Summary of the content on the page No. 1
Cordless Impact
Driver
Equipped with Electric Brake
MODEL 6916D
002791
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Summary of the content on the page No. 2
SPECIFICATIONS Model 6916D Machine screw 4 mm - 8 mm (5/32” - 5/16”) Capacities Standard bolt 5 mm - 12 mm (3/16” - 1/2”) High tensile bolt 5 mm - 10 mm (3/16” - 3/8”) No load speed (RPM) 0 - 2,300/min. Impacts per minute 0 - 3,000 Overall length 168 mm (6 - 5/8”) Net weight 1.5 kg (3.3 lbs) Rated voltage D.C. 12 V Standard battery cartridges 1222,1234,1235 • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFE
Summary of the content on the page No. 3
Electrical Safety Tool Use and Care 4. A battery operated tool with integral bat- 12. Use clamps or other practical way to teries or a separate battery pack must be secure and support the workpiece to a recharged only with the specified charger stable platform. Holding the work by hand or for the battery. A charger that may be suit- against your body is unstable and may lead able for one type of battery may create a risk to loss of control. of fire when used with another battery. 13. Do not forc
Summary of the content on the page No. 4
22. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 21. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of may result in a risk of injury. shock or injury. SPECIFIC SAFETY RULES USB024-2 DO NOT let comfort or familiarity with product (gained from
Summary of the content on the page No. 5
SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts .../min................revolutions or reciprocation per minute ................... direct current ................number of blow ................... no load speed n ˚ IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE ENC004-1 1. Before using battery cartridge, read all instruc- (1) Do not touch the terminals with any con- tions and cautionary markings on (1) battery ductive material. charger, (2)
Summary of the content on the page No. 6
FUNCTIONAL DESCRIPTION 002792 Installing or removing battery cartridge 1 • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the 2 battery cartridge with the groove in the housing and slip 1. Button it into place. Always insert it all the way until it locks in 2. Battery cartridge place with
Summary of the content on the page No. 7
CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. 001266 Installing or removing driver bit or
Summary of the content on the page No. 8
The proper fastening torque may differ depending upon the OPERATION kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. 002795 Hold the tool firmly and place the point of the driver bit in the Standard bolt screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to N.m start operation. (ft.lbs) 80 (58) M12(1/2”) NOTE:
Summary of the content on the page No. 9
4. The manner of holding the tool or the material of driving position to be fastened will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fastening torque. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brush
Summary of the content on the page No. 10
EN0001-1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. Ni-Cd 2. a) Take the battery to your nearest Makita Factory Ser- vice Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been desig- nated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine
Summary of the content on the page No. 11
Memo 11
Summary of the content on the page No. 12
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
