitter Button Functions 1 Way Car Find / Lock Unlock Start Operation Method Transmitter Panic Lock X Press and Release Unlock X Pres
Summary of the content on the page No. 8
Replacing Remote Control Batteries 1-Way Remote Control: The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 3 screws and disassemble the halves of the remote control. 2. Remove the old batterie
Summary of the content on the page No. 9
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this Product under normal use and conditions, be proven defective in material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI- NALLY INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts d
Summary of the content on the page No. 10
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for
