Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
MTM
MSM
FUSION MEDIUM HEIGHT ADJUST
FLAT PANEL MOUNTS
MSM/MTM Series
Summary of the content on the page No. 2
MSM/MTM Series Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and CAUTION: A CAUTION alerts you to the possibility of subsidiaries (collectively "Milestone"), intend to make this damage or destruction of equipment if you do not follow the manual accurate and complete. However, Milestone makes no corresponding instructions. claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possib
Summary of the content on the page No. 3
Installation Instructions MSM/MTM Series DIMENSIONS 25.60 MSM [650] MAX HORIZONTAL SPACING 18.79 .50 477.4 [12.7] 16.00 UP/DOWN 406.4 ADJUSTMENT EACH SIDE .35 7.63 .32 8.9 193.7 8.1 1.52 38.5 7.53 191.2 16.50 15.75 419.1 1.00 400 13.53 6.00 25.4 15.10 MAX 343.7 152.4 383.4 1.96 1.75 VERTICAL 49.8 44.5 SPACING .33 RAILS SLIDE 8.3 LEFT/RIGHT .50 FOR STUD OFFSET 12.7 1.00 25.4 25.00 635 MTM 26.25 [667] MAX HORIZONTAL SPACING 18.79 .50 477.4 [12.7] UP/DOWN 16.00 ADJUSTMENT 12° 406.4 EACH SIDE MAX TI
Summary of the content on the page No. 4
Installation Instructions MSM/MTM Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging los
Summary of the content on the page No. 5
MSM/MTM Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 7/32" (5.5mm) Wood Stud 5/16" (7.9mm) Concrete PARTS B (1) C (1) A (1) D (1) [Included with MSM6XXX/MTM6XXX E (1) Models Only] (MSM Only) Custom J (1) [Used on MSMU/MTMU Models Only] MSM6XXX/ MTM6XXX F (1) (MTM Only) Hardware (MSM Only) J1 (8) J2 (6) J3 (6) M4x16mm M4x20mm M4x25mm J4 (6) J5 (6) J6 (6) G (1) M5x16mm M5x20mm M5x25mm (MTM Only) K (1) J9 (1) H (1) J7 (6) J8 (6) M5 M6
Summary of the content on the page No. 6
MSM/MTM Series Installation Instructions 4. Measure up 7-1/2" from the center point to mark location of INSTALLATION the upper mounting slots. The MTM and MSM have been designed to be mounted directly 5. Using a level, mark the wall on each stud to attach the onto either a wood stud or concrete wall. The MTM has mount through the upper mounting slots. (See Figure 2) brackets which allow the TV to be tilted. The MSM has static NOTE: The MSM and MTM may be attached through the brackets which keep
Summary of the content on the page No. 7
Installation Instructions MSM/MTM Series 9. Drill 7/32" pilot holes at markings for lower mounting holes. (See Figure 3) WARNING: EXPLOSION AND FIRE HAZARD! CUTTING 10. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH washers (K2) [one lag bolt and washer for single stud OR SERIOUS PERSONAL INJURY! ALWAYS make certain installation] to attach the mount to the wall through the lower mounting holes. (See Figure 3) area behind mounting surface is
Summary of the content on the page No. 8
MSM/MTM Series Installation Instructions 8. Mark the attachment points for the lower mounting slots. (See Figure 4) Mounting 9. Drill one pilot hole at each marking for lower mounting Holes holes. (See Figure 4) 10. Install an anchor (K1) into each pilot hole using a hammer. 11. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat washers (K2) to attach the mount to the wall through the Mounting 1 lower mounting holes. (See Figure 4) Slot 12. Slide rails to approximate center of screen locati
Summary of the content on the page No. 9
Installation Instructions MSM/MTM Series Center Line (CL) 3d 3e Pullstraps NEVER place both interface brackets to one side of the wall mount center line (CL)! Knobs to outside of brackets Figure 7 3. If necessary, the tilt interface bracket knobs may be switched to allow the interface brackets to be reversed. (See Figure 7) a. Remove display from mount. b. Remove interface brackets from display. c. Hold the right interface bracket horizontally, tightly gripping it so that spacers do not
Summary of the content on the page No. 10
MSM/MTM Series Installation Instructions 1 Raises screen Lowers screen 2 (H) Top Hook 2 (Screen not shown for clarity) Figure 10 Locking Mount (Optional) 1. Add optional security bracket (F or G) to the mount. (See Figure 11) 2. Add padlock (not included) to complete security. Pullstraps 5 (Screen not shown for clarity) (G) 1 Figure 9 2 2. Hang top hook of interface brackets onto the top bar of the mount. (See Figure 9) NOTE: The screen initially installs into the "kickstand mode" to allow easy
Summary of the content on the page No. 11
Installation Instructions MSM/MTM Series 11
Summary of the content on the page No. 12
MSM/MTM Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a division of Asia Pacific A Room 24F, Block D, Lily YinDu International Building Milestone AV Technologies LuoGang, BuJi Town, Shenzhen, CHINA. 8831-000024 P +86-755-8996 9226 2008 Milestone AV Technologies F +86-75
