Summary of the content on the page No. 1
280 Machlin Court, City of Industry, CA 91789
(Tel) 800-790-1299 (Fax) 909-718-1949
NOTICE
Dear Customers:
Thank you for choosing our barbeque grill and hope that you enjoy
our product.
Our gas valves and components are preset at the factory to operate
on Liquid Propane (LP). If you wish to convert your grill from LP to
Natural Gas (NG), we strongly recommend that you hire a
professionally trained technician to convert the unit. Please
understand that we will not be responsible for any liability
Summary of the content on the page No. 2
Natural Gas Conversion Style# 710-0650 AWARNING! FALURE TO HEED THESE WARNINGS COULD RESULT IN A FIRE OR EXPLOSION THAT COULD CAUSE SERIOUS BODILY INJURY, DEATH OR PROPERTY DAMAGE. Installation of this Natural Gas Conversion kit must be performed by a QUALIFIED GAS TECHNICIAN ONLY. DO NOT ATTEMPT TO INSTALL THIS KIT YOURSELF. Improper installation could result in a gas leak which could cause a fire or explosion and cause serious bodily injury, death or property damage. Leaks due to improper inst
Summary of the content on the page No. 3
Tools are required for converting from LP to NG. Below tools and orifices are provided. Allen Key 6mm Wrench 6mm Nut Driver NG Rear Burner Orifice NG Searing Side Burner Orifice Below tools are not provided. Phillips Head Screwdriver (+) Monkey Wrench
Summary of the content on the page No. 4
NG Regulator Hose and Regulator Conversion Tools required: Phillips Head Screwdriver (+) Monkey Wrench /_ WARNING Make sure all grill components are completely cooled and gas supply is turned off and removed from grill prior to performing the conversion. 1. Install the regulator hose (short hose) to the end of the regulator marked "OUT." Install the brass connector to the other end of the regulator marked "IN." (If regulator, hose, and brass connector are pre-assembled, you may disregard this st
Summary of the content on the page No. 5
Main Burner Conversion Phillips Head Screwdriver (+) 6mm Nut Driver 1.Remove the rotisserie kit, warming rack, cooking grids, and flame tamers from the firebox. Remove the main tube burners by removing the screw securing the burners near the back wall of the firebox and the screws near the front of the firebox that secure the igniter brackets to the burners. Gently lift the tube burners up and out 2. Locate and remove the LP orifice at the end of each valve with a 6mm nut driver. The main burner
Summary of the content on the page No. 6
Searing Side Burner Conversion Tools required: Phillips Head Screwdriver (+) Allen Key 6mm Nut Driver 6mm Wrench 1.Loosen the igniter wire screws, searing main burner brace screws, and back two screws securing searing side burners. 2. Take out the searing side burner from the firebox. Locate orifice on end of valve and remove by turning counterclockwise with an 6mm nut driver. 3.Insert NG orifice with a 6mm nut driver and secure tightly by turning clockwise. Reinsert the searing side burner, tig
Summary of the content on the page No. 7
Rear Burner Conversion Tools required: Phillips Head Screwdriver (+) Monkey Wrench 6mm Nut Driver 6mm Wrench 1.Remove the cover of the rear burner by removing the screws in the firebox. Use another hand to hold the orifice cover to ensure it doesn't fall. Install burner orifice 2. Use monkey wrench to loosen the orifice nut and take out the orifice holder. Use a 6mm nut driver or Allen key to unscrew and remove the orifice. 3. Replace the orifice for LP gas with the orifice for NG. After the ori
Summary of the content on the page No. 8
10" PVC Gas Hose Conversion Warning!! Gas Valves are preset at the factory to operate on LP gas or NG gas. If you wish to convert, be sure to consult your gas supplier or trained technician for the conversion. After the Natural Gas regulator has been installed, attach the PVC Gas hose to the regulator (See drawing below). Connect the other end of the PVC Gas Hose to the house gas line using the quick-connect fitting. To use the quick connect fitting, lift the head of the connector back. Insert t
