Summary of the content on the page No. 1
BDL4681XU
www.philips.com/welcome
EN User manual
Cleaning and troubleshooting
Summary of the content on the page No. 2
User Manual BDL4681XU SAFETY AND TROUBLESHOOTING INFORMATION Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your monitor: Operation: • Keep the monitor out of direct sunlight and away from stoves or any other heat source. • Remove any object that could fall into ventil
Summary of the content on the page No. 3
User Manual BDL4681XU Service: • The casing cover should be opened only by qualified service personnel. • If there is any need for any document for repair or integration, please contact with your local service center. • Do not leave your monitor in a car/trunk under direct sun light. Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed. Read and follow these instr
Summary of the content on the page No. 4
User Manual BDL4681XU REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declares under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • E
Summary of the content on the page No. 5
User Manual BDL4681XU POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely s
Summary of the content on the page No. 6
User Manual BDL4681XU INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains
Summary of the content on the page No. 7
User Manual BDL4681XU ( RoHS + (Hg) (Cd) (PBB) (PBDE) (Pb) (Cr 6 ) OOO O O O XX O O O O XO O O O O XO O O O O ( ) XO O O O O O SJ/T11363-2006 X SJ/T11363-2006 ( )
Summary of the content on the page No. 8
User Manual BDL4681XU NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ
Summary of the content on the page No. 9
User Manual BDL4681XU TABLE OF CONTENTS 1. UNPACKING AND INSTALLATION 1.1. UNPACKING 1.2. PACKAGE CONTENTS 1.3. INSTALLATION NOTES 1.4. PORTRAIT MOUNTING 2. PARTS AND FUNCTIONS 2.1. REAR VIEW 2.2. INPUT/OUTPUT TERMINALS 2.3. REMOTE CONTROL 2.3.1. GENERAL FUNCTIONS 2.3.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 2.3.3. OPERATING RANGE OF THE REMOTE CONTROL 3. CONNECTIONS TO EXTERNAL EQUIPMENT 3.1. USING THE C
Summary of the content on the page No. 10
User Manual BDL4681XU 6.3. BRIGHT DOT DEFECTS 6.4. DARK DOT DEFECTS 6.5. PROXIMITY OF PIXEL DEFECTS 6.6. PIXEL DEFECT TOLERANCES 7. CLEANING AND TROUBLESHOOTING 7.1. CLEANING 7.2. TROUBLESHOOTING 8. TECHNICAL SPECIFICATIONS
Summary of the content on the page No. 11
User Manual BDL4681XU 1. UNPACKING AND INSTALLATION 1.1. UNPACKING • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • The weight of the product differs - depending on the type. Due to the size and weight it is recommended to move it by 2 people. • The protective glass and the glass substrate are installed on the front of the product. Since both glass can be broken and scraped easily, the product has
Summary of the content on the page No. 12
User Manual BDL4681XU 1.4. PORTRAIT MOUNTING Wall mounting holes Notes: Note: The "AC IN" socket should be located at the bottom of all connector terminals when rotating your monitor. • Metric 6 (10mm) screws (having a length 10-15mm longer than the thickness of the mounting bracket) are needed for wall mounting (not included). Tighten the screws securely (recommended torque: 470 - 635N•cm) • The mounting interface should comply with the UL1678 standard in North America. The mounting mea
Summary of the content on the page No. 13
User Manual BDL4681XU 2. PARTS AND FUNCTIONS 2.1. REAR VIEW 8 7 Dent depth: 6mm 9 10 8 9 1 2 3 4 5 6 1. ENTER/VIDEO SOURCE button • Use this button to select the input source. • When the On Screen Display menu is active, use this as the SET button. 2. MENU button • Use this button to engage the On Screen Display menu. • When the On Screen Display menu is active, use this button to return to the previous menu. 3. / button • When the On Screen Display menu is active, use these as the UP/D
Summary of the content on the page No. 14
User Manual BDL4681XU 8. Carrying handle Use these handles when carrying the monitor by hand. 9. Cable retainer installation holes Install the cable retainer using these holes. 10. Remote control sensor, ambient light sensor and power indicator • Receives command signals from the remote control. • Detects the ambient lighting condition around the monitor. • Indicates the operating status of the monitor: - lights blue when the monitor is turned on - lights amber when the monitor is in standby mod
Summary of the content on the page No. 15
User Manual BDL4681XU 2.2. INPUT/OUTPUT TERMINALS 9 14 13 1 2 3 4 5 6 7 8 10 11 12 15 1. AC IN (5.5 A) 9. VGA OUT Connect the supplied power cord to the wall outlet. Outputs the VGA signal from the VGA IN jack. 2. Main power switch 10. VGA IN Press to switch the main power on/off. Connect to the VGA output of a computer. 3. AUDIO IN (AUDIO1) 11. RS232C (OUT/IN) Connect to the audio output of a computer. RS232C network connection input/output for the use of loop through function. 4. AUDIO OUT
Summary of the content on the page No. 16
User Manual BDL4681XU 2.3. REMOTE CONTROL 2.3.1. GENERAL FUNCTIONS POWER button Press to switch on the monitor from standby mode. Press again to turn it off to standby mode. SMART button To select smart picture mode from: • HIGHBRIGHT: for moving image such as Video • STANDARD: for images (factory setting) • sRGB: for text based images • CINEMA: for movies. • CUSTOM: use your own picture setting. The mode is automatically selected after you change the settings in the PICTURE menu. VIDEO
Summary of the content on the page No. 17
User Manual BDL4681XU DISPLAY button To turn on/off the setting information displayed on the upper right corner of the screen. MENU button To turn the OSD menu on/off. UP button • To move the highlight bar up to adjust the selected item when OSD menu is on. • To move the sub-picture up in “PIP” mode. DOWN button • To move the highlight bar down to adjust the selected item when OSD menu is on. • To move the sub-picture down in “PIP” mode. PLUS button • To increase the adjustment with OSD menu.
Summary of the content on the page No. 18
User Manual BDL4681XU 2.3.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL 1. Remove the cover on the rear of the remote control. 2. Insert two AAA size 1.5V batteries ensuring that the “+” and “-” ends of the batteries are correctly aligned. 3. Replace the cover. Note: Do not mix battery types, e.g. alkaline and manganese. 2.3.3. OPERATING RANGE OF THE REMOTE CONTROL When pressing a remote control button, point the top of the remote control toward the remote control sensor from the rea
Summary of the content on the page No. 19
User Manual BDL4681XU 3. CONNECTIONS TO EXTERNAL EQUIPMENT 3.1. USING THE CABLE RETAINER 3.2. USING THE SWITCH COVER You can use the switch cover to prevent the monitor from being turned on or off accidentally. 3.3. CONNECTING EXTERNAL EQUIPMENT (DVD/VCR/VCD) 3.3.1. USING COMPONENT VIDEO INPUT 1. Connect the green-colored (labeled as "Y") jack of the device to the green-colored "Y" jack of the monitor. 2. Connect the blue-colored (labeled as "Pb") jack of the device to the blue-co
Summary of the content on the page No. 20
User Manual BDL4681XU 3.3.2. USING S-VIDEO INPUT 1. Connect the S-Video connector of the external device to the S-VIDEO input of the monitor. 2. Connect the red (R) and white (L) audio jacks of the device to the AUDIO IN (AUDIO2 or AUDIO3) jacks of the monitor. DVD/VCR/VCD 3.3.3. USING VIDEO INPUT 1. Connect the Video connector of the external device to the VIDEO IN input of the monitor. Use the supplied BNC-to- RCA adapter if necessary. 2. Connect the red (R) and white (L) audio jacks of
