Summary of the content on the page No. 1
Owner's Manual
PNEUMATIC
AIR HAMMER
Model No.
875.191190
WARNING:
Before operating tool, read this
manual and follow all
Safety Recommendations and
Operating Instructions.
• Safety
• Warranty
• Features & Operation
• Maintenance
• EspaSol
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
www,sears,com
Summary of the content on the page No. 2
FULL TWO YEAR WARRANTY ON Read Operating Instructions CRAFTSMAN AIR-DRIVE TOOLS Please become familiar with all the instructions and If this Craftsman tool fails to give complete satisfaction warnings before operating any pneumatic tool. within two years from the date of purchase, RETURN IT Always Wear Approved Eye Protection TO THE NEAREST SEARS STORE IN THE UNITED Impact resistant eye protection should meet or exceed STATES, and Sears will repair it free of charge. If this the standards set fo
Summary of the content on the page No. 3
More than 1/100 slope _ _1 Main line = 3 times _Branch line = 2 times[_ j Filter I Tool inlet/hose size Stop Regulator Valve Lubricator I Tool inlet_os_ Stop I Valve K% Air Tool i_ jAute Drain Air L Compressor J I_ Valve Figure 1 * Air Hose Hook Up ..\ ..\\..............t...., USING QUICK CHANGE RETAINER Lubrication 1. Disconnect air supply and remove all accessories. An in-line tilter-regulator-lubricator (fig 1) is 2. Thread quick change chisel retainer onto end of recommended as it increases
Summary of the content on the page No. 4
Sears CRAFTSMAN Model 875.191190 Pneumatic Air Hammer Exploded View and Parts List Ref. Description Part No. Ref. Description Part No. 1 Handle 9AH-15001 10 Spring 9AH-15010 2 Spring Pin (2) 9AH-15002 11 Air Inlet 9AH-15011 3 Steel Washer 9AH-15003 12 Upper Valve 9AH-15012 4 13 Valve Disc 9AH-15013 Coil Spring 9AH-15004 5 14 Lower Valve 9AH- 15014 Air Regulator 9AH-15005 6 15 Piston 9AH-15015 Trigger 9AH-15006 7 Coil Spring 9AH-15007 16 Cylinder 9AH-15016 8 Valve Stem 9AH-15008 17 Spring Retaine
Summary of the content on the page No. 5
Troubleshooting 1, Grit or gum in tool 1. Flush the tool with air tool oil or gum Tool runs slowly or will not operate solvent, 2, No oil in tool 2. Lubricate the tool according to the lubrication instructions in this manual 3, Low air pressure 3. a. Adjust the regulator on the tool to the maxi- mum setting b. Adjust the compressor regulator to tool maximum of 90 psi. 4, Air hose leaks 4. Tighten and seal hose fittings if leaks are found, Use teflon tape. 5, Pressure drops 5. a. Be sure the hose
Summary of the content on the page No. 6
DOS AI_IOS COMPLETOS DE GARANTIA DE LAS Lea las instrucciones de operacibn HERRAMIENTAS DE OPERACION NEUMATICA CRAFTSMAN Por favor familiadcese con todas las instrucciones y Siesta herramienta Craftsman no le proporciona una satisfacci6n advertencias antes de operar cualquier herramienta completa dentro de los dos aSos de lafecha de compra, neum_tica. DEVUELVALAA LATIENDA MASCERCANA DE SEARSEN LOS Siempre use proteccibn aprobada para la vista ESTADOS UNIDOS, y Sears la raparaci6n libre de cargo.
Summary of the content on the page No. 7
_,, in_inaciOn m_sde 11100 [_ IT Tubeea derivada = 2 vecesla Filtro I I Zuberia princip al =3 vecesla V_lvula Reguladcr entrada de la herramienta/ entrada de la herramienta/ de cierre Lubricador tama_o de la manguera tarnar_ode I V_Ivula de cierre autedrenaje Herramienta de aire t V_lvula de q _VSlvula de autodrena]e Figura 1 - Preparacibn de Tuberia de Aire Recomendada USO DE UN RETENEDOR DE CAMBIO RAPIDO Lubricacide 1, Desconecte el suministro neumatico y extraiga todos los Se recomienda usar
Summary of the content on the page No. 8
Martillo neumbtico Modelo 875.191190 CRAFTSMAN Sears Vista desplegada y lista de piezas Ref. Descripcibn No. de pieza Ref. Descripcibn No. de pieza 1 10 Resorte 9AH-15010 Mango 9AH-15001 2 11 Entrada neum_tica 9AH-15011 Clavija del resorte (2) 9AH-15002 3 Arandela de acero 9AH-15003 12 Valvula superior 9AH-15012 4 Muelle 9AH-15004 13 Disco de v_lvula 9AH-15013 5 14 Valvula inferior 9AH-15014 Regulador neumatico 9AH-15005 6 Activador 9AH-15006 15 Pist6n 9AH-15015 7 Muelle 9AH-15007 16 Cilindro 9A
Summary of the content on the page No. 9
Localizacibn de fallas La herramienta funciona con lentitud o no funciona 1. Limpie la herramienta con aceite de herramienta 1, Suciedad o goma en la herramienta neum_tica o solvente para goma, 2. Lubrique la herramienta de acuerdo con las 2, No hay aceite en la herramienta instrucciones de lubricaci6n en este manual 3. a. Ajuste el regulador en la herramienta a la 3. Presi6n neum_tica baja graduaci6n m_xima b. Ajuste el regulador del cempreser a la m_xima de la herramienta de 90 psi, 4. Ajuste
Summary of the content on the page No. 10
Your Home For repair- in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-MY-HOME ® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) ....... www.sears.eom www.sears.ca Our Home or
