Summary of the content on the page No. 1
MODEL G5955
HEAVY DUTY
HANGING AIR FILTER
OWNER'S MANUAL
(For models manufactured since 9/11)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Summary of the content on the page No. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Summary of the content on the page No. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 4: OPERATIONS ........................... 16 SECTION 5: MAINTENANCE ......................... 17 SECTION 6: SERVICE ................................... 18 SECTION 1: SAFETY ....................................... 5 SECTION 7: WIRING ...................................... 19 SECTION 2: POWER SUPPLY ........................ 8 SECT
Summary of the content on the page No. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Summary of the content on the page No. 5
Identification Front View Rear View Figure 1. To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations. Accessories Some aftermarket accessories can be G6514—5-Micron Washable Primary Filter installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this G6513—1-Micron Washable Secondary Filter risk, only install acc
Summary of the content on the page No. 6
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
Weight................................................................................................................................................................ 48 lbs. Width (side-to-side) x Depth (front-to-back) x Height........................................................... 30-5/16 x 24 x 12-3/16 in. Footprint (Le
Summary of the content on the page No. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Summary of the content on the page No. 8
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
Summary of the content on the page No. 9
Additional Safety for Air Filters INTENDED USE. DISCONNECTING POWER SUPPLY. OFF REGULAR CLEANING. HAZARDOUS DUST. LEAD PAINT DUST AND ASBESTOS FIBERS. SUSPENDED DUST PARTICLES AND IGNITION SOURCES. DUST ALLERGIES. FIRE SUPPRESSION
Summary of the content on the page No. 10
SECTION 2: POWER SUPPLY Availability Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual. Circuit Requirements Nominal Voltage ........................................120V Cycle ..........................................................60 Hz Electrocution, fire, or Phase ........................................... Single-Phase equipment d
Summary of the content on the page No. 11
Grounding & Plug Requirements GROUNDED 5-15 RECEPTACLE Extension Cords 5-15 PLUG Figure 2. Minimum Gauge Size ...........................16 AWG Maximum Length (Shorter is Bette
Summary of the content on the page No. 12
SECTION 3: SETUP Needed for Setup Inventory Description Qty Box 1: (Figure 3) Qty A. B. Unpacking please call us immediately at (570) 546-9663 for advice. Otherwise, filing a freight claim can be difficult. Figure 3. NOTICE If you cannot find an item on this list, care- SUFFOCATION HAZA
Summary of the content on the page No. 13
Power Connection Test Run Connecting Power 1. OFF Troubleshooting Page 18 2. To test run the machine: 1. Note: If you installed the Model G5956 remote control, do NOT use the remote con- trol during this procedure. 2. Figure 4. Connecting power. 3. Disconnecting Power 1. OFF 4. ON 2. 5
Summary of the content on the page No. 14
Figure 7 Site Planning Figure 6 Figure 7. Below is a list of things to keep in mind when selecting a spot for the air filter: Figure 6.
Summary of the content on the page No. 15
It is very important that the hanging air filter Mounting Brackets be supported properly Components and Hardware Needed Qty Tools Needed To attach the mounting brackets: 1. Figure 8 Figure 8. The hanging air filter may fall and cause serious inju
Summary of the content on the page No. 16
Mounting Figure 9 10. ONLY mount the air filter unit to joists, wall studs, or table that can hold at least 100 lbs. DO NOT mount the unit only to sheet rock, pressboard, paneling, or honeycomb wall panels with expansion-type fasteners. The fasteners can tear out and the air filter can fall. Ignoring this caution can result in injury or property damage. Figure 9 Components and Hardware Needed Qty Tools Needed Qty
Summary of the content on the page No. 17
To mount the air filter to a ceiling: 4. Figure 9 or 10 1. Tip: Try to keep the hole placement even on the cleats so that the weight of the hanging 2. air cleaner is evenly distributed. 5. 3. Note: The 2X4’s are cut a little longer than the air filter/joists to guard against splitting 6. the ends when fasteners are driven through them.
Summary of the content on the page No. 18
SECTION 4: OPERATIONS Filtering To reduce the risk of Performance serious injury when using this machine, read and understand this entire manual before operating. Damage to your eyes and lungs could result from using this machine without proper pro- tective gear. Always wear safety glasses and a respirator when operating this machine. To calculate the recirculating rate for your shop space: Step 1. THIS AIR FIL
Summary of the content on the page No. 19
SECTION 5: MAINTENANCE Cleaning Filters Figure 11. Keep the air filter unit DO NOT use compressed air to blow out unplugged during all the secondary filter in the following steps. maintenance procedures. If you do, you will damage the filter and Ignoring this warning may reduce filtering quality. result in serious personal injury to you or others! 3 Always wear a respirator 4. and safety glasses
Summary of the content on the page No. 20
SECTION 6: SERVICE Note: Please gather the serial number and manufacture date of your machine before calling. Troubleshooting Motor & Electrical Air Filter Operations
