Summary of the content on the page No. 1
Personal Security
Motion Sensor
with Keypad
User Manual
Do not use in wet locations
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Motion Sensing Alarm With Remote Control Alarm/Chime Switch Indicator Light Wall Mount Motion Sensing Alarm Low Battery Indicator The Motion Sensing Alarm has a low battery indicator light. When the batteries need to be replaced, the indicator will flash slowly. Average battery life for typical usage is up to one year.
Summary of the content on the page No. 4
INSTALLING BATTERIES The battery compartment is located on the back of the unit. 1. Remove the battery compartment screw and slide off cover in the direction of the open arrow. 2. Insert (3) AA batteries (not included) . Take care to note the polarity diagram inside the battery compartment. 3. Replace the cover and secure screw. Battery Compartment Learn Learn Button
Summary of the content on the page No. 5
CREATING YOUR PERSONAL ALARM CODE The -digit keypad allows you to set a personal code for arming and disarming the alarm. 1. Remove the battery compartment screw and slide off cover in the direction of the open arrow. 2. Press the LEARN button once; the red indicator light on the front of the alarm will blink for 1 seconds. During this time, input your -digit code. A beep will confirm each input. The unit will flash a green light 3 times to confim your new -digit code has be
Summary of the content on the page No. 6
flexibility to aim the motion sensor in a particular direction. 1. Choose your desired location, such as the corner of the room. This will provide maximum coverage. NOTE: The sensor has a 1-20 ft. detection zone, with approximate angles of 110 degree horizontal x 70 degree vertical. Recommended installation height is to 8 feet. 20' 15' 110˚ 10' 5' Feet 6'-8 ' 70˚ Feet 5' 10' 15' 20'
Summary of the content on the page No. 7
7 2. Secure ball and socket mount to the wall using either the provided wall anchors or by screwing directly into a wall stud. Once installed securely on the wall, slide insert bracket of mount into the back of the unit and lock in place. The mount will click when secured to the alarm. OPERATING IN THE ALARM MODE 1. Locate the ALARM/CHIME switch on the side of the alarm.
Summary of the content on the page No. 8
8 2. Slide switch to ALARM mode. Arming the Alarm 1. Arm the alarm by pressing your -digit code. A beep will sound after each button is pressed. 2. When the -digit code is entered correctly the unit’s indicator light will flash green once. If entered incorrectly, the unit will sound and the indicator light will flash red three times. 3. A red light will immediately begin to flash indicating the -second exit delay has started. The delay allows time for you to leave the protected
Summary of the content on the page No. 9
in 30 seconds. The siren will sound for 30 seconds (unless disarmed by the remote) and then turn off. In 1 seconds the alarm will check for motion. If motion is detected, the siren will sound again. The cycle will repeat until the unit is disarmed with the remote. Disarming the Alarm 1. When returning to the protected area, simply enter your -digit code within 30 seconds to disarm the alarm. 2. When the fourth digit of your code is entered, the unit will respond with two tones a
Summary of the content on the page No. 10
10 sounded to deactivate. NOTE: To test, a cloth can be used to cover the alarm to reduce risk of hearing damage. Incorrect Code If an incorrect code is entered the unit will sound a louder beep and the indicator light will flash red 3 times. Re-enter correct code after indicator light stops flashing. OPERATING IN THE CHIME MODE The chime is used to notify you when motion is sensed in the area. 1. Slide switch to CHIME mode; the chime will sound once. • Activating the Chime: The chi
Summary of the content on the page No. 11
11 • Deactivating the Chime: To deactivate the chime, slide the switch to ALARM. TESTING MOTION SENSOR OPERATION 1. Set alarm to CHIME mode; the chime will sound once. 2. After initial chime, wait 1 seconds and wave hand in front of the sensor. If chime sounds immediately, sensor is working correctly. 3. To turn unit off, set unit to Alarm mode. CARE AND MAINTENANCE To clean the unit housing, use a soft cloth slightly dampened with water and wipe dry. Do not use chemical agents as
Summary of the content on the page No. 12
12 WARNING Limitations of Alarm Products This product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, JASCO is not an insurer, this product is neither insurance nor a guarantee that such an event will be prevented, and users should protect themselves with proper insurance. JASCO makes no representation that this product cannot be compromised or circumvented, that
Summary of the content on the page No. 13
13 WARNING Risk of personal injury • Prolonged exposure to alarm siren may cause permanent hearing loss Battery Warning • Remove batteries before storing the Alarm for extended periods • Batteries may leak harmful liquids or ignitable materials or explode causing injury and product damage • Do not mix old and new or other battery types • Replace all batteries at the same time • Replace fully discharged batteries immediately For indoor use only; do not use in wet locations. This Jasco product
Summary of the content on the page No. 14
1 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 1 o f the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee t
