Summary of the content on the page No. 1
Summary of the content on the page No. 2
VIVOTEK Table of Contents Overview3 Read Before Use �������������������������������������������������������������������������������������������������������������������������������������3 Package Contents �����������������������������������������������������
Summary of the content on the page No. 3
VIVOTEK Overview Read Before Use The use of surveillance devices may be prohibited by law in your country � The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use� It is important to first verify that all contents received are complete according to the Package Contents listed below� Take n
Summary of the content on the page No. 4
VIVOTEK Physical Description Front Panel Light Sensor Lens Built-in Microphone Back Panel Audio Out BNC Video Out Status LED Microphone In SD/SDHC Card Slot External/Internal NTSC/PAL Switch MIC Switch Power Cord Socket Ethernet 10/100 RJ45 Socket General I/O Terminal Block Recessed Reset Button Focus Assist Button (IP8151P Only) DC-iris Control Cable Socket (IP8151) or P-iris Control Cable Socket (IP8151P) Lens Focus Controller Zoom Controller General I/O Terminal Block This Network Came
Summary of the content on the page No. 5
VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method� 12V PIN 1 Power+12V PIN 2 Digital output +12V PIN 3 Digital input PIN 4 Ground Status LED The LED indicates the status of the Network Camera� Item LED status Description Steady Red Power on and system booting 1 Red LED unlighted Power off Steady Red + Blink Green every 1 sec� Network works (heartbeat) 2 Steady Red + Green LED unlighted Network fail 3 Steady Red + Blink Green every 2 sec� Audio mute (he
Summary of the content on the page No. 6
VIVOTEK Hardware Reset Status LED Recessed Reset Button The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation If � the system problems remain after reset, restore the factory settings and install again� Reset: Press and release the recessed reset button with a paper clip or thin object� Wait for the Network Camera to reboot� Restore: Press and hold the recessed reset button until the s
Summary of the content on the page No. 7
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection� 1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block� 2� Connect the camera to a switch via Ethernet cable� 3� Connect the power cable from the Network Camera to a power outlet� 3 1 1: Power +12V 2: Digital output 3: Digital input 4
Summary of the content on the page No. 8
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1� Connect your Network Camera behind a router, the Internet environment is illustrated below � Regarding how to obtain your IP address, please refer to Software Installation on page 10 for details� IP P a ad dd dr re es ss s :: 1 19 92 2..1 16 68 8..0 0..3 3 W WA AN (Wide Area Network ) N (
Summary of the content on the page No. 9
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable� power + data transmission PoE Switch When using a non-PoE switch If your switch/router
Summary of the content on the page No. 10
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to launch the program� 2� The program will conduct an analysis of your network environment� After your network environment is analyzed, please click Next to continue the program� 3� The program will search fo
Summary of the content on the page No. 11
VIVOTEK Ready to Use 1� Access the Network Camera on the LAN� 2� Retrieve live video through a web browser or recording software� User's Manual - 11
Summary of the content on the page No. 12
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN� If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (ex. Microsoft Internet Explorer, Mozilla Firefox, or Netscape). 2. Enter the IP addre
Summary of the content on the page No. 13
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 27� ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser� 1� Choose Tools > Internet Options > Security > Custom Level� ® 2. Lo
Summary of the content on the page No. 14
VIVOTEK Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player 1� Launch the RTSP player� mpegable Player mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3� The address format is rtsp://:/
Summary of the content on the page No. 15
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet � For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 7� To utilize this feature, please check the following settings on your Network Camera: 1� Because most players on 3GPP mobile phones do not support RTSP authentication, make
Summary of the content on the page No. 16
VIVOTEK Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Channel list� For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www�vivotek�com� 16 - User's Manual
Summary of the content on the page No. 17
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� Resize Buttons VIVOTEK INC. Logo Host Name Camera Control Area Live View Window Configuration Area Hide Button NOTE ► “Focus Assist“ and “Iris Adjustment (P-iris)“ are not supported by the IP8151. VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host Name The host name
Summary of the content on the page No. 18
VIVOTEK Focus Assist (IP8151P only) Please follow the steps to fine-tune the camera focus: 1. Adjust the C- or CS-mount ring and fix the shooting direction. 2. Click “on“ to enable the focus assist function, then the Live Video Window will become full screen for precise focus adjustment� 3� Push the focus assist button on the back panel of the camera, then a floating indicator will be displayed on screen showing detailed focus information, which will change in accordance with the manual
Summary of the content on the page No. 19
VIVOTEK Configuration Area Client Settings: Click this button to access the client setting page � For more information, please refer to Client Settings on page 22� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a password be applied to the Network Camera so that only the administrator can configure the Network Camera� For more information, please refer to Configuration on page 24� Language: Click this button to choose a languag
Summary of the content on the page No. 20
VIVOTEK Snapshot: Click this button to capture and save still images � The captured images will be displayed in a pop-up window Right-click � the image and choose Save Picture As to save it in JPEG (*jpg) or BMP � (*�bmp) format� Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation. The navigation screen indicates the part of the image being magnified. To control the zoom level, drag the slider bar. To move to a different area you want to magnify, drag the
