Summary of the content on the page No. 1
E
V
O
T
S
C
S
O
E
M
T
Owners Manual
HOW TO ORDER REPAIR PARTS
Model 2931
This manual will help you to obtain efficient, dependable service
WONDERWOOD
from the heater, and enable you to order repair parts correctly.
THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR
Keep this manual in a safe place for future reference.
When writing, always give the full model number which is on the
*ASSEMBLY
nameplate attached to the inside of the cabinet door of the
*INSTALLATION
heater.
*OPERATION
*REPAIR PARTS
Whe
Summary of the content on the page No. 2
Notes TOOLS AND MATERIAL NEEDED TOOLS MATERIALS Pencil Chimney Connection- 6" Dia. Black 6 Foot Folding rule or tape Steel (24 Ga. minimum): Straight or Tin Snips Corrugated Elbow (as required)* Drill, hand or electric 1/2" Sheet Metal Screws Drill bit, 1/8" dia. 6" Inside Diameter Underwriters (for sheet metal screws) Laboratories (UL) listed Residential Gloves Type and Building Heating Appliance Screwdriver (blade-type) Chimney, Type "HT", or 6" existing 5/16" Nut Dri
Summary of the content on the page No. 3
RULES FOR SAFE INSTALLATION AND OPERATION Read these rules and the instructions carefully. Notes SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. 1. Check local codes. The installation must 9. For further information on using your heater comply with their rulings. Do not install this safely, obta
Summary of the content on the page No. 4
LOCATING THE HEATER AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND: STOP: Before connecting 1. The chimney connection should be as short F36 BLOWER KIT the flue pipe, check the as possible. The heater must have its own "SOLID FLUE DAMPER chimney flue. Do not connect this unit to a An Optional Blower kit is available for the 2931 Wonderwood chimney flue serving another appliance. If there INSTALLATION". automatic wood burning circulator heater. If this kit is not available is no chimney
Summary of the content on the page No. 5
INSTALLING FLUE COLLAR This heater has been shipped with the flue collar unattached for shipping purposes. To install the flue collar simply follow the instructions below. The following parts are necessary to install the flue collar: SAFETY NOTICE 1 - Flue collar 1 - Flue collar gasket In the unlikely event that your 2931 "overfires" (a condition evidenced by elbows, 6 - 1/4-20x3/4" bolts stovepipes, and connectors glowing red in appearance or otherwise discoloring), 6 - 1/4-20 Kep nuts then you
Summary of the content on the page No. 6
D N R O I T S A C R E 6 P I M N REPAIR PARTS LIST - MODEL 2931 (SEE PAGE 18) SOLID FLUE DAMPER INSTALLATION AUTOMATIC WOOD BURNING CIRCULATOR This unit comes equipped with a solid flue damper which is intended to be installed into the flue collar. The following instructions will help guide you in Key No. Description Qty. Part No. installing the solid flue damper. 1 Fire Grate 2 40076 1. Before you connect the 6" flue pipe to the flue 2 Ash Pan 1 67444 collar, place the solid damper inside of th
Summary of the content on the page No. 7
22 23 37 15 43 16 11 35 12 18 17 14 10 19 9 13 21 20 44 38 34 31 24 39 7 29 30 28 6 8 36 5 41 4 33 42 41 25 32 26 42 3 2 REPAIR PARTS 25 26 AUTOMATIC WOOD BURNING CIRCULATOR HEATER MODEL 2931 - INTERIOR 1 of which is apparent: The chimney CHIMNEY CONNECTION provides a means for exhausting smoke and flue gases resulting from combustion Two basic types of chimneys are ap- of the fuel. Secondarily, though, the proved for use with solid fuel: Factory- chimney provides "Draft" which allows built and
Summary of the content on the page No. 8
FIG. 6A - Thru-The-Wall Installation REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER NON-COMBUSTIBLE WALL MODEL NUMBER 2931 THIMBLE (SEE PAGE 16) COLLAR PIPE REPAIR PARTS LIST BAROMETRIC KEY NO. PART NO. DESCRIPTION QTY. DRAFT CONTROL (OPTIONAL) 1 89411 Mesh Brass Trim (LH/RH) 2 CLASS A UL 103HT FLOOR PROTECTOR 2 89410 Mesh Brass Trim (TOP, BOTTOM) 2 CHIMNEY KIT INCLUDING WALL THIMBLE. 3 23230 Cabinet Front Mesh 1 4 89413 Cabinet Front Brass Trim (left) 1 5 89414 Cabinet Top Brass Trim 1
Summary of the content on the page No. 9
5 9 8 14 14 10 4 13 12 16 15 17 11 3 19 18 7 1 6 2 REPAIR PARTS AUTOMATIC WOOD BURNING CIRCULATOR HEATER MODEL 2931 - EXTERIOR VENTING INTO A FIREPLACE (Not recommended) Many people may wish to convert an Many prefabricated fireplaces fall into existing fireplace to heater use. Usually, the "zero-clearance fireplace" category. safe connection of stovepipe to a ma- This is a factory metal fireplace with sonry chimney requires more effort than multi-layered construction. It is designed con
Summary of the content on the page No. 10
FIREPLACE INSTALLATION Connection of the stovepipe directly into Install the stovepipe as far as possible CABINET DOOR KNOB ASSEMBLY the existing masonry chimney over the into the thimble, but not past the inside fireplace opening is the only approved of the flue lining. There should be a The door knob is mounted inside of the cabinet door to facilitate method. This installation performs bet- small air space (approximately 1/2 in.) shipping and must be reversed for proper usage. ter, yielding e
Summary of the content on the page No. 11
When considering a masonry chimney, solid fuel appliance must not be joined to SERVICE HINTS round tiles are preferable to square or a chimney flue which is connected to Do not expect a heater to draw. It is the 4. If the chimney is too cool, water will rectangular, as round tiles have much another appliance burning other fuels. chimney that creates the draft. Smoke condense in the chimney and run back better airflow characteristics and are far spillage into the house or excessive into the sto
Summary of the content on the page No. 12
RULES FOR CONNECTOR PIPE INSTALLATION OPERATING INSTRUC- 1. The crimped end of the stovepipe fits TIONS 5. Seal each connector pipe joint with inside the heater flue collar. Install ad- FUEL furnace cement. Also seal the pipe at CAUTION: BUILD A FIRE ON THE ditional pipe and elbow with the Hardwood, 18" to 23" should be split the chimney. INTEGRAL GRATE THAT IS PRO- CRIMPED END TOWARD THE and air dried (seasoned) for 6 months to VIDED WITH THE HEATER. HEATER. This will allow any obtain maximum
