Summary of the content on the page No. 1
GN9020-D
Digital Wireless System
GN9010-BT
Bluetooth™ Wireless System
User Guide
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Summary of the content on the page No. 4
Checking the System Adjusting to your Telephone 5 If your telephone has volume control, set the 10 Put on the headset. volume in the middle position. 11 Make sure the mute 6 Press the headset/handset function is off. If selector to switch on the you hear a beep headset. The headset mode every 3 seconds, the indicator on the base station mute function is on. illuminates. Turn off the mute function by pressing 7 The headset the mute button mode indicator once. on the headset begins flashing 12 Lif
Summary of the content on the page No. 5
17 Using the Adjusting the Microphone Volume headset/handset selector to toggle back and forth 14 Put on the headset. between handset and headset mode, adjust the microphone volume control from 1 to 8 by first talking in the handset and then in the headset in each switch position. Position 1 is 15 Press the headset/handset selector the lowest volume setting to switch to handset mode. and position 8 is the highest volume setting. 18 When the person hears no difference whether you talk in the han
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Adjusting the Receive Volume Recharging the Battery 24 To increase or decrease the 26 To ensure optimum volume, press the upper (+) battery life, when not or lower (-) part of the in use, place the headset oval volume control on in the base station with the headset. When the the headset/handset volume reaches maximum selector in the handset or minimum, you will hear position. The battery a beep in your headset. charging indicator illuminates during recharging. It takes 3 hours to fully charge t
Summary of the content on the page No. 8
30 To change or clean Comfort Adjustments the leatherette ear cushion, first 28 You can wear the remove the earplate headset on your by turning the right or left ear, earplate 45 degrees whichever side you counter-clockwise. prefer. To switch Once removed, the sides, simply rotate ear cushion can be the microphone taken off the boom below the earplate. headband. NOTE: Do not force the To use the optional boom over the top foam ear cushion, of the headset. first remove the earplate and 29 Adjust
Summary of the content on the page No. 9
Summary of the content on the page No. 10
Cautionary Notes to Computer Users When using any headset with a computer, care should be taken in dry or low humidity environments to protect the user from electrostatic discharge from the monitor (CRT). Computer monitors can induce a substantial electrostatic charge when turned on or off, or when there is a power failure, and the resulting electrostatic discharge can be passed through the headset to ground. A user in close proximity to or touching the computer may feel a common “shock” sensat
Summary of the content on the page No. 11
Safety Instructions • Never try to dismantle the product yourself. None of the internal components can be repaired by users. • Do not expose the headset to rain or other liquids. • The headset is equipped with a rechargeable NiMH battery (nickel-metal-hydride). For battery replacement, please contact your distributor or reseller.
Summary of the content on the page No. 12
FCC Notice to Users Upon request only, you must notify your telephone utility company (telco) of your intention to install or permanently remove an FCC Part 68 registered device or system. Include the FCC Registration Number and the Ringer Equivalence Number (REN) located on the amplifier label. The telco has the right to make changes to their network, which may affect the operation of your equipment, provided you are given adequate advance written notice to permit correct operation. This device
Summary of the content on the page No. 13
IC Notice to Users The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirement as prescribed in the appropriate Terminal Equipment Technical Resource Document(s). The department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
Summary of the content on the page No. 14
Warranty GN Netcom, Inc. warrants this product against all defects in material and workmanship for a period of one year from the date of original purchase. The conditions of this warranty and our responsibilities under this warranty are as follows: • The warranty is limited to the original purchaser. • The warranty is void if the serial number, date code label or product label is removed, or if the product has been subject to physical abuse, improper installation, modification, or repair by unau
Summary of the content on the page No. 15
To Obtain Service For customer service and technical support, call GN Netcom, Inc. at 1-800-826-4656. If it becomes necessary to send a unit in for repair, it is not necessary to call for a Return Material Authorization (RMA) number, as one will be assigned upon receipt of the package at the factory. Ship the product in a suitable shipping container, fully insured and with the shipping charges prepaid. Include the following with the product: • Your name, company name, address and telephone numbe
Summary of the content on the page No. 16
1555-769 77 Northeastern Blvd. • Nashua, NH 03062 USA Printed in USA 1-800-826-4656 • www.gnnetcom.com September 2000
