Craftsman 139.53646SRT2 user manual

User manual for the device Craftsman 139.53646SRT2

Device: Craftsman 139.53646SRT2
Category: Garage Door Opener
Manufacturer: Craftsman
Size: 2.07 MB
Added : 3/10/2014
Number of pages: 40
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Craftsman 139.53646SRT2. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Craftsman 139.53646SRT2.

For your convenience

If looking through the Craftsman 139.53646SRT2 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Craftsman 139.53646SRT2 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Craftsman 139.53646SRT2 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Craftsman 139.53646SRT2 User manual - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Craftsman 139.53646SRT2 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Craftsman 139.53646SRT2. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Owner's
Manual
Model No.
139.53335SRT3
139.53645SRT3
139.53646SRT2
139.53648SRT2
139.53650SRT
139.53660SRT1
139.53834SRT3
For Residential Use
CRAFTSMAN®
Only
GARAGE DOOR OPENER
Caution:
• Safety Precautions
Read and follow all
• Assembly
safety rules and
• Installation
operating instructions
• Adjustment
before first use of this
product. • Care and Maintenance
• Operation
Fasten the manual
• Troubleshooting
near the garage door
• Parts List
after installation.
Complies with UL 325
regulations ef

Summary of the content on the page No. 2

Contents Page Contents Page Installthe lightand lens.................................................19 A reviewof safetyalertsymbols.................................2 You', need tools..........................................................3 Attachemergencyrelease ropeand handle.................19 Electricalrequirememts.................................................20 Safetyinformationregardinggarage doorlocks and ropes..................................................................3 Safet

Summary of the content on the page No. 3

You'll Need Tools Duringassembly, installationand adjustment of the opener, instructionswill callfor hand tools shownbelow. Pencil oDoolooo O L_ Level Hack Saw Tape Measure Wire Cutters Claw Hammer Dnl_ 3/16", 5/16" and 5/32" Dn_l Bits Pliers Stepladder Adjustable End Wrench CAUTION WARNING To avoid damage to the garage door and An unbalanced garage door might not reverse opener, disable locks before installing and when required and someone under the door operating the opener. Use a wood screw o

Summary of the content on the page No. 4

I SECTIONAL Door Installation I Before you begin, survey your garage area to see whether any of the conditions below apply FINISHED CEIUNG to your Installation. Supao_ bracket & is required. Horizontal and vertical reinforcement See page 17. is needed for lightWeight garage doors Slac_ in Chain Tensmn (fiberglass, steel, aluminum, door with grass panels, etc.). is Normal Whe_ See page 24 for details. Garage Door is Closed Header Wall Extension Spring Floor must be ravel across width of dOOr Clos

Summary of the content on the page No. 5

I ONE-PIECE Door Installation I One-Piece__Door Without Track Before you begin, survey your garage area to /_ FINISHED CEILING see whether any of the conditions below apply ____._o _ Supp_= ur_e_ tO your Installation. &lasting _ hardware is required, Slac_ks Chanom_n in tenwtN_nSmn Seepage 17 garage door is dosed, /z le _ Gap _ _ of door rnust not exceed 1/4". Safety Reversing Sensor Based onyour particularrequirements, thereare One-Piece Door With Track several installation steps which mightcel

Summary of the content on the page No. 6

Carton Inventory Your garage door opener is packaged in two cartonswhich contain parts illustratedbelow. Accessorieswill depend on model purchased. If anything is missing, carefully check the packing material. Parts may be "stuck" inthe foam. Hardware for assembly and installationis shownon page 7. Models 53335, Models 53645, 53646 Models 53650, 53834 Model 53645 MOdels 53335 (1),53645 {2), 53646(2), 53648, 53660 S364S(2), 5365O(2), S3660(_), 53S34(2), Three*Function Remote Control DOOrControl B

Summary of the content on the page No. 7

Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. Assembly Hardware Washered Screw Hex Screw Nut Carriage Bolts 5/16"-18xl/2' (2) 5/16'-18x7/8" (3) 5/16'-18 (5) 1/4"-20xl/2" (4) Master Link(2) (mounted in Opener) _!I!'I!/!(!!I!!!/!l!!l'/'/l(!!//!!/II/i/IiIl//ii/I/

Summary of the content on the page No. 8

Assembly Section: Pages 8 - 11 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Make sure bolt necks are Assembly Step 1 seatedIn thesquare ,_ holesandrailsare Assemble the T-rail & Attach alignedbeforeyou tightenlocknuts.(See the Cable Pulley Bracket rightandwrongviews). U Improperassemblycan cause jerky trolley • Align the 3 T-rail sections on a flat surface exactly Wrong operation,noiseand/or Right as shown. The end sections are identical. Make

Summary of the content on the page No. 9

Hardware Shown Assembly Step 2 Actual Size Install the Trolley on the T-rail I • Attach the threaded shaft to the trolley with the lock washer and nuts as shown. LoCk Washer Nut 5/16 ° 5/16" - 18 Lock Washer Outer Nut 5/16"_ Troile_ Temporary Stop Screwdriver • As a temporarystop, insert a screwdriver into the hole in the front end of the T-rail. • Slide the trolleyassembly along the rail to the screwdriverstop. If trolley hits against any nuts on the T-ralt, the bolts and nuts were attached fro

Summary of the content on the page No. 10

Assembly Step 4 WARNING Install the Chain/Cable & Attach the Sprocket Cover Serious Injury can result If fingers become entangled In moving opener sprocket. Attach sprocket cover securely. Never operate opener while your hand Is near the opener sprocket. Dispensing Carton Figure 2 Opener Leave Chain and Cable SprOcket Insole DLspensing Keep Chain and Cable Taut When Dispensing • Detach the cable loop fromthe carton and fasten it to the trolleywitha master linkfrom the hardware bag. See master li

Summary of the content on the page No. 11

Assembly Step 5 Tighten the Chain & Cable I Lock Outer Nut Washer Inner Nut • Spin the inner nut and lock washer down the threaded shaft, away from the trolley. ___z:_:z:z _T°Tighten Outer Nut _ • To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain I_n_r NUt from twisting. • When the chain is approximately 1/2" above the e__ _ To Tighten base of the T-rail at its midpoint, re-tighten the Troll inner nut to secure the adjustment. Sprocket noise can res

Summary of the content on the page No. 12

Installation Section: Pages 12 - 27 Installation Step 1 Determine Header Bracket Location If the header bracket is not rigidly fastened to Installation procedures vary according to a structural support on the header wall or garage door types. Follow the instructions ceiling, the safety reverse system may not which apply to your door. work properly (see page 30). The door might not reverse when required, and could cause serious injury or death. The garage door springs, cables, pulleys, brackets a

Summary of the content on the page No. 13

Read the Safety instructions on page 12. They also apply to doors without tracks. Header Wall Vertical Centedine 2x4 • Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door. If headroom clearance is minimal, you can install the header bracket on the ceiling. OPTIONAL CEILING MOUNT See page 14. FOR HEADER BRACKET If you need to instal/the header bracket on a 2x4 (on wail or ceiling), use lag screws (not provided) to securely fa

Summary of the content on the page No. 14

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for Install the Header Bracket "Installation Step 2 I your particular requirements, Fasten the Header Bracket to the Wall • Center the bracket on the vertical guideline with • Mark either set of bracket holes (do not use the the bottom edge of the bracket on the horizontal holes designated for ceiling mount). Drill 3/16" pilot line as shown (with the arrow p

Summary of the content on the page No. 15

Installation Step 3 Attach the T-rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. If the door spring is in the way you'll need help. Heade_ Have someone hold the opener securely on a Brackel temporary support to allow the T-rail to clear the Cable spring. • Position the cable pulley bracket against the header Bracket bracket. • Align the bracket holes and join with a clevis pin as shown. • Insert a ring fast

Summary of the content on the page No. 16

Installation Step 4 CAUTION Position the Opener To prevent damage to steel, aluminum, Follow instructions which apply to your door fiberglass or glass panel doors, do not rest the type as illustrated. opener on the door without using a 2x4. SECTIONAL Door & ONE-PIECE Door with Track I A 2x4 laid flat is convenient for setting an ideal door-to-T-rail distance. T-rail 2x4 • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough, • Open the door all th

Summary of the content on the page No. 17

Installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On Figure 1 finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not _rovided. See accessory page 38. Supports • Measure the distance from each side of the opener to the structural support. • Cut both pieces of the hanging brac

Summary of the content on the page No. 18

i, Installation Step 6 Install the Door Control Do not connect to live electrical wiring. Connect only to 24 Volt low voltage wires. Connection to Locate the door control within sight of the door live wires or higher voltage may cause setfous at a minimum height of 5 feet where small injury from shock, burn or electrocution. children cannot reach, and away from all moving Children operating or playing with a garage parts of the door and door hardware. door opener can injure themselves or others.

Summary of the content on the page No. 19

6. Attach the User Safety Instruction label to the wall Do NOT connect the power and operate the near the door control, and the Maintenance openerat this time. The trolley will travel to the Instruction label in a prominent location on the full open position but will not return to the inside of the garage door. close position until the sensor beam is connected and properly aligned. Page 32 explains how to use the door control. See Safety Reversing Sensor instructions beginning on page 21. Instal

Summary of the content on the page No. 20

Installation Step 9 I Electrical Requirements I To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. To reduce the risk of electric shock, your garage Do NOTuse an extension cord, 2-wire adapter, door opener has a grounding type plug with a third or change the plug in any way to make it fit grounding pin. This plug will onlyfit into a grounding your outlet. type outlet. If the plug doesn't fit into the outlet you have, contact


Alternative user manuals
# User manual Category Download
1 Craftsman 139.18453D User manual Garage Door Opener 17
2 Craftsman 139.53315SR User manual Garage Door Opener 13
3 Craftsman 139.18473D User manual Garage Door Opener 2
4 Craftsman 139.18452D User manual Garage Door Opener 1
5 Craftsman 139.53225SRT User manual Garage Door Opener 6
6 Craftsman 139.53325SRT User manual Garage Door Opener 3
7 Craftsman 139.18451D User manual Garage Door Opener 3
8 Craftsman 139.18595 User manual Garage Door Opener 1
9 Craftsman 139.53335SRT3 User manual Garage Door Opener 2
10 Craftsman 139.53403 User manual Garage Door Opener 0
11 Craftsman 139.53515SR - I/2HP User manual Garage Door Opener 21
12 Craftsman 139.53425SRT User manual Garage Door Opener 0
13 Craftsman 139.53610 User manual Garage Door Opener 0
14 Craftsman 139.53625SR User manual Garage Door Opener 5
15 Craftsman 139.53628SRT User manual Garage Door Opener 12
16 Sony Remote Commander RM-V111T User manual Garage Door Opener 50
17 Sony RM-B750 User manual Garage Door Opener 22
18 Sony RCP 920 User manual Garage Door Opener 5
19 Aspire Digital ASPIRE RF RFKGT User manual Garage Door Opener 0
20 Aiphone IS-SS-HID-I User manual Garage Door Opener 0