Summary of the content on the page No. 1
MCC400A/W, C/ER400A/W,
C/ET400A/W, ED400A/W, MFE400A/W
- 220V 60Hz/230V 50Hz Icemakers
Order parts online
Installation, Operation and Service Manual
www.follettice.com
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com 230V 50Hz 00124453R04
models only
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Table of contents Welcome to Follett Corporation 4 Specifications 5 Installation 7 Top mount 7 Satellite-fill 9 Ventilation 14 Ice transport tube 15 Start up 17 Operation 17 Cleaning 17 Weekly exterior care 17 Monthly condenser cleaning 18 Semi-annual evaporator cleaning 18 Service 19 Icemaker operation 19 Technical specifications 20 Refrigeration system diagram 20 T400A/W wiring diagram 20 Refrigeration pressure data 21 Compressor data 21 Gearmotor data 21 Electrical cont
Summary of the content on the page No. 4
Welcome to Follett Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you review the installation portion of this manual before beginning to install the unit. Our instructions are designed to help you achieve a trouble-free installation. Should you have any questions or require technical help at any time, please call our tec
Summary of the content on the page No. 5
Specifications Electrical MCC and C series – 220V 60Hz 5.0 full load amps E series – 230V 50Hz 5.0 full load amps Power cord provided on icemaker and dispenser. Electrical connections Model Electrical connection Circuits required C25FB400A/W, C50FB400A/W cord provided 220V 60Hz E25FB400A/W, E50FB400A/W 230V 50Hz C25CT400A/W, C50CT400A/W cord provided 220V 60Hz E25CT400A/W, E50CT400A/W 230V 50Hz C25CR400A/W, C50CR400A/W cord provided 220V 60Hz, (2) circuits required E25CR400A/W, E50CR400A/W 2
Summary of the content on the page No. 6
Dimensions and clearances Entire front of icemaker must be clear of obstructions/connections to allow removal. 305mm (12") clearance above icemaker for service. Top back view — air-cooled 153mm (6") minimum clearance between exhaust top mount side of icemaker and any adjacent equipment. MCC400A & C/ER400A – 457mm (18") minimum, 3m (10 ft) maximum clearance between discharge C 331mm and air intake grilles. (13.00") 124mm B (4.875") 61mm A (2.375") Front view — air-cooled Side view — air-cool
Summary of the content on the page No. 7
Installation Icemaker performance is very sensitive to the quality of installation. To ensure proper performance, ease of service and warranty coverage, it is critical that you follow the requirements detailed in this manual. If you cannot meet these requirements or have questions, call our technical service group immediately at (800) 523-9361 or (610) 252-7301. Top mount icemaker installation procedure Install icemaker and rough-in utilities 1. Install ice storage bin in its final location.
Summary of the content on the page No. 8
Before turning power on 1. Clean and sanitize ice storage bin in accordance with cleaning procedure in ice storage bin installation information packed with ice storage bin. 2. Turn water to icemaker on. 3. Remove cover on float reservoir. 4. Push down on float to force water out overflow tube and into evaporator drain pan. 5. Check that water drains freely from evaporator drain pan. 6. Lift float and check that float valve shuts off incoming water when raised. After turning power on 1. T
Summary of the content on the page No. 9
Satellite-fill icemaker installation procedure Install icemaker and rough-in utilities without optional slide-out accessory The requirements below are for icemaker installation without the Follett slide-out accessory. These procedures ensure that the icemaker can be easily removed as one unit for cleaning and maintenance. For installation with the slide-out accessory, refer to instructions to install icemaker and rough-in utilities with optional slide-out accessory. General requirements Front
Summary of the content on the page No. 10
Field wiring diagrams Field wiring diagram is intended only to aid electrician or technician in understanding how equipment works. Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord and plug(s) and follow the appropriate field wiring diagram. MCC400A/W and C/ER400A/W icemakers have separate power supply from dispenser Electric disconnects required within 3m (10 ft) for all hard-wired connections Recommended junction box preparation of hard-wired Satell
Summary of the content on the page No. 11
Install icemaker and rough-in utilities with optional slide-out accessory The slide-out accessory allows the icemaker to be pulled out on a track from below a counter without disconnecting utilities. A leg supports the icemaker in the full-out position. If your order did not include a slide-out accessory proceed to icemaker ventilation and exhaust. Step 1 – Installing track accessory (Follow either A or B below) Track must be positioned flush against inside of counter and slightly above count
Summary of the content on the page No. 12
Step 2 – Installing icemaker on slide-out track A. When icemaker is shipped with slide-out track accessory (follow either A or B) 1. Connect inlet water, drain, and power supply to back of vertical utility panel. 2. Place icemaker on slide-out track assembly. 3. Connect drain and water lines. 4. Connect electrical cords from icemaker to appropriate plug and connect to power supply. B. When icemaker is installed in and shipped with counter 1. Remove two outer rear screws from icemaker and i
Summary of the content on the page No. 13
134mm Front view 3/8" OD push-in condenser inlet (5.25") (water-cooled only) 3/8" OD push-in condenser drain (water-cooled only) icemaker 3/8" OD push-in icemaker water inlet twist-lock bin signal cord barbed push-on icemaker drain 658mm (25.875") Side view (All customer field connections are made 3/8" OD push-in condenser inlet to rear of vertical cord holder (water-cooled only) utility panel) 3/8" OD push-in condenser drain vertical utility panel (water-cooled only) 3/8" OD push-in icemake
Summary of the content on the page No. 14
Satellite-fill icemaker ventilation and exhaust requirements Fabricator-supplied, custom air intake grilles must have 305mm x 305mm (12" x 12") opening yielding 645 sq. cm (100 sq. inches) of open air space within duct perimeter. Block off any open area outside of the air duct. Intake air requirements — air-cooled icemakers (MCC400A & C/ER400A only) 1. Check that 51mm (2") duct is installed on condenser front. 2. Cut a 305mm x 305mm (12" x 12") opening in counter face to align with duct. 3.
Summary of the content on the page No. 15
Satellite-fill icemaker ice transport tube installation Incorrect ice transport tube installation can result in wet ice and dispensing problems. Follow guidelines below to ensure correct installation. Call factory for assistance if you are unable to meet these requirements. General requirements Maximum length of tube run – 6m (20 ft). Factory approval required for longer runs. Run tube without dips. One continuous length of tube; no splices. Minimum radius of bends in tube – 153mm (6") inside r
Summary of the content on the page No. 16
Additional ice transport tube connection specifications for Vision series ice and beverage dispensers 1. Push one end of ice transport tube(s) through hole(s) provided in side of dispenser. 2. Route tube into ice tube bracket inside dispenser and engage bracket tabs in holes located in end of ice transport tube(s). (see drawings below) 3. Verify bin thermostat capillary tube is mounted correctly. (see drawings below) Ice tube retainer bracket 1" (25mm) ice tube retaining bracket ice tube ice
Summary of the content on the page No. 17
Ice transport tube installation detail install insulation on full run of tube Dispenser Evaporator grommet install clamp behind lip on evaporator port Satellite-fill icemaker start up procedure The start-up procedure below is intended to ensure that icemaker is operating properly after installation has been made. Check each item listed and call factory immediately for assistance if you experience problems with unit. Before turning on power 1. Turn on water to icemaker. 2. Push down on float
Summary of the content on the page No. 18
Monthly condenser cleaning (air-cooled icemaker only) 1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of air-cooled icemakers to ensure optimal performance. 2. When reinstalling counter panels in front of remote icemakers, be sure that ventilation louvers line up with condenser air duct. Fig. 5 Semi-annual evaporator cleaning (every 6 months) Solution A – Ice machine cleaner: Prepare 3.8 Liters (one gallon) of Follett 2 ™ SafeCLEAN Ice Machine Cleaner (one 7 oz
Summary of the content on the page No. 19
Service Icemaker Operation Follett’s icemaker consists of four distinct functional systems: • Refrigeration system • Water system • Harvesting system • Electrical control system These four systems work together to accomplish the production and harvesting of ice. A problem in any one of these systems will result in improper operation of the entire ice production cycle. When troubleshooting the icemaker, it is important to analyze the entire system operation to determine which system is not func
Summary of the content on the page No. 20
RED RED VIOLET VIOLET WHITE BLACK BLACK BLUE Technical specifications (all models) Refrigeration system diagram high side high pressure service port switch condenser filter dryer low side service port evaporator compressor high high low low pressure pressure pressure pressure thermostatic vapor liquid liquid vapor expansion valve C/ET400A/W wiring diagram Follett icemakers used on top of an ice storage bin (C/ET400A/W) have a slightly different circuitry. A diagram for these icemakers is sho
