Summary of the content on the page No. 1
Owner’s Manual
Model 9310
Vehicular Slide Gate Operator
DoorKing, Inc.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
www.doorking.com
P/N 9310-065 Rev D 5/05
Copyright 2003 DoorKing, Inc. All rights reserved.
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Use this manual with the following models only. All 9310 models with circuit board 4403-010. IMPORTANT! The 4403 circuit board used in the model 9310 IS NOT interchangeable with the 4402 circuit board used in the earlier model 9300 operators. NOTE: Models 9310-081, 9310-083, 9310-085, 9310-087, 9310-089, 9310-091, 9310-093, 9310- 095 and 9310-097 will have a supplemental manual (P/N 2340-065) that describes the operation and setup of the optional battery backup system available with
Summary of the content on the page No. 4
QUICK START Mount operator to pad using 3/8 or 1/2 sleeve anchors. See page 14-15. 1 Attach chain. Adjust chain to allow approximately 1-inch of sag per 10-feet of gate width. Be sure to remove the pin from the breather plug. 2 See page 16-17. Connect supply voltage as described in section 2.2. Be sure power is OFF! See page 22. 3 Connect control wiring as shown. Radio receiver connects to terminals 1-2-3. Full open input devices connect to terminals 4 and 13. Partial open input devices con
Summary of the content on the page No. 5
CAUTION 16-20 HIGH VOLTAGE! REVERSING DEVICE CONNECTOR 1 2 3 4 5 6 7 8 1 2 3 4 CAPACITOR CONNECTOR GATE FORCED EARTH GROUND PARTIAL 12 3 LIMIT LIMIT 1 Open Cycle Photocell TIMER 2 Close Cycle Photocell ON Secondary 3 Open Cycle Contact Sensor 1 DIRECTION Entrapment Protection 2 TIMER 4 Close Cycle Contact Sensor Devices 5 Common 6 Common 4-Wire 3-Wire Receiver 1 Receiver LIMIT SWITCH 9406 CONNECTOR 1 24V Com -- 2 EXIT 24V Com 1 Relay LOOP Relay 2 Relay 3 Radio Pwr 3 Radio Pwr + ON 4 5 PO
Summary of the content on the page No. 6
TABLE OF CONTENTS Important Notices......................................................................................................................................................8 Important Safety Instructions....................................................................................................................................9 Restrictions and Warnings........................................................................................................................
Summary of the content on the page No. 7
Section 4 – Operating Instructions 4.1 Power and Reset Switches ......................................................................................................................39 4.2 Shutdown Conditions...............................................................................................................................40 Soft Shutdown ..........................................................................................................................................40 Res
Summary of the content on the page No. 8
IMPORTANT NOTICES Vehicular gate systems provide convenience to their users and limit vehicular traffic onto your property. These systems can produce high levels of force; therefore it is important that you are aware of possible hazards associated with your gate operating system. These hazards may include pinch points, entrapment, absence of controlled pedestrian access or traffic backup. Be sure that the installer has instructed you on the proper operation of the gate and gate operato
Summary of the content on the page No. 9
IMPORTANT SAFETY INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate controls. Keep the remote control away from children. 3. Always keep people and objects away from gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE. 4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or stop or reverse when an object activates the non-contact sensors. After adjusting th
Summary of the content on the page No. 10
RESTRICTIONS AND WARNINGS Install The Gate Operator Only If: • The operator is appropriate for the usage Class of the application and the gate is within the weight and length limitations specified for the operator. • All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet (1.2 m) above the ground to prevent a 2 ¼ inch (57.15 mm) diameter sphere from passing through the openings anywhere in the gate, and in that portion of the ad
Summary of the content on the page No. 11
ENTRAPMENT PREVENTION This vehicular gate operator is equipped with an inherent (Type A) entrapment sensing system. This system will sense an obstruction in both the opening and closing gate cycles, and will cause the gate to reverse direction should an obstruction be encountered. If the system detects a second obstruction before reaching the full open or close limit after the initial reversal, an alarm will activate and the operator will require a reset before resuming normal operation
Summary of the content on the page No. 12
GLOSSARY GATE – A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage barrier or is that portion of a wall or fence system that controls entrance and/or egress by persons or vehicles and completes the perimeter of a defined area. RESIDENTIAL VEHICULAR GATE OPERATOR-CLASS I - A vehicular gate operator (or system) intended for use in a home of one-to four single family dwelling, or garage or parking area associated therewith.
Summary of the content on the page No. 13
11 27.5 SECTION 1 - INSTALLATION Prior to beginning the installation of the slide gate operator, we suggest that you become familiar with the instructions, illustrations, and wiring guide-lines in this manual. This will help insure that your installation is performed in an efficient and professional manner. The proper installation of the vehicular slide gate operator is an extremely important and integral part of the overall access control system. Check all local building ordinances a
Summary of the content on the page No. 14
18.5 3 3/4 Min 5 6.5 14 4 1 GATE BRKT 6 1.2 Concrete Pad The model 9310 vehicular gate operator is designed to be mounted on a concrete pad. 1. Construct a form for the mounting pad according to the specifications shown below. Note that the pad for the 1 HP operator extends an additional 6 inches to the right to accommodate the larger cover. Be sure to level the top edge of the form and that the top of the form is a minimum of four (4) inches above ground level. We suggest that you c
Summary of the content on the page No. 15
1.3 Operator Installation • Position the operator on the pad so that there is a minimum clearance of one (1) inch between the back of the operator housing and the gate. • IMPORTANT!! Be sure that the operator 90° is parallel to the gate! Installing the operator in any other manner will cause excessive chain noise, chain wear and stretching, and premature idler failure. • Mark the mounting holes on the mounting pad. Use a concrete drill bit to drill the mounting holes to the size
Summary of the content on the page No. 16
1.4 Chain Installation 1. Secure the chain brackets to each end of the gate so that the brackets are level with the top chain cutouts in the operator housing. Brackets should be attached to the inside of the frame so that the chain bolts, when attached, do not protrude beyond the frame of the gate. 2. Remove the breather plug pin from the gear-box and discard it (page 17). 3. Route the chain through the gate operator: under the chain guide idlers and over the drive sprocket. 4. At
Summary of the content on the page No. 17
8 4 1.5 Front Mount Installation REMOVE BREATHER PLUG PIN CONCRETE PAD GROUND LEVEL 17
Summary of the content on the page No. 18
8 4 1.6 Rear Mount REMOVE BREATHER PLUG PIN CONCRETE PAD GROUND LEVEL Gate Brackets Idler Assembly P/N 2600-818 18
Summary of the content on the page No. 19
1.7 Warning Sign Installation This DoorKing slide gate operator is shipped with two warning signs. The purpose of the warning signs is to alert uninformed persons, and to remind persons familiar with the system, that a potential hazard may exist so that appropriate action can be taken to avoid the hazard or to reduce exposure to the hazard. 1. Permanently install the supplied warning signs in locations WARNING so that the signs are visible by persons on both sides of the gate. 2. Use a
Summary of the content on the page No. 20
20
