Summary of the content on the page No. 1
Home Theater Fixed Frame Curved Projection Screen
Lunette Series
1
Rev.052611‐AS
www.elitescreens.com info@elitescreens.com
Summary of the content on the page No. 2
Important Safety & Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your screen. 1. Please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated to hang the screen. 2. Regardless if the screen is installed inside or on the wall, make sure that the proper mounting anchors are used and that the weight is supported appr
Summary of the content on the page No. 3
Parts List for the Lunette Series Please make sure all parts listed below are included before proceeding with the installation. A. Dry‐wall anchor B. 1.77” L‐Bracket C. 3.54” L‐Bracket D. Y‐Bracket E. M5 Screw F. Wood Screw G. Fix Plate H. Center Support Bar I. Support Joiner J. Elbow Joint
Summary of the content on the page No. 4
Installation Instructions Assembly 1. Insert both Elbow Joints (J) into each Horizontal Curved Frame (N) and join all four frame parts together as shown below. 2. After making sure that all four corners join at right angles to form a perfect rectangle and fasten together with the M5 screws (E). Minimal gap is normal here 3. Lay out the Screen
Summary of the content on the page No. 5
4. Insert the screen Tension Rods (L) through the sleeves according to their corresponding length on each edge of the screen. 5. Slip the tension rods into the grooves running along each side on the back of the frame. Clip on the Fix Plates (F) to the back of the frame to secure the rods into place forming a tight and flat surface. Tension Rod Fix Plate Viewing Surface 5 Rev.052611‐AS www.elitescreens.com info@elitescreens.com
Summary of the content on the page No. 6
Black Backingg for AccousticP Pro1080 0 Mode els This proce edure only ap pplies to Acou usticPro 1080 0 models, disrregard if yourr curved frame us now an AcousticP Pro 1080 variaant. The blackk backing counters the effe ects of light p penetration th hat would otherwise e light up all ittems behind the screen an nd spoil the p picture. The black b backing goes b behind the pro ojection surfacce and is held into position b by Velcro‐faced d fix plates.
Summary of the content on the page No. 7
ATTACH THE FIX PLATES 1. Make sure that the material and frame are lying face down on a clean, dry and non‐abrasive surface. 2. Center the material inside the frame. Note: The material will be noticeably smaller because stretching the material is required to create a sufficient amount of tension for perfect material flatness. 3. Start attaching the Fix Plates in the center of the Horizontal Curved Frame’s edge and (1) then alternate with the center short sides (2). Note: Fo
Summary of the content on the page No. 8
CENTER SUPPORT BAR 1. Insert the Support Joiner (I) into each side of the Center Support Bar (H) to complete assembly. Support joiner Center support bar 2. Insert the Center Suppor
Summary of the content on the page No. 9
INSTALLATION Wall Horizontal Curved Frame Mid‐Point (Y‐Bracket) L‐Point (L‐Bracket) R‐Point (L‐Bracket) 9 Rev.052611‐AS www.elitescreens.com info@elitescreens.com
Summary of the content on the page No. 10
1. Locate your desired installation height, draw the Datum Line and mark the drill‐hole area of the Mid‐Point. Note: The center of the hole must align with the Datum Line. 2. Mark the drill‐hole area of the L‐Point and the R‐Point. The top of the bracket must align with the Datum Line. 3. Drill a hole with the proper bit size according to the included Wood Screws (F). 4. Line up the brackets with the drilled holes on the installation location and screw then in using a
Summary of the content on the page No. 11
Model Numbers Parts List Curve235- Model Number 85w 96w 103w 115w 125w 138w 147w 158w Part Name Horizontal Curved Frame 2 2 2 2 2 2 2 2 Upright Vertical Frame 2 2 2 2 2 2 2 2 Elbow Joint 4 4 4 4 4 4 4 4 M5*15 Assembly Screw 9 9 9 9 9 9 9 9 Screen Material 1 1 1 1 1 1 1 1 Top/Bottom Tension Rod 2 2 2 2 2 2 2 2 Side Tension Rod 2 2 2 2 2 2 2 2 Center Support Bar 1 1 1 1 2 2 2 2 Support Joiner 2 2 2 2 4 4 4 4 Fix Plate 44 52 52 56 62 66 68 72 Dry
Summary of the content on the page No. 12
L Lunette Series Dimens sion Ta able1 Unit:mm Diago onal Over rall Viewing Frame O Overall View wing Frame Model Size/As spect Widt th Width Width H Height Heig ght B2 C Depth E Ratio (A) ) (A1) (A2) (B) (B1) (D) Curve235-85 5W 85"(2.3 35:1) 216 66 1986 90 1025 84 45 90 86 40 1050 Curve235-96 6W 96"(2.3 35:1) 242 23 2243 90 1134 95 54 90 98 40 1150 Curve235-103 3W 103"(2..35:1) 258 87 2407 90 1204 102 24 90 106 40 1200 C
Summary of the content on the page No. 13
Warranty Policy • Two (2) Year parts and labor warranty from defects in workmanship from purchase date as follows (except for refurbished units as specified below). • Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government, Educational, Military, & Religious) purchases of new product only. • Refurbished Units carry a 90‐DAY parts and labor warranty. • Each party will be responsible for one way shipping during the warranty period. • A RMA (Return
Summary of the content on the page No. 14
Contact Info US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877‐511‐1211 #3 or fax +1‐562‐926‐8433 Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49‐(0) 40‐30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86‐(0) 755‐8461‐7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.tw or call +866+2+8990‐19
