Summary of the content on the page No. 1
Bar Code Handy Terminal
BHT-400B-CE/400BW-CE
User’s Manual
Summary of the content on the page No. 2
If you leave the BHT with the battery cartridge discharged or with no battery cartridge loaded or if you replace the battery cartridge in a wrong way, the BHT may lose the data stored in it. Before cold booting (refer to Chapter 2, Section 2.3.5 "Warm and Cold Booting"), it is recommended that important data be saved into the FLASH folder or uploaded to the host computer. Cold booting will erase all data stored in the RAM. DENSO WAVE INCORPORATED does not ass
Summary of the content on the page No. 3
Copyright © DENSO WAVE INCORPORATED, 2007 All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. Microsoft, Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. Other products and company names mentioned in this manual are trademarks or registered trademar
Summary of the content on the page No. 4
US and Canada Regulations BHT-400BW-CE contains Wireless LAN module (type WM-G-MR-01) that complies with Part 15 of FCC rules and RSS-Gen of IC rules. For Wireless LAN module This device complies with Part 15 of FCC rules and RSS-Gen of IC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FC
Summary of the content on the page No. 5
BHT-400B-CE and BHT-400BW-CE comply with Part 15 of FCC rules and ICES-003 of IC rules. For Barcode Handy Terminal This device complies with Part 15 of FCC rules and ICES-003 of IC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the
Summary of the content on the page No. 6
Declaration of Conformity (For European Union) The radio frequency module that complies with the Directive 99/5/EC(R&TTE) is mounted on this device (BHT-400BW-CE). DECLARATION OF CONFORMITY Directive 99/5/EC (R&TTE) Manufacturer or Authorized representative : DENSO WAVE INCORPORATED Address : 1-1 Showa-cho, Kariya-shi, Aichi-ken, 448-8661, Japan We declare on our sole responsibility, that the following product : - Kind of equipment : Radio frequency module - Type-designation : WM-G
Summary of the content on the page No. 7
Labeling ■BHT-400B-CE ■BHT-400BW-CE For USA and Canada For European Union For USA and Canada For European Union
Summary of the content on the page No. 8
Preface Please READ through these operating instructions carefully. It will enable you to operate your BHT-400B-CE/400BW-CE correctly. The following contents are explained in this guide: • Handling and operating methods for the BHT-400B-CE/400BW-CE • Communication • Error messages • Specifications • Handling and operating methods for the optical communication unit CU-400 series The BHT-400B-CE/400BW-CE models are designed in the same way except for the interface differences shown in
Summary of the content on the page No. 9
How this book is organized This manual is made up of five chapters and appendices. Chapter 1 Quick Guide Describes the basic operating method of the BHT and the related notes. Chapter 2 Getting Started the BHT and System Menu Summarizes the BHT system configuration and describes the operation including preparation and System Mode (which is required for the efficient use of application programs). Chapter 3 Communications Operations of the BHT Describes the communications operations o
Summary of the content on the page No. 10
Related Publications BHT-400-CE API Reference Manual BHT-400-CE Class Library Reference Manual 2D Code Scanner/Barcode Scanner Keyboard Interface with BHT-CE kbifCE User’s Guide Screen Indication The lettering in the screens in this manual is a little different from that in the actual screens. File names used are only for description purpose, so they will not appear if you have not set files having those names. iii
Summary of the content on the page No. 11
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. Please READ through this manual carefully. It will enable you to use the BHT and CU correctly. Always keep this manual nearby for speedy reference. Strict observance of these warnings and cautions is a MUST for preventing accidents that could result in bodily injury and substantial property damage. Make sure you fully understand all definitions of these terms and symbols given below before you proceed to the text its
Summary of the content on the page No. 12
Handling the battery cartridge • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury. • Do not carry or store the battery cartridge together with metallic ball-point pens, necklaces, coins, hairpins, etc. Doing so could short-circuit the terminal pins, causing the batteries to rupture or the battery fluid to leak, resulting in a fire or bodily injury. • A
Summary of the content on the page No. 13
Handling the BHT • The BHT uses a laser light for indicating the scanning range. The intensity of the laser light might be too low to inflict bodily injury. However, do not look into the laser beam or view directly with optical instruments. The BHT complies with IEC 60825-1:1993+A2:2001. In accordance with Clause 8 and 9, IEC 60825-1, the following information is provided to the user: For USA and Canada LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL IN
Summary of the content on the page No. 14
Handling the CU • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If foreign material or water gets into the CU, immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If you drop the CU so as to damage its housing, immediately unplug
Summary of the content on the page No. 15
Handling the battery cartridge • Never charge a wet or damp rechargeable battery cartridge. Doing so could cause the batteries to break, generate heat, rupture or burn. Handling the BHT • If smoke, abnormal odors or noises come from the BHT, immediately turn off the power, pull out the battery cartridge, and contact your nearest dealer. Failure to do so could cause smoke or fire. • If foreign material or water gets into the BHT, immediately turn off the power, pull out the battery
Summary of the content on the page No. 16
Handling the CU • Never disassemble or modify the CU; doing so could result in an accident such as fire or malfunction. • Never put the CU in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in a fire. • Avoid using the CU in extremely humid or dusty areas, or where there are drastic temperature changes. Moisture or dust will get into the CU, res
Summary of the content on the page No. 17
Proper Care of the BHT and CU Clean the housings, BHT charge terminals, battery cartridge terminals, and CU-400 charge terminals with a dry, soft cloth. Before cleaning, be sure to turn the BHT power off and unplug the AC adapter of the CU. • Never use benzene, alcohol, or other organic solvents. The housing may be marred or the paint may come off. • Never rub or strike the liquid crystal display (LCD) with anything hard. The LCD surface will be easily scratched or broken. • When cleani
Summary of the content on the page No. 18
DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the warranty period. Intellectual Property Precaution DENSO WAVE INCORPORATED ("DENSO WAVE") takes reasonable
Summary of the content on the page No. 19
Chapter 1 Quick Guide Chapter 2 Getting Started the BHT and System Menu Chapter 3 Communications Operations of the BHT Chapter 4 Error Messages Chapter 5 Handling the CU-400 (Option) Appendices
Summary of the content on the page No. 20
