Grizzly G5792 user manual

Summary of the content on the page No. 1

model g5791/g5792
1
17-piece ⁄2" impact Wrench &
ratchet Kit
instruction manual
Copyright © MAy, 2008 By grizzly industriAl, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#jM10705 printed in tAiWAn

Summary of the content on the page No. 2

safety for your own safety read instruction manual before operating this equipment t he purpose of safety symbols is to attract your attention to possible hazardous conditions. t his manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. t he progression of symbols is described below. r emember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. in

Summary of the content on the page No. 3

7. avoid entanglements. do not 16. do not force tool. it will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. checK for damaged parts parts, when operating this tool. Wear before using. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. use correct air pressure. and any oth

Summary of the content on the page No. 4

inventory 1 ⁄4" npt Air Fitting C B d A F g e h i j Case lubricator ratchet ITEM G5791 G5792 1 A 9mm 7/16" ⁄2" impact Wrench B 10mm 1/2" C 11mm 9/16" D 13mm 5/8" E 14mm 11/16" F 17mm 3/4" G 19mm 13/16" tool oil Bottle H 22mm 15/16" 4mm hex Wrench I 24mm 7/8" J 27mm 1" figure 1. Model g5791/g5792 inventory. 1 Model g5791/g5792 17-piece ⁄ 2" impact Wrench and ratchet Kit -3-

Summary of the content on the page No. 5

operations impact Wrench specifications 1 drive size ............................................... ⁄2" 5 Bolt size Capacity ................... ⁄8" or 16mm no-load speed ........................ 7,000 rpM Maximum torque .......................... 260 ft/lb 1 Air inlet size ................................... ⁄4" npt Air Consumption ........................... 4.5 CFM operating pressure ......................... 90 psi Maximum operating pressure ....... 120 psi r ead the manual before operatio

Summary of the content on the page No. 6

impact Wrench Forward/reverse dial 1 your new ⁄2" drive impact wrench (f igure 3) generates up to 260 ft/lbs. of torque. o nly use thick-walled impact sockets with this air tool. t he common thin-walled chrome sockets may explode if used as impact sockets, causing serious injury. At the end of the handle you can adjust the figure 4. ratchet locations. torque setting by pushing the knob in and turning the knob to 1, 2, 3, or 4; 1 is the lowest torque setting. daily maintenance your impa

Summary of the content on the page No. 7

impact W rench REFPART # DESCRIPTION REFPART # DESCRIPTION 1 P5791001 HOUSING 26 P5791026 ROTOR BLADE 2 P5791002 VALVE BUSHING 27 P5791027 REAR CYLINDER PLATE 3 P5791003 REVERSE VALVE 28 P5791028 BALL BEARING 4 P5791004 TRIGGER 29 P5791029 FRONT CYLINDER PLATE 5 P5791005 ROLL PIN 30 P5791030 ROLL PIN 6 P5791006 VALVE STEM 31 P5791031 COMPRESSION SPRING 7 P5791007 32 P5791032 PIN AIR INLET 1/4 NPT 8 P5791008 BALL SEAT 33 P5791033 GASKET 9 P579100

Summary of the content on the page No. 8

ratchet REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P5791101 HOUSING 124 P5791124 IDLER GEAR PIN 102 P5791102 AIR INLET 125 P5791125 IDLER GEAR PLATE 103 P5791103 THROTTLE LEVER 126 P5791126 CLAMP NUT 104 P5791104 ROLL PIN 127 P5791127 BUSHING 105 P5791105 VALVE BUSHING 128 P5791128 BUSHING 106 P5791106 VALVE STEM 129 P5791129 CRANK SHAFT 107 P5791107 O-RING 130 P5791130 DRIVE BUSHING 108 P5791108 COMPRESSION SPRING 131 P5791131 RATCHE