Summary of the content on the page No. 1
Impact Driver
Equipped with Electric Brake
MODEL 6951
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Summary of the content on the page No. 2
SPECIFICATIONS Model 6951 Machine screw 4 mm - 8 mm (5/32” - 5/16”) Capacities Standard bolt 6 mm - 12 mm (7/32” - 1/2”) High tensile bolt 6 mm - 12 mm (7/32” - 1/2”) No load speed (RPM) 0 - 2,200/min. Impacts per minute 0 - 3,000 Max. fastening torque 98 N.m (72.4 ft.lbs) Dimensions (L x W x H) 239 mm x 60 mm x 180 mm (9-3/8” x 2-3/8” x 7-1/8”) Net weight 1.3 kg (2.8 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to count
Summary of the content on the page No. 3
still does not fit, contact a qualified elec- key that is left attached to a rotating part of trician to install a polarized outlet. Do not the tool may result in personal injury. change the plug in any way. Double insula- 13. Do not overreach. Keep proper footing tion eliminates the need for the three wire and balance at all times. Proper footing and grounded power cord and grounded power balance enables better control of the tool in supply system. unexpected situations. 5. Avoid body contact
Summary of the content on the page No. 4
22. Use only accessories that are recom- tenance performed by unqualified personnel mended by the manufacturer for your could result in a risk of injury. model. Accessories that may be suitable for 24. When servicing a tool, use only identical one tool, may become hazardous when used replacement parts. Follow instructions in on another tool. the Maintenance section of this manual. Use of unauthorized parts or failure to follow SERVICE Maintenance instructions may create a risk of 23. Tool servic
Summary of the content on the page No. 5
SPECIFIC SAFETY RULES USB057-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to impact driver safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 2. Hearing protection should be worn when when performing an operation where the operating in impact conditions. cutting tool may contact hidden wiring or 3. Hold the tool firmly. its own cord. Contact with a
Summary of the content on the page No. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002816 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. 1 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. 1. Switch trigger Release the switch trigger to stop. Electr
Summary of the content on the page No. 7
001266 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Do 12 mm 9 mm not use any other driver bit or socket bit. (15/32”) (3/8”) 001267 To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. 1 2 NOTE: • If the bit is not inserted deep e
Summary of the content on the page No. 8
The pilot holes should be slightly smaller than the wood screws in diameter. • The size of wood screw which can be fastened with this tool may differ depending upon the type of material to be fastened. Always perform a test operation to determine the size of wood screw. • When fastening bolts or nuts, always perform a test operation to verify the adequate fastening time for your bolt or nut. Excessive fastening torque may damage the bolt/nut or socket bit. MAINTENANCE CAUTION: • Always be sure t
Summary of the content on the page No. 9
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Screw bits 9
Summary of the content on the page No. 10
Memo 10
Summary of the content on the page No. 11
Memo 11
Summary of the content on the page No. 12
Memo 12
Summary of the content on the page No. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Summary of the content on the page No. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Summary of the content on the page No. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (502) 326-3740 (505) 881-4619 (787) 250-8776 ARIZONA CONNECTICUT LOUSIANA NEW YORK TENNESSEE 3707 E. Broadway Rd., Ste. 6 508 Spring St.
Summary of the content on the page No. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
